English dropdown-ico

Manual Shindaiwa 68006-94310

28 pages 0.84 mb
Download

Go to site of 28

Summary
  • Shindaiwa 68006-94310 - page 1

    SHIND AIWA OWNER’S AND OPERA T OR’S MANU AL EC7500/EC7600 ENGINE CUT OFF SAW WARNING!  Read this manual and familiarize yourself with its contents.  This unit is designed primarily for cutting construction materials and metal ac- cording to the type of cutting wheel installed.  T o minimize the risk of injury to yourself and others, ...

  • Shindaiwa 68006-94310 - page 2

    2 Wheel Rotating Direction Max Spindle Speed/ Rated Spindle Speed Throughout this manual are special “attention statements”. WARNING! A statement preceded by the word “W ARNING” contains informa - tion that should be acted upon to prevent serious injury . CA UTION! A statement preceded by the word “CAUTION” contains information that sho ...

  • Shindaiwa 68006-94310 - page 3

    3 Before Operation  Children and people who do not understand this manual must not use this unit.  Never allow other people or animals to be near the unit when starting or operating.  Never touch a rotating cut-off wheel.  Operate the unit only in a well ventilated area.  Never operate the unit in a closed area such as ...

  • Shindaiwa 68006-94310 - page 4

    4 Safety Precautions (continued) WARNING! Figure 1. Start the engine at least 3 meters from a fueling location. Starting The Engine  Start the engine at least 3 meters away from a fueling location.  When starting the engine, make sure the cut-off wheel does not touch any object or ground. As soon as the engine starts, the cut-off wheel ...

  • Shindaiwa 68006-94310 - page 5

    5 Safety Precautions (continued) WARNING! Kickback  Kickback may force the cut-off wheel up and back toward the operator lightning-fast.  Kickback can occur whenever the upper half of the cut-off wheel touches an object. Never cut an object using the upper half of the cut-off wheel. EC7500.14 EC7500.17 Figure 2. Always be aware of, and ...

  • Shindaiwa 68006-94310 - page 6

    6 Inspection and Maintenance  Before performing any inspection, maintenance, repair or cleaning of the unit, make sure engine and cut-off wheel are completely stopped and cooled down.  Inspection and maintenance operations should be done in a well ventilated location and where there are no combustibles nearby .  When replacing par ...

  • Shindaiwa 68006-94310 - page 7

    7 EC7500.1 N o p e r f o r m a n c e g u a r a n t e e w i t h o u t � u s i n g g e n u i n e S h i n d a i w a b l a d e s � N o - l o a d r e v o l u t i o n s p e e d : 4 1 8 0 m i n - 1 ( r p m ) � U s e r e i n f o r c e d a b r a s i v e b l a d e s w i t h � m a x i m u m u s e a b l e p e r i m e t e r v e l o c i t y o f : � 1 5 ...

  • Shindaiwa 68006-94310 - page 8

    8 EC7500.18 EC7500.1A Unit Description Figure 5 Air Cleaner Cover Choke Primer Pump Front Handle Cylinder Cover Throttle T rigger Lockout Carburetor Idle Adjustment Screw Cut-off Wheel Wheel Guard Lock Knob Belt Guard Rear Handle Fuel Filler Cap Recoil Starter Throttle T rigger Clutch Cover Muffler Decompression V alve ON/OFF Switch ...

  • Shindaiwa 68006-94310 - page 9

    9 T echnical Specifica tions Engine Type ............................ 2-Cycle, vertical-cylinder, air-cooled Displacement ........................ 73.5 cm 3 * Bore x Stroke ...................... 51 x 36mm Max. Power Output ** ................. 3.3kW Recommended Engine Idling Speed ................. 2,500 min -1 (rpm)** Recommended Maximum Engine ...

  • Shindaiwa 68006-94310 - page 10

    10 IMPORT ANT! This unit is equipped with a 22mm wheel collar . Wheel adapters for 20mm and 25.4mm cut-off wheels are located in the tool set. Before mounting a wheel, deter- mine its arbor diameter . If it is necessary to replace the col- lar , remove the snap ring on the arbor , install the correct size arbor collar , and then replace the snap ri ...

  • Shindaiwa 68006-94310 - page 11

    11 EC7500.20 4. Loosen bolt with the wrench and remove bolt and outer flange. See Figure 8. Figure 8 Outer Flange Bolt Tighten Loosen WARNING!  When filling the fuel tank, make sure the engine is stopped and cool.  Filling the fuel tank or mixing fuel and oil must be done in a place where there is no risk of fire. CA UTION! Some gaso ...

  • Shindaiwa 68006-94310 - page 12

    12 EC7500.22 7. Grip the recoil star ter handle with your right hand, pull the star ter cord slowly until you feel the star ter engage, then… 8. …star t the engine by pulling the star ter cor d upward rapidly . CA UTION!  The recoil starter can be dam- aged by abuse.  Never pull the starter cord to its full length.  Always eng ...

  • Shindaiwa 68006-94310 - page 13

    13 If the engine fails to star t, r epeat the appropriate star ting pr ocedure for a cold or war m engine. WARNING! Keep well away from fire! If the engine still does not star t, 1. Pull the choke all way out. 2. Unscrew the knob on the cleaner cover and remove the cleaner cover . See Figure 11. EC7500.23 1. T ur n the on-of f switch On. WARNING! ...

  • Shindaiwa 68006-94310 - page 14

    14 EC7500.27 WARNING!  Never permit bystanders or animals near the unit when starting or operating the unit.  Be aware of kickback! Kickback may force the cut-off wheel up and back toward the operator lightning-fast. Kick- back can occur whenever the upper half of the cut-off wheel touches an object. Never cut an object using the upper- ...

  • Shindaiwa 68006-94310 - page 15

    15 NOTE: For units equipped with a water kit, loosen the (2) water nozzles and dis- connect the main water line from the double nozzle. 1. Remove the cutting wheel (See pages 10 and 11). Using a Phillips screwdriver , loosen the tension screw until the tension indicator is all the way to the front of the scale. See Figure 15. Figure 15 Figure 18 4. ...

  • Shindaiwa 68006-94310 - page 16

    16 Inspection and Maintenance Item What to Do Daily Weekly Monthly As Req’d Air Cleaner Clean  Cut-off Wheel Check & Sharpen  Bolts/Screws Check & Retighten  Fuel Cap Check Leakage  Fuel Tank Check Leakage  Wheel Guard Check Function   Clutch Bearing Grease  Belt Check and Adjust  Spark P ...

  • Shindaiwa 68006-94310 - page 17

    17 EC7500.23 EC7500.24 WARNING! Inspection and maintenance should be done in a well ventilated place and where there is no risk of fire. Dust in the air cleaner will af fect en - gine life. The air filter must be cleaned ever y time you star t operating. Clean the air filter once a day and replace the filter ever y 20 hours of operation accordi ...

  • Shindaiwa 68006-94310 - page 18

    18 EC7500.30 It is not necessar y to adjust the carbu- retor when the unit is new . Adjust the carburetor only when you are sur e it is necessar y due to dif fer ences in work- ing conditions such as atmospheric pressure or temperatur e, or change in unit conditions after more than 10 hours of use. If you are unfamiliar with carbur e - tor adjustme ...

  • Shindaiwa 68006-94310 - page 19

    19 EC7500.34 High and Low Speed Needle The high and low speed needle is fixed and cannot be adjusted. Spar k Plug Maintenance If the engine becomes hard to star t or if idle speed is unstable, inspect the spark plug according to the following procedures. 1. Remove the spark plug. Refer to the procedures on page 13, If the Engine Does Not Star t… ...

  • Shindaiwa 68006-94310 - page 20

    20 EC7500.47 EC7500.36 EC7500.35 Replacing the Driv e Belt 1. Loosen the tension screw . Loosen the two bolts on the belt guard and remove the belt guar d by sliding it to the right. See Figure 26. 2. Loosen the two bolts in the clutch cover and remove the clutch cover . 3. Replace the old belt with a new one. Figure 26 T ension Screw Clutch Cover ...

  • Shindaiwa 68006-94310 - page 21

    21 Replacing the Cut-off W heel 1. Make sure the ignition switch is Of f and the engine is stopped. 2. Inser t a 6mm hex wrench into the hole in the belt guard to pr event the drive shaft from tur ning. See Figure 29. Figure 29 Outer Flange 3. Loosen the outer flange bolt with the wrench and remove the bolt and outer flange. 4. Before mounting a ...

  • Shindaiwa 68006-94310 - page 22

    22 EC7500.44 Shar pening a Diamond Cut-off W heel While r unning the engine at low speed, make about 10 passes at cutting a con- crete block or a soft brick. Keep the block watered while sharpening. Checking the Fuel Filter WARNING! KEEP AW A Y FROM FIRE OR EXCESS HEA T! 1. Remove the fuel filler cap. 2. Take the filter out from the fuel opening ...

  • Shindaiwa 68006-94310 - page 23

    23 Whenever the unit will not be used for 30 days or longer , use the following procedures to pr epare if for storage:  Clean exter nal par ts thoroughly .  Drain all the fuel from the carbure- tor and the fuel tank. IMPORT ANT! All stored fuels should be stabilized with a fuel stabilizer such as StaBil™. To remove the remaining fuel ...

  • Shindaiwa 68006-94310 - page 24

    24 The engine does not star t. PROBLEM Remov e the spar k plug (pg 13). Is the spark � plug wet? Cutting perf ormance is poor . PROBLEM Make sure the chok e is � pushed fully in. Make sure the air � cleaner is clean (pg 17). Make sure the driv e belt is � properly tightened (pg 19). Make sure the carb uretor is � is properly adjusted (pg ...

  • Shindaiwa 68006-94310 - page 25

    25 DECLARA TION OF CONFORMITY W e hereby declar e the Shindaiwa Cut-of f Machine, Model EC7500 (EC7500/EC1, EC7600/EC1). meets the following respective requir ements. Council Directives: Standard taken: 89/336/EEC as amended EN 292 par ts 1&2 98/37/EC as amended EN 1454 2000/14/EC as amended CISPR 12 2004/26/EC as amended Measured sound power l ...

  • Shindaiwa 68006-94310 - page 26

    26 Notes: ...

  • Shindaiwa 68006-94310 - page 27

    27 Notes: ...

  • Shindaiwa 68006-94310 - page 28

    Shindaiwa Inc. 11975 SW Her man Road T ualatin, Oregon 97062 Telephone 503-692-3070 Fax 503-692-6696 www .shindaiwa.com Shindaiwa Kogyo Co., Ltd. 6-2-11 Ozuka-Nishi Asaminami-Ku, Hiroshima 731-3167, Japan Telephone 81-82-849-2220 Fax 81-82-849-2481 ©2004 Shindaiwa Inc. Part Number 68006-94310 Shindaiwa is a registered trademark of Shindaiwa Inc. ...

Manufacturer Shindaiwa Category Saw

Documents that we receive from a manufacturer of a Shindaiwa 68006-94310 can be divided into several groups. They are, among others:
- Shindaiwa technical drawings
- 68006-94310 manuals
- Shindaiwa product data sheets
- information booklets
- or energy labels Shindaiwa 68006-94310
All of them are important, but the most important information from the point of view of use of the device are in the user manual Shindaiwa 68006-94310.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Shindaiwa 68006-94310, service manual, brief instructions and user manuals Shindaiwa 68006-94310. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Shindaiwa 68006-94310.

Similar manuals

A complete manual for the device Shindaiwa 68006-94310, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Shindaiwa 68006-94310 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Shindaiwa 68006-94310.

A complete Shindaiwa manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Shindaiwa 68006-94310 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Shindaiwa 68006-94310, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Shindaiwa 68006-94310, that we can find in the current document
3. Tips how to use the basic functions of the device Shindaiwa 68006-94310 - which should help us in our first steps of using Shindaiwa 68006-94310
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Shindaiwa 68006-94310
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Shindaiwa 68006-94310 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Shindaiwa 68006-94310?

Use the form below

If you did not solve your problem by using a manual Shindaiwa 68006-94310, ask a question using the form below. If a user had a similar problem with Shindaiwa 68006-94310 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)