English dropdown-ico

Manual Wegener Communications Unity RF Switch

6 pages 0.05 mb
Download

Go to site of 6

Summary
  • Wegener Communications Unity RF Switch - page 1

    Installation/ Operation Guide UNITY RF Sw itch Opti on Data, draw ings, an d other mate rial contained her ein are pr oprietar y to Wegener Communications , Inc., an d may not be repr oduced or duplic ated in any form wi thout the pr ior permi ssion of We gener Communi cations, Inc. When or dering part s from Wegener Communicati ons, Inc., be s ure ...

  • Wegener Communications Unity RF Switch - page 2

    Page 2 800016-13 Page 2 of 6 1. INTRODUCTI ON The UNITY RF Switch is a software-controlled, four-input, single-output, L -band switch. It allows network and local control of antenna f eed selection as well as other signal paramete rs. Please read the entire set of instr uctions before beg inning the installa tion. 2. RF SWITCH KIT INVENTOR Y In add ...

  • Wegener Communications Unity RF Switch - page 3

    Page 3 Page 3 of 6 800016-13 B. INSTALL TH E RF SWITC H See Fi gur e 1 (Pa ge 5) and Figu re 2 (Page 5) of this guide for views of the module and its installation. 1. Remove the block-out plate from the Module where the switch is to be installed. These screws and holes will be used to mount the RF Switch in a later step. Us e the #1 Philips Screwdr ...

  • Wegener Communications Unity RF Switch - page 4

    Page 4 800016-13 Page 4 of 6 C. SET RF SWITCH OP TIONS 1. Set Jumpers on the option card to the dotted position. When setting the jumpers, observe that the re are three pins on each header. The jumper covers two of these pins and connects them to gether electrically. In one position Pin 2 (center pin) is connected to Pin 1, while in the other posit ...

  • Wegener Communications Unity RF Switch - page 5

    Page 5 Page 5 of 6 800016-13 Figure 1. Typical Two-Connector-Cable Installation Figure 2. Typical T hree-Conn ector-Cable Install ation UNITY4000 MOTHER BOARD P/S Front Rear Module 1 RF Switch Expansion 1 Mounting Bracket J1 screws from blockout plate Hole used if Mounted in Module 2 STANDOFFS 3 in each Module area Hole Used If Mounted In Module 1 ...

  • Wegener Communications Unity RF Switch - page 6

    Page 6 800016-13 Page 6 of 6 SERVICE RETURN ADDRESS Service Department RMA# ________ Wegener Communications, Inc. 359 Curie Drive Alpharetta, GA 30005 SERVICE CONTACT NUMBERS AND ADDRES SES Voice: (770) 814-4057 FAX: (678) 624-0294 email: service@wegener.com ...

Manufacturer Wegener Communications Category Switch

Documents that we receive from a manufacturer of a Wegener Communications Unity RF Switch can be divided into several groups. They are, among others:
- Wegener Communications technical drawings
- Unity RF Switch manuals
- Wegener Communications product data sheets
- information booklets
- or energy labels Wegener Communications Unity RF Switch
All of them are important, but the most important information from the point of view of use of the device are in the user manual Wegener Communications Unity RF Switch.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Wegener Communications Unity RF Switch, service manual, brief instructions and user manuals Wegener Communications Unity RF Switch. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Wegener Communications Unity RF Switch.

Similar manuals

A complete manual for the device Wegener Communications Unity RF Switch, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Wegener Communications Unity RF Switch by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Wegener Communications Unity RF Switch.

A complete Wegener Communications manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Wegener Communications Unity RF Switch - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Wegener Communications Unity RF Switch, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Wegener Communications Unity RF Switch, that we can find in the current document
3. Tips how to use the basic functions of the device Wegener Communications Unity RF Switch - which should help us in our first steps of using Wegener Communications Unity RF Switch
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Wegener Communications Unity RF Switch
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Wegener Communications Unity RF Switch in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Wegener Communications Unity RF Switch?

Use the form below

If you did not solve your problem by using a manual Wegener Communications Unity RF Switch, ask a question using the form below. If a user had a similar problem with Wegener Communications Unity RF Switch it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)