English dropdown-ico

Manual Studer XPC 1400-12

23 pages 0.51 mb
Download

Go to site of 23

Summary
  • Studer XPC 1400-12 - page 1

    STUDER INNOTEC XP- COMPACT User manual XP-COMPACT V5.1 E User and installer Manual Combi Inverter, Battery charger and Transfersystem XP-COMPACT XPC 1400-12 XP-COMPACT XPC 2200-24 XP-COMPACT XPC 2200-48 Remote control RCC-01 Temperature sensor CT-35 Solar charge controller XPCxxxx-S AC cable cover CFC-01 IP-23 top cover C-IP23 STUDER INNOTEC TEL: + ...

  • Studer XPC 1400-12 - page 2

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 1 Summary 1 General Info rmation ............................................................................................................ ..... 3 1.1 O PERATING INSTRUCTIONS ................................................................................................................... ...

  • Studer XPC 1400-12 - page 3

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 2 4.8.3 De layed mode of the Trans fer System ............................................................................................ ............. 15 4.9 T HE S OLAR CHARGE CONTROLLER ( OPTION ) ............................................................................................ ...

  • Studer XPC 1400-12 - page 4

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 3 1 General Information 1.1 Operating instructions This manual is a part of the delivery package of every XP-COMPACT inverte r-charger. It serves as guidelines for safe and efficient operation of XP -COMPACT. The instructions are only valid for use with the following appliances and options: - ...

  • Studer XPC 1400-12 - page 5

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 4 1.5 Precautions This manual must be readily available for the user at all times. The use r must be familiar with the precautions and safety aspects. During operation of XP-COMPACT, high voltages are generated at the connection s and inside of the appliance which could be deadly fatal. Work ...

  • Studer XPC 1400-12 - page 6

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 5 2 Introduction The XP-COMPACT is a sine wave inverter with integrated battery char ger and solar charge con- troller with many additional functions, it has been developed to be used as stand -alone (no grid feeding) AC provider, or as continuous / b reak-free current supply provider (UPS). ...

  • Studer XPC 1400-12 - page 7

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 6 2.2.3 The battery charger The built-in battery charger is so designed that it can charge the battery quickly and fully. A micro- processor controlled, 3 to 4 Step charging proc ess ensures the optimum charging of the batteries. The desired charging current can be set continuously from 0 to ...

  • Studer XPC 1400-12 - page 8

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 7 2.3.3 Connection in parallel and in serie 3 Mounting and installing 3.1 Installation place The location of the XP-COMPACT must be chosen by the following criteria: - Protection against unauthorized ha ndling - Dry dust free room, no condensation - Never install direct ly over the battery an ...

  • Studer XPC 1400-12 - page 9

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 8 Connecting must be done by qualif ied staff. Material such as cable, connecto rs and distribution boxes, fuses etc. used in the installation must comply w ith the respective valid low-voltage installa- tion rules and regulations. 3.4.2 Protection cover fo r the terminals con- nections The p ...

  • Studer XPC 1400-12 - page 10

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 9 3.6 Cabling/wiring Connecting of the XP-COMPACT is a very important step in the installation. You must take care that all connecting work is carried out in a clean and correct manner and that under no circum- stance a cable is connected to a w rong terminal. Connecting of the XP-COMPACT mus ...

  • Studer XPC 1400-12 - page 11

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 10 XPC 1400-12 17-25V/30A, XPC 2200-24 34 – 45V/30A, XPC 2200-48 68 – 90V/20A. 3.6.6 Connection to Auxiliary Cont act On these three terminals is a potential fre e ch ange-over contact. The maximal permitted current and voltage for this is 16A/250Vac. The LED 5 “Contact active” shows ...

  • Studer XPC 1400-12 - page 12

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 11 4.2 Display and control parameters on remote control panel (optional) 16 0 OFF AC OUT Over Temp. Over load AC IN SOLAR CHARGE Contact manual Contact acti ve Pr ogra m COM PAC T AUXILIARY CONTACT ON/OFF INVERTER - CHARGER (Select) RCC-01 INV ERTER CHARGER (Program) (Change s tatus) Ba ttery ...

  • Studer XPC 1400-12 - page 13

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 12 wiring of the installation 12 Batt. Low/High Battery voltage is too low Battery voltage is too high 13 OFF XP-COMPACT is turned off. Turn- ing it back on is only possible manually. XP-COMPACT is for the time be- ing turned off. Turning it back on will follow automatically! 14 Battery Charg ...

  • Studer XPC 1400-12 - page 14

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 13 1.9 2.3 2.50 [V/cell] 2.1 A B C D 20 60 40 70 [A] A B C D t Equalizat ion Absorption Floati ng Charging c urrent (adjusted) Charging ti me Egalization t ime Absorption ti me Floatin g 4.6.3 Overheating (O ver Temp) If the Inverter has been overloaded for a long time or it ha s been working ...

  • Studer XPC 1400-12 - page 15

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 14 4.7.2 Equalization c harging Before you program the XP-COMP ACT for Equalizat ion-charge you must check with your supplier that the batteries are suitable for this process. Equalization is recommended for the lead -acid batteries in order to mix well the electrolyte fluid and to clean the ...

  • Studer XPC 1400-12 - page 16

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 15 the transfer contact is active, then you have at the output AC OUT the same voltage as that at the input. This voltage can not be modified by the XP-COMPACT! 4.8.1 Set the transfer voltage threshold The voltage threshold of the transfer is factory settled at 200Vac. This value is acceptabl ...

  • Studer XPC 1400-12 - page 17

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 16 4.10 The Multifunctional Contact In the XP-COMPACT there is a built-in power re lay. The potential-free change-over contact (NO – NC) of this power relay is connected to the screw terminal AUX CONTACT. Maximum Contact load: 230Vac /12Vdc/24Vdc/16Amp 60Vdc/3 Amp. ! The contact is activate ...

  • Studer XPC 1400-12 - page 18

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 17 5.3 Battery Condition Built-in microprocessor calculates t he actual state of charge of the battery and displays it on LED 15 – 18. The LED 14 is lit when the system is carrying out a charge cycle with equalization. The voltage levels and charge characteristics can be changed through Pro ...

  • Studer XPC 1400-12 - page 19

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 18 6.1 Standard setting The XP-COMPACT (except for 60Hz version s) is equipped with a Flash processor fi tted out with EEPROM Memory, which means that even when it is disconnected from the battery, the parame- ters that were programmed for the application remain after a new connection to the ...

  • Studer XPC 1400-12 - page 20

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 19 OFF Over Temp. Overlo ad ON/OFF (Sel ect) (Chan ge s tatus) Ba ttery Low/High RE SET ALARM 15 16 17 18 19 21 13 12 11 10 20 14 These four red LED show the function set: Low voltage LED 13 Float charge LED 12 Absorption (End of charge) LED11 Equalization LED 10 Absorptions Time LED 10/11/12 ...

  • Studer XPC 1400-12 - page 21

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 20 6.4.3 Example 6.4.3.1 Auxiliary Contact as generator starter When in the programming of the Auxiliary Contact, the Battery Capacity (LED 15-18) is used as a condition, then you must take note of the follow ing requirements. If you have to start an emergency back-up supply w i th a battery ...

  • Studer XPC 1400-12 - page 22

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 21 7 Maintenance Apart from the periodic contro ls mentioned fo r the connections, the XP-COMPACT does not need any maintenance. Keep the appliance clean and from time to time wipe it clean with a damp cloth. 8 CE Compliance Hereby we state that the products described in th is user manual mee ...

  • Studer XPC 1400-12 - page 23

    STUDER Innotec XP- COMPACT User manual XP-COMPACT V5.1 E 22 9 Technical Data Model XPC 1400-12 XPC 2200-24 XPC 2200-48 Inverter Nominal battery voltag e 12V 24V 48V Input voltage range 9.5 – 16V 19 - 32V 38 - 64V Continuous power @ 2 5°C 1100VA 1600VA 1600VA Power 30 min. @ 25°C 1400VA 2200VA 2200VA Maximum power load 5 sec. 3 x Pnom Maximum lo ...

Manufacturer Studer Category Battery Charger

Documents that we receive from a manufacturer of a Studer XPC 1400-12 can be divided into several groups. They are, among others:
- Studer technical drawings
- XPC 1400-12 manuals
- Studer product data sheets
- information booklets
- or energy labels Studer XPC 1400-12
All of them are important, but the most important information from the point of view of use of the device are in the user manual Studer XPC 1400-12.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Studer XPC 1400-12, service manual, brief instructions and user manuals Studer XPC 1400-12. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Studer XPC 1400-12.

Similar manuals

A complete manual for the device Studer XPC 1400-12, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Studer XPC 1400-12 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Studer XPC 1400-12.

A complete Studer manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Studer XPC 1400-12 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Studer XPC 1400-12, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Studer XPC 1400-12, that we can find in the current document
3. Tips how to use the basic functions of the device Studer XPC 1400-12 - which should help us in our first steps of using Studer XPC 1400-12
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Studer XPC 1400-12
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Studer XPC 1400-12 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Studer XPC 1400-12?

Use the form below

If you did not solve your problem by using a manual Studer XPC 1400-12, ask a question using the form below. If a user had a similar problem with Studer XPC 1400-12 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)