English dropdown-ico

Manual Shindaiwa 63888-94010

18 pages 0.53 mb
Download

Go to site of 18

Summary
  • Shindaiwa 63888-94010 - page 1

    SHINDAIW A OWNER’S/ OPERA TOR'S MANUAL P231 POLE PRUNER WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit. Part Number 63888-94010 Rev. 2/02 Shindaiwa Inc. P.O. Box 2810 Tualatin, Oregon 97062 Telephone: 503 ...

  • Shindaiwa 63888-94010 - page 2

    Introduction The Shindaiwa P231 Pole Pruner is designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa’s high-performance engines represent the leading edge of 2-cycle engine technology, delivering exceptionally high power with remark- ably low displacement and wei ...

  • Shindaiwa 63888-94010 - page 3

    Safety Pr ecautions A pole pruner operates at very high speeds and has the potential to do serious damage if misused, abused or mishandled. To reduce the risk of injury, you must maintain control at all times, and observe all safety precau- tions during operation. Never permit a person without training or instruction to operate this pruner! WARNING ...

  • Shindaiwa 63888-94010 - page 4

    Both kickback and pinching may cause you to lose control of the pole pruner which could result in serious personal injury. Do not rely exclu- sively on the safety device built into the pruner! You must take several steps to keep your jobs free from accident or injury: 1. Understand kickback and pinching! You can reduce or eliminate the element of s ...

  • Shindaiwa 63888-94010 - page 5

    5 P231_2 Always operate with both hands firmly gripping the unit. Wear nonslip heavy- duty work gloves to improve your grip on the pole pruner handle. Wear snug-fitting clothes that also permit freedom of movement. NEVER wear shorts! Always wear a hard hat to reduce the risk of head injuries during operation of this unit. Always wear eye and hearin ...

  • Shindaiwa 63888-94010 - page 6

    6 IMPORTANT! Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged or missing information labels. New labels are available from your local autho- rized Shindaiwa dealer. Safety Equipment and Labels Shaft Safety Label Figure 2 Throttle Interlock Ignition Switch High Voltage ...

  • Shindaiwa 63888-94010 - page 7

    Operating Precautions ■ Make sure the chain and sprocket are correctly adjusted before operating the pruner (see page 15 for adjustment procedures). Never attempt chain adjustment with the engine running! ■ Always make sure the cutting attachment is properly installed and firmly tightened before operation. ■ Never use a cracked or warped guid ...

  • Shindaiwa 63888-94010 - page 8

    8 Figure 3 CAUTION! ■ Always maintain the P231 pole pruner according to the this owner’s manual and follow the recommended scheduled maintenance. ■ Never modify or disable any of the pole pruner’s safety devices. ■ Always use genuine Shindaiwa parts and accesso- ries when repairing or main- taining this unit. ■ Do not make unauthorized ...

  • Shindaiwa 63888-94010 - page 9

    P231 Specifications Dry Weight ................... 6.1 kg/ 13.4 lb. Length w/10" bar assembly .......... 2804 mm/ 110.4 in. Engine Type ............ 2-cycle, air-cooled, vertical-cylinder Bore x Stroke ... 3 2 x 2 8 m m / 1.3 x 1.1 in. Displacement ......... 22.5 cc/ 1.4 cu. in. Maximum Output .......... 0.8kW/ 1.1 hp @ 7500 rpm (min -1 ) Fuel ...

  • Shindaiwa 63888-94010 - page 10

    Lower Tube Handle Grip Ignition Switch Coupler Bar and Chain Upper Tube Throttle Trigger Product Description IMPORTANT! The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation. Prior To Assembly Using Figure 4 a ...

  • Shindaiwa 63888-94010 - page 11

    11 Grip Spark Plug Ignition Switch Main Shaft Tube Clamp Outer Tube 1. Place the powerhead on a clean, flat surface, spark plug facing up. See Figure 5. Tube Clamp Hex Wrench Shim Washer Connect the Outer Tube to the Powerhead. Clamp Screw Figure 5 Figure 6 Throttle Lever Driveshaft/Powerhead Assembly CAUTION! Do not force the shaft tube into the p ...

  • Shindaiwa 63888-94010 - page 12

    12 23145 23106 Remove the Cylinder Cover. 1. Remove the spark plug boot. 2. Remove the two lower cylinder cover screws. 3. Loosen the top cylinder cover screw until the cover is free of the engine. (The top cylinder cover screw is captive). Lift the cylinder cover off of the engine. See Figure 7. Connect the Throttle Cable. Cable Adjuster Ignition ...

  • Shindaiwa 63888-94010 - page 13

    13 Assemble and Adjust the Throttle Cable. 1. Insert the throttle cable housing into the notch on the fan cover, and clamp the black wire’s connector between the fan cover and the cable outer adjuster nut. See Figure 10. 2. Tighten the two throttle cable adjuster nuts. Spark Plug Boot Black Wire Ignition Ground Lead Black Wire 3. Using finger pre ...

  • Shindaiwa 63888-94010 - page 14

    P231_13 P231_12 Assembling the T ube Sections Figure 11 Tube Assembly Disassembling The Pole Sections 1. With the pole pruner on a clean, flat surface, loosen the coupler screw. The spring-loaded coupler protec- tor should pop up. 2. Press down on the latch with your finger or thumb. See Figure 13. This releases the coupler lock. Tube Assembly Coup ...

  • Shindaiwa 63888-94010 - page 15

    P231_15 Sprocket Cover Nut Sprocket Cover P231_17 P231_16 Installing and Adjusting the Bar and Chain BAR TIP Top of Bar Bottom of Bar P231_18 Figure 14 Figure 15 Guide Bar Adjustment Stud Guide Bar Chain Tensioning Screw Chain Tensioning Pin Guide Bar Adjustment Stud Chain Tensioner Hole 15 Installing The Chain 1. Using the small end of the plug wr ...

  • Shindaiwa 63888-94010 - page 16

    P231_19 Sprocket Cover Nut P231_20 Adjusting the Chain 1. Place the pole pruner on a clean, flat surface. (For readjustment during operation, shut down the engine, then allow the guide bar and chain to cool before proceeding with the adjustment procedure). 2. Loosen the sprocket cover nut with a plug wrench (Figure 17). Figure 17 Figure 18 Chain Te ...

  • Shindaiwa 63888-94010 - page 17

    P231_23 P231_22 Chain Oiler Figure 20 Oil Filler Cap Figure 21 Oil Reservoir Oil Flow Adjusting Screw 17 Filling The Oil Reservoir Adjusting Oil Flow Rate CAUTION! The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw. CAUTION! An increase in bar oil flow rate will speed oil cons ...

  • Shindaiwa 63888-94010 - page 18

    18 Filling the Fuel T ank 1. Place the pole pruner on a flat, level surface. 2. Clear any dirt or other debris from around the fuel filler cap. 3. Remove the fuel cap, and fill the fuel tank with clean, fresh fuel mixture. 4. Install and firmly tighten the fuel cap. WARNING! Minimize the risk of fire! ■ Stop engine before refueling. ■ Always al ...

Manufacturer Shindaiwa Category Pole Saw

Documents that we receive from a manufacturer of a Shindaiwa 63888-94010 can be divided into several groups. They are, among others:
- Shindaiwa technical drawings
- 63888-94010 manuals
- Shindaiwa product data sheets
- information booklets
- or energy labels Shindaiwa 63888-94010
All of them are important, but the most important information from the point of view of use of the device are in the user manual Shindaiwa 63888-94010.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Shindaiwa 63888-94010, service manual, brief instructions and user manuals Shindaiwa 63888-94010. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Shindaiwa 63888-94010.

Similar manuals

A complete manual for the device Shindaiwa 63888-94010, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Shindaiwa 63888-94010 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Shindaiwa 63888-94010.

A complete Shindaiwa manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Shindaiwa 63888-94010 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Shindaiwa 63888-94010, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Shindaiwa 63888-94010, that we can find in the current document
3. Tips how to use the basic functions of the device Shindaiwa 63888-94010 - which should help us in our first steps of using Shindaiwa 63888-94010
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Shindaiwa 63888-94010
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Shindaiwa 63888-94010 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Shindaiwa 63888-94010?

Use the form below

If you did not solve your problem by using a manual Shindaiwa 63888-94010, ask a question using the form below. If a user had a similar problem with Shindaiwa 63888-94010 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)