English dropdown-ico

Manual Cabletron Systems 9F310-02

30 pages 0.4 mb
Download

Go to site of 30

Summary
  • Cabletron Systems 9F310-02 - page 1

    MMAC-Plus ™ 9F310-02 & 9F315-02 FDDI Switch Module User’s Guide ...

  • Cabletron Systems 9F310-02 - page 2

    ...

  • Cabletron Systems 9F310-02 - page 3

    i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made. The hardwar e, firmware, or softwar e described in this manual is subject to ...

  • Cabletron Systems 9F310-02 - page 4

    ii Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation. NOTE: This equipment has been tested and found to c ...

  • Cabletron Systems 9F310-02 - page 5

    v Notice Safety Inf ormation CLASS 1 LASER TRANSCEIVERS The 9F315-02 is a Class 1 Laser Pr oduct The 9F315-02 uses Class 1 Laser transceivers. Read the following saf ety inf ormation before installing or operating these adapter s. The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eli ...

  • Cabletron Systems 9F310-02 - page 6

    Notice vi Safety Inf ormation CLASS 1 LASER TRANSCEIVERS Laser Radiation and Connectors When the connector is in place, all laser radiation remains within the fiber . The maximum amount of radiant power exiting the fiber (under normal conditions) is -12.6 dBm or 55 x 10 -6 watts. Removing the optical connector from the transceiver allows laser ra ...

  • Cabletron Systems 9F310-02 - page 7

    vii Contents Chapter 1 Intr oduction Features........................................................................................................................... 1-1 Related Manuals ............................................................................................................ 1-4 Getting Help ................................... ...

  • Cabletron Systems 9F310-02 - page 8

    Contents viii ...

  • Cabletron Systems 9F310-02 - page 9

    1-1 Chapter 1 Intr oduction The 9F310-02 and 9F315-02 are thr ee port switch modules with two front panel FDDI interfaces and one INB-1 backplane interface. The external FDDI networks are connected to the modules using standar d FDDI A/B ports on the front panel. The 9F310-02 uses multi mode fiber , and the 9F315-02 uses single mode fiber optic c ...

  • Cabletron Systems 9F310-02 - page 10

    Introduction 1-2 interfaces provide frames filter ed, frames forwarded, and all Spanning T ree Protocol parameters. The 9F310-02 and 9F315-02 modules support the IETF FDDI MIB (RFC-1512), IETF MIB ll (RFC-1213), IETF BRIDGE MIB (RFC-1493), and a host of Cabletron enterprise MIBs. In addition, the fr ont panel provides LEDs for FDDI link status per ...

  • Cabletron Systems 9F310-02 - page 11

    1-3 F eatures Figure 1-1. The 9F310-02 and 9F315-02 Modules MMAC PLUS MMAC PLUS MMAC PLUS MMAC PLUS ...

  • Cabletron Systems 9F310-02 - page 12

    Introduction 1-4 Related Manuals The manuals listed below should be used to supplement the procedur es and technical data contained in this manual. MMAC-Plus Installation Guide MMAC-Plus Operations Guide MMAC-Plus 9C300-1 Environmental Module User ’ s Guide MMAC-Plus 9C214-1 AC Power Supply User ’ s Guide INB T erminator Modules Installation Gu ...

  • Cabletron Systems 9F310-02 - page 13

    2-1 Chapter 2 Installing the MMA C-Plus modules The 9F310-02 and 9F315-02 modules occupy two slots in the MMAC-Plus chassis. The modules must be installed with the left side (as viewed from the fr ont) in an odd numbered slot, and the right side in an even number ed slot. T o install the 9F310-02 and 9F315-02, follow the steps below: 1. Switch off ...

  • Cabletron Systems 9F310-02 - page 14

    Installing the MMA C-Plus modules 2-2 Figure 2-1. Installing the 9F310-02 and 9F315-02 Modules 7 F LN K 8 F LN K F LN K 10 F LN K I NS 11 F LN K I NS 12 RX TX RX TX RX Circuit Card Card Guides Metal Back-Panel Jack for ESD wrist strap W arning: Ensure that the circuit card is between the card guides . Lock do wn the top and bottom plastic tabs at t ...

  • Cabletron Systems 9F310-02 - page 15

    2-3 The Reset Switch The Reset Switch The Reset switch is located on the rightmost front panel, under the top plastic tab as shown in Figure 2-2. It serves two functions: • Pressing the r eset switch twice within three seconds causes the pr ocessor (i960) to reset. • Pressing and holding the switch on for thr ee or more seconds causes the modul ...

  • Cabletron Systems 9F310-02 - page 16

    Installing the MMA C-Plus modules 2-4 User Accessible Components Figure 2-3 shows the various components that ar e accessible to the user . These consist of an eight position dip switch (explained below), replaceable PROMs and sockets for RAM. These will be used for future upgrades. Instr uctions for installing the components will be supplied with ...

  • Cabletron Systems 9F310-02 - page 17

    2-5 User Accessible Components See the Cautions at the end of this table. T able 2-1. Function of DIP Switch Switch Function Description 8 Clear Password 1 When toggled, this switch clears user-enter ed passwords stor ed in NVRAM, and restor es the default passwords. Once r eset you can use the defaults or enter new passwords. 7 Clear NVRAM 2 The m ...

  • Cabletron Systems 9F310-02 - page 18

    Installing the MMA C-Plus modules 2-6 ...

  • Cabletron Systems 9F310-02 - page 19

    3-1 Chapter 3 Operation The 9F310-02 and 9F315-02 modules are capable of bridging/switching any thr ee, of five possible interfaces, depending on how it is configured. The INB-1 connection is always fixed. When configuring the module, the decision is made to connect both front panel ports, both FNB ports, or one fr ont panel and one FNB port to ...

  • Cabletron Systems 9F310-02 - page 20

    Operation 3-2 System Management Buses There ar e two management channels within the MMAC-Plus system: the SMB-1 and the SMB-10. These buses provide out-of-band management and inter -module management communication. SMB-1 Bus The SMB-1 is a 1Mbs management bus located within the MMAC-Plus. This bus is utilized by all diagnostic controllers in the sy ...

  • Cabletron Systems 9F310-02 - page 21

    3-3 DC/DC Conv er ter DC/DC Con verter The DC/DC converter converts the 48 VDC on the system power bus to the necessary operating voltages for its host network services module. The diagnostic controller monitors and contr ols the operation of the DC/DC converter . INB Interface Each module that attaches to the INB has an INB Network Interface Block ...

  • Cabletron Systems 9F310-02 - page 22

    Operation 3-4 The Host engine sends and receives packets via the CPU FPS Interface. This allows the bridge to perform spanning tree pr otocol and other bridging functions. The SMB Interfaces provide communication to the Host Engine for management functions and communication with other modules in the chassis. ...

  • Cabletron Systems 9F310-02 - page 23

    4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in trouble shooting. Shown in Figur e 4-1 is the LANVIEW LEDs of the 9F310-02 and 9F315-02 module. Figure 4-1. The LANVIEW LEDs INB T ransmit FDDI Status INB Receiv e FDDI Receiv e FDDI T ransmit System Status ...

  • Cabletron Systems 9F310-02 - page 24

    LANVIEW LEDs 4-2 The function of the two System Status LEDs, System Management Bus (SMB) and the CPU, are listed in T able 4-1. The function of the INB receive LEDs ar e listed in T able 4-2. The function of the INB transmit LEDs are listed in T able 4-2. T able 4-1. System Status (SMB and CPU) LEDs LED Color State Description Green Functional Full ...

  • Cabletron Systems 9F310-02 - page 25

    4-3 The function of the FDDI receive LEDs ar e listed in T able 4-4. The function of the FDDI transmit LEDs are listed in T able 4-2. The FDDI status LEDs display the status when bridging to the front panel port from either FNB ring. The “A” and “B” LEDs indicate the status of the A and B ports. The “P” and “S” LEDs indicate the sta ...

  • Cabletron Systems 9F310-02 - page 26

    LANVIEW LEDs 4-4 The functions of the FDDI Status LEDs are listed in T able 4-6. T able 4-6. FDDI Status LEDs A P S B ST A TE Green N/A N/A Gr een Ports Enabled & Active Green Gr een Off Green THRU A, MAC on Primary , Secondary Bypasses Board Green Gr een Y ellow Green THRU A, MAC on Primary , No MAC on Secondary Green Of f Green Gr een THRU B, ...

  • Cabletron Systems 9F310-02 - page 27

    5-1 Chapter 5 Specifications T echnical Specifications CPU: Intel i960 RISC based micropr ocessor Memory: 4 Meg. Local RAM (expandable to 12 Meg.) 2 Meg. Flash Memory (expandable to 16 Meg.) 2 Meg. Packet RAM Standards: ANSI FDDI X3T9.5 SMT MAC PHY MMF-PMD SMF-PMD Network Interfaces: A/B ports MMF Connectors ...

  • Cabletron Systems 9F310-02 - page 28

    Specifications 5-2 Safety This equipment meets the safety requir ements of: • UL 1950 • CSA C22.2 No. 950 • EN 60950 • IEC 950 • EMI Requirements of FCC Part 15 Class A • EN 55022 Class A • VCCI Class I • EMC requir ements of: EN 50082-1 IEC 801-2 ESD IEC 801-3 Radiated susceptibility IEC 801-4 EFT Service MTBF (MHBK-217E) >200, ...

  • Cabletron Systems 9F310-02 - page 29

    5-3 Link Distance 9F310-02 Up to 2 kilometers on multimode fiber-optic cable as specified by ANSI MMF-PMD. 9F315-02 40 kilometers (max), 25 kilometer (typical) on single-mode fiber-optic cable as specified by ANSI SMF-PMD. ...

  • Cabletron Systems 9F310-02 - page 30

    Specifications 5-4 ...

Manufacturer Cabletron Systems Category Switch

Documents that we receive from a manufacturer of a Cabletron Systems 9F310-02 can be divided into several groups. They are, among others:
- Cabletron Systems technical drawings
- 9F310-02 manuals
- Cabletron Systems product data sheets
- information booklets
- or energy labels Cabletron Systems 9F310-02
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cabletron Systems 9F310-02.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cabletron Systems 9F310-02, service manual, brief instructions and user manuals Cabletron Systems 9F310-02. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cabletron Systems 9F310-02.

Similar manuals

A complete manual for the device Cabletron Systems 9F310-02, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cabletron Systems 9F310-02 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cabletron Systems 9F310-02.

A complete Cabletron Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cabletron Systems 9F310-02 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cabletron Systems 9F310-02, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cabletron Systems 9F310-02, that we can find in the current document
3. Tips how to use the basic functions of the device Cabletron Systems 9F310-02 - which should help us in our first steps of using Cabletron Systems 9F310-02
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cabletron Systems 9F310-02
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cabletron Systems 9F310-02 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cabletron Systems 9F310-02?

Use the form below

If you did not solve your problem by using a manual Cabletron Systems 9F310-02, ask a question using the form below. If a user had a similar problem with Cabletron Systems 9F310-02 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)