-
Demco KK260 - page 1
Page 1 OPERA T ORS MANUAL KK260 (8 WIDE ) & KK360 (8-1/2 WIDE ) KAR-KADDY DOING OUR BEST T O PROVIDE YOU THE BEST DEMCO Dethmers Mfg. Co. 4010 320th St. P .O. Box 189 Boyden, IA 51234 PH: (712) 725-2311 Toll Free: 1-800-543-3626 FAX: 1-800-845-6420 www.demco-products.com ASSEMBLY CALIBRATION OPERATION REPLACEMENT ...
-
Demco KK260 - page 2
Page 2 Thank you for purchasing a Demco Kar-Kaddy. We feel you have made a wise choice and hope you are completely satisfied with your new piece of equipment. GENERAL INFORMA TION 1. Unless otherwise specified, high-strength (grade 5) (3 radial-line head markings) hex head bolts are used throughout assembly of this piece of equip- ment. 2. Whenever ...
-
Demco KK260 - page 3
Page 3 BOL T TORQUE TORQUE DA T A FOR ST ANDARD NUTS, BOL TS, AND CAPSCREWS. T ighten all bolts to torques specified in chart unless otherwise noted. Check tightness of bolts periodically , using bolt chart as guide. Replace hardware with same grade bolt. NOTE: Unless otherwise specified, high-strength Grade 5 hex bolts are used throughout assembly ...
-
Demco KK260 - page 4
Page 4 SAFETY Safety is of utmost importance at all times. There are several items that must be checked each time before using and while using the Kar Kaddy. Make sure all bolts are properly tightened and those requiring a set torque are up to specifications: Tie Rod Castle Nut - 75 ft./lbs. Lug Nuts - 75 to 80 ft./lbs. Check Lug Nut tension after ...
-
Demco KK260 - page 5
Page 5 TESTING LIGHTS BEFORE USE 1. Check that the WHITE (ground) wire of the wiring harness is connected to the Kar Kaddy frame and the WHITE (ground) wire is connected to the frame of the towing vehicle. 2. With headlights in "ON" position, the tail lights, the light cluster bar, the license plate light, and the clearance lights should ...
-
Demco KK260 - page 6
Page 6 Step 5. Grasp bed release handle on tongue and pull toward coupler. This releases the tilt bed to permit loading. Step 7. Drive vehicle onto the platform - front forward - until tires touch the wheel stops at the front of each side of the platform and the platform tilts to a flat position. Make sure the car is centered on the platform. Towed ...
-
Demco KK260 - page 7
Page 7 Examine winches and straps to make sure they are in good condition. Check wheel nuts every trip. Tires must be inflated to recommended pressure by tire manufacturer. Be certain the safety lock pins lock the strap winches. Retighten the straps over the tires after the first 5 miles of travel. Check straps every 50 miles th ...
-
Demco KK260 - page 8
Page 8 Right Fender 1 2 45 45 34 35 43 37 38 42 48 49 49 40 41 39 44 46 47 53 86 46 47 52 52 10 100 54 54 55 55 56 56 57 58 35 58 51 42 36 66 82 2 5 81 80 78 51 89 90 90 103 104 33 109 110 111 112 113 114 108 107 106 105 100 99 98 *69 *69 *69 *69 72 75 63 62 65 75 46 88 61 60 KK260 (8'wide) and KK360 (8-1/2' wide) P ARTS BREAKDOWN 50 5217 ...
-
Demco KK260 - page 9
Page 9 KK6LBAS License Plate Mount and Light Cluster (not available) 25 25 24 26 26 27 29 30 30 31 31 32 84 27 27 78 79 77 75 76 51 74 55 42 85 73 130 *70 *70 *70 *70 104 109 115 103 64 68 67 93 94 95 102 Left Fender Left Winch Shown 15 14 13 10 9 4 12 19 20 20 22 16 18 17 23 21 7 6 12 11 8 3 5 1. 5432 1 Left Ratchet Winch Assembly (Plated) 2. 5433 ...
-
Demco KK260 - page 10
Page 10 REF. PART NO. NO. QTY. DESCRIPTION 29. 02580-95 1 License Plate Clip 30. 02770 2 1/4-20UNC Nylon Insert Wing Nut 31. 01077 2 1/4"-20UNC Serrated Locknut 32. 04513 1 Light Cluster 10. 02243 2 Black Vinyl Hand Grip 33. 01883 11 Electrical Wire Splicer 34. 01881 1 Trunk Connector 35. 04785 1 Front Half Trailer Wiring Harness 36. 04786 1 R ...
-
Demco KK260 - page 11
Page 11 1. Extent and Duration of this Warranty: Your Demco Kar Kaddy is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year after date of purchase by the original (first) retail owner, or until it is resold or transferred by the original owner. New Departure Hyatt Hubs used on the KK ...
-
Demco KK260 - page 12
Page 12 Model DA66 ACTUA TOR P ARTS BREAKDOWN - 8606701 1 DA66 Brake Actuator complete (incl. ref. 1-25) - 5400 - Lever Replacement Kit (incl. items w/*) - 5398 - Master Cylinder Repair Kit w/ gasket - 5495 - Coupler Repair Kit ACTUATOR PARTS LIST Please order replacement parts by PART NO. and DESCRIPTION. REF. PART N O . N O . QTY. DE SCRIPTION 2 ...
-
Demco KK260 - page 13
Page 13 5695 - Emergency Lock Cam Replacement Kit 20. ----- 1 7/16î-14UNC x 1 1/4î Hex Head Bolt (Gr. 5) 21 . ----- 1 7/16î-14UNC Lock Nut (Center Punch) 22. ----- 1 Emergency Catch Cam (black oxide finish) 23 . ----- 1 Pushrod Assembly (includes cable) 5696 - Coupler Repair Kit (2î lever lock) 5398 - Master Cylinder Repair Kit w/ gasket DA603 ...
-
Demco KK260 - page 14
Page 14 MODEL DA91 ACTUA TOR P ARTS BREAKDOWN 5398 Master Cylinder Repair Kit (gasket included) 2î Lever Lock Coupler RATED AT 6000# not included REF. N O . PART NO. QTY. DE SCR IPTION Model 91 ACTUATOR PARTS LIST 1. 09417 1 6000# 2" Lever Lock Coupler (zinc plated) 2. 01896 3 1/2"-13UNC x 4" Hex Head Bolt (gr.5) 3. 02178 3 1/2" ...
-
Demco KK260 - page 15
Page 15 4 4 5 5 7 16 2 2 1 16 3 8 6 10 10 18 17 13 REF. PART N O . N O. QTY. DESCRIPTION BRAKE CLUSTER PARTS LIST 11 12 9 15 17 14 17 18 17 - SB24429 - Left Hand Cluster (shown above) - SB24428 - Right Hand Cluster 1. SB23871 1 Back Plate Assembly - (NDH Hub Mounting) 2. SB9254 2 Cover Plate - Adjusting Hole 3. SB10954 1 Brake Shoe Kit (includes 2 ...
-
Demco KK260 - page 16
Page 16 OPTIONAL SURGE BRAKES (KK260SB and KK360SB) P ARTS BREAKDOWN Model DA603 Brake Actuator 1 2 3 4 5 5 6 7 8 2 9 Please order replacement parts by PART NO. and DESCRIPTION. SURGE BRAKES PARTS LIST 1. SB587 1 87" Brake Line 2. 01863 2 Rubber Gommet 3. 02746 1 54" Protective Hose 4. SB7H67 1 7" Brake Hose (rubber) 5. SB536 2 36&qu ...
-
Demco KK260 - page 17
Page 17 KK260 AND KK360 ASSEMBLY INSTRUCTIONS 1. Place the main frame on blocks or some other sturdy support so that the frame rests approximately 8" - 10" off the ground. Attach the tilt bed ramps (#1) as shown using four 1/2" x 1-1/4" grade 5 bolts (#4), flat washer (#5) and lock nuts (#6), two on each side of each ramp, and t ...
-
Demco KK260 - page 18
Page 18 11. DO NOT MOVE THE TIE ROD LOCKING CLAMP FROM ITS FACTORY PRESET POSITION. GREASE TIE ROD ENDS BEFORE USING. NOTE: Tie rods are factory set and should not be readjusted. 12. Bolt on the steering stabilizer cylinder (#1) as shown using a 5/8" x 2-3/4" bolt (#2) coming up from the bottom, through a 5/8" flat washer (#3), throu ...
-
Demco KK260 - page 19
Page 19 WIRING & FENDER ASSEMBLY INSTRUCTIONS NOTE: It is advantageous to wire the fender lights prior to attaching the wheels. 1. Cut off stripped ends of the wiring harness, cut off stripped ends of the front clearance light, and cut off the stripped end of the white ground wire. The yellow/brown wires must be run to the left tail light pocke ...
-
Demco KK260 - page 20
Page 20 12" 12" C L BACK MEASUREMENT FRONT MEASUREMENT (1/32" to 1/16" less than back measurement) 18" Ground 1. Put a mark on each side of the locking clamp on the tie rod. 2. Loosen the locking nuts on each end of the tie rod and then the six bolts on the tie rod locking clamp. 3. Turn the tie rod whichever direction is n ...
-
Demco KK260 - page 21
Page 21 - KK2WJ 1 Optional Wheel Jack w/ hardware Please order replacement parts by PART NO. and DESCRIPTION. OPTIONAL WHEEL JACK WHEEL JACK PARTS LIST * All options may not mount on tow dolly simultaneously.* REF. PART NO. NO. QTY. DES CRIPTION KK2DF Optional Deflector 1. 02055-25 2 Deflector Framework 2. 02592 4 3/8"-16UNC Nylon Insert Lock ...
-
Demco KK260 - page 22
Page 22 1. 00059 4 3/8" Flatwasher 2. 02592 8 3/8"-16UNC Nylon Insert Locknut 3. 01888-25 1 Tool Box 4. 00182 1 Small Hair Pin 5. 02742-25 2 Mounting "Z" Bracket 6. 00907 4 3/8"-16UNC x 1" Hex Head Bolt (gr.5) 7. 02759 2 3/8"-16UNC x 3" Square U-Bolt OPTIONAL WINCH KK2TB 1 Optional Tool Box OPTIONAL T OOL BOX ...
-
Demco KK260 - page 23
Page 23 NOTES ...
-
Demco KK260 - page 24
Page 24 DETHMERS MFG. COMPANY P.O. BOX 189 4010 320th St., BOYDEN, IA. 51234 PH: (712) 725-2311 FAX: (712) 725-2380 TOLL FREE: 1-800-54DEMCO (1-800-543-3626) www.demco-products.com ...
Do you have a question concerning Demco KK260?
Use the form below
If you did not solve your problem by using a manual Demco KK260, ask a question using the form below. If a user had a similar problem with Demco KK260 it is likely that he will want to share the way to solve it.