English dropdown-ico

Manual Shindaiwa EC7600

28 pages 0.43 mb
Download

Go to site of 28

Summary
  • Shindaiwa EC7600 - page 1

    N o p e r f o r m a n c e g u a r a n t e e w i t h o u t u s i n g g e n u i n e S h i n d a i w a b l a d e s . N o - l o a d r e v o l u t i o n s p e e d : 4 1 8 0 m i n - 1 ( r p m ) U s e r e i n f o r c e d a b r a s i v e b l a d e s w i t h m a x i m u m u s e a b l e p e r i m e t e r v e l o c i t y o f 2 4 8 f t / s e c . U S E O N L Y ...

  • Shindaiwa EC7600 - page 2

    2 Throughout this manual are special “attention statements”. WARNING! A statement preceded by the word “WARNING” contains information that should be acted upon to prevent serious injury. CAUTION! A statement preceded by the word “CAUTION” contains information that should be acted upon to prevent unit damage. IMPORTANT! A statement prece ...

  • Shindaiwa EC7600 - page 3

    3 Before Operation ■ Children and people who do not understand this manual must not use this unit. ■ Never allow other people or animals to be near the unit when starting or operating. ■ Never touch a rotating cut-off wheel. ■ Operate the unit only in a well ventilated area. ■ Never operate the unit in a closed area such as a room, wareho ...

  • Shindaiwa EC7600 - page 4

    4 Safety Precautions (continued) WARNING! Figure 1. Start the engine at least 10 feet (3 meters) from a fueling location. Starting The Engine ■ Start the engine at least 10 feet (3m) away from a fueling location. ■ When starting the engine, make sure the cut-off wheel does not touch any object or ground. As soon as the engine starts, the cut-of ...

  • Shindaiwa EC7600 - page 5

    5 Safety Precautions (continued) WARNING! Kickback ■ Kickback may force the cut-off wheel up and back toward the operator lightning-fast. ■ Kickback can occur whenever the upper half of the cut-off wheel touches an object. Never cut an object using the upper half of the cut-off wheel. EC7500.14 EC7500.17 Figure 2. Always be aware of, and prepar ...

  • Shindaiwa EC7600 - page 6

    6 Inspection and Maintenance ■ Before performing any inspection, maintenance, repair or cleaning of the unit, make sure engine and cut-off wheel are completely stopped and cooled down. ■ Inspection and maintenance operations should be done in a well ventilated location and where there are no combustibles nearby. ■ When replacing parts, always ...

  • Shindaiwa EC7600 - page 7

    7 Safety and Operation Information Labels EC7500.1 N o p e r f o r m a n c e g u a r a n t e e w i t h o u t u s i n g g e n u i n e S h i n d a i w a b l a d e s N o - l o a d r e v o l u t i o n s p e e d : 4 1 8 0 m i n - 1 ( r p m ) U s e r e i n f o r c e d a b r a s i v e b l a d e s w i t h m a x i m u m u s e a b l e p e r i m e t e r v e l ...

  • Shindaiwa EC7600 - page 8

    8 EC7500.18 EC7500.1A Unit Description Figure 5 Air Cleaner Cover Choke Primer Pump Front Handle Cylinder Cover Throttle Trigger Lockout Carburetor Idle Adjustment Screw Cut-off Wheel Wheel Guard Lock Knob Belt Guard Rear Handle Fuel Filler Cap Recoil Starter Throttle Trigger Clutch Cover Muffler Decompression Valve ON/OFF Switch ...

  • Shindaiwa EC7600 - page 9

    9 T echnical Specifications Engine Type ........................... 2-Cycle, vertical-cylinder, air-cooled Displacem ent ....... 4.5 cu. in. (73.5cc)* Bore x Stroke .. 2 x 1.4 in. (51 x 36mm) Max. Power Outpu t ** . . 4.5 hp (3.3kW) Recommended Engine Idling Speed ................ 2,500 min -1 (rpm)** Recommended Maximum Engine Speed ............. ...

  • Shindaiwa EC7600 - page 10

    10 EC7500.20A Assembly EC7500.19 Figure 6 Instruction Manual Engine Unit Tool Set Figure 7. Belt Guard Hex Wrench Mounting the Cut-off Wheel 1. Select a cut-off wheel for your work according to the following chart. Refer to the wheel manufacturer’s manual for additional information. Recommended Cut-off Wheels Inner bore: 0.78" (20mm), 0.86&q ...

  • Shindaiwa EC7600 - page 11

    11 EC7500.20 4. Loosen bolt with the wrench and remove bolt and outer flange. See Figure 8. Figure 8 Outer Flange Bolt Tighten Loosen WARNING! ■ When filling the fuel tank, make sure the engine is stopped and cool. ■ Filling the fuel tank or mixing fuel and oil must be done in a place where there is no risk of fire. CAUTION! Some gasolines cont ...

  • Shindaiwa EC7600 - page 12

    12 EC7500.22 7. Grip the recoil starter handle with your right hand, pull the starter cord slowly until you feel the starter engage, then… 8. …start the engine by pulling the starter cord upward rapidly. CAUTION! ■ The recoil starter can be damaged by abuse. ■ Never pull the starter cord to its full length. ■ Always engage the starter bef ...

  • Shindaiwa EC7600 - page 13

    13 EC7500.23 1. Turn the on-off switch On. WARNING! The cut-off wheel must not rotate at idle speed. If it rotates, reduce idle speed by adjusting the idle adjust screw. 2. Push the decompression valve in. 3. Pull the choke all the way out and push it back to the original position (choke open). The throttle is automatically set at a fast idle posit ...

  • Shindaiwa EC7600 - page 14

    14 EC7500.27 WARNING! ■ Never permit bystanders or animals near the unit when starting or operating the unit. ■ Be aware of kickback! Kickback may force the cut-off wheel up and back toward the operator lightning-fast. Kick- back can occur whenever the upper half of the cut-off wheel touches an object. Never cut an object using the upper- half ...

  • Shindaiwa EC7600 - page 15

    15 NOTE: For units equipped with a water kit, loosen the (2) water nozzles and disconnect the main water line from the double nozzle. 1. Remove the cutting wheel (See pages 10 and 11). Using a Phillips screwdriver, loosen the tension screw until the tension indicator is all the way to the front of the scale. See Figure 15. Figure 15 Figure 18 4. Re ...

  • Shindaiwa EC7600 - page 16

    16 Inspection and Maintenance Item What to Do Daily Weekly Monthly As Req’d Air Cleaner Clean ✔ Cut-off Wheel Check & Sharpen ✔ Bolts/Screws Check & Retighten ✔ Fuel Cap Check Leakage ✔ Fuel Tank Check Leakage ✔ Wheel Guard Check Function ✔ Clutch Bearing Grease ✔ Belt Check and Adjust ✔ Spark Plug Check and Clean ✔ Cyli ...

  • Shindaiwa EC7600 - page 17

    17 EC7500.23 EC7500.24 WARNING! Inspection and maintenance should be done in a well ventilated place and where there is no risk of fire. Dust in the air cleaner will affect engine life. The air filter must be cleaned every time you start operating. Clean the air filter once a day and replace the filter every 20 hours of operation according to the f ...

  • Shindaiwa EC7600 - page 18

    18 EC7500.30 It is not necessary to adjust the carburetor when the unit is new. Adjust the carburetor only when you are sure it is necessary due to differ- ences in working conditions such as atmospheric pressure or temperature, or change in unit conditions after more than 10 hours of use. If you are unfamiliar with carbure- tor adjustment techniqu ...

  • Shindaiwa EC7600 - page 19

    19 EC7500.34 High and Low Speed Needle The high and low speed needle is fixed and cannot be adjusted. Spark Plug Maintenance If the engine becomes hard to start or if idle speed is unstable, inspect the spark plug according to the following procedures. 1. Remove the spark plug. Refer to the procedures on page 13, If the Engine Does Not Start… 2. ...

  • Shindaiwa EC7600 - page 20

    20 EC7500.47 EC7500.36 EC7500.35 Replacing the Drive Belt 1. Loosen the tension screw. Loosen the two bolts on the belt guard and remove the belt guard by sliding it to the right. See Figure 26. 2. Loosen the two bolts in the clutch cover and remove the clutch cover. 3. Replace the old belt with a new one. Figure 26 Tension Screw Clutch Cover Bolt ...

  • Shindaiwa EC7600 - page 21

    21 Replacing the Cut-off Wheel 1. Make sure the ignition switch is Off and the engine is stopped. 2. Insert a 6mm hex wrench into the hole in the belt guard to prevent the drive shaft from turning. See Figure 29. Figure 29 Outer Flange 3. Loosen the outer flange bolt with the wrench and remove the bolt and outer flange. 4. Before mounting a cut-off ...

  • Shindaiwa EC7600 - page 22

    22 EC7500.44 Sharpening a Diamond Cut-off Wheel While running the engine at low speed, make about 10 passes at cutting a concrete block or a soft brick. Keep the block watered while sharpening. Checking the Fuel Filter WARNING! KEEP AWAY FROM FIRE OR EXCESS HEAT! 1. Remove the fuel filler cap. 2. Take the filter out from the fuel opening by using a ...

  • Shindaiwa EC7600 - page 23

    23 Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare if for storage: ■ Clean external parts thoroughly. ■ Drain all the fuel from the carbure- tor and the fuel tank. IMPORTANT! All stored fuels should be stabilized with a fuel stabilizer such as StaBil™. To remove the remaining fuel from the fue ...

  • Shindaiwa EC7600 - page 24

    24 The engine does not star t. PROBLEM Remov e the spar k plug (pg 13). Is the spark plug wet? Cutting perf or mance is poor . PROBLEM Make sure the chok e is pushed fully in. Make sure the air cleaner is clean (pg 17). Make sure the driv e belt is properly tightened (pg 19). Make sure the carb uretor is is properly adjusted (pg 18). Make sure the ...

  • Shindaiwa EC7600 - page 25

    25 Shindaiwa Kogyo Co., Ltd. Federal Emission Design And Defect Limited Warranty Utility And Lawn And Garden Engines Shindaiwa Kogyo Co., Ltd. warrants to the initial purchaser and each subsequent owner, that this utility equipment engine (herein engine) is designed, built and equipped to conform at the time of initial sale, to all applicable regul ...

  • Shindaiwa EC7600 - page 26

    26 PARTS COVERED Listed below are the parts covered by the Federal Emission Design and Defect Warranty. Some parts listed below may require scheduled maintenance and are warranted up to the first scheduled replacement of that part. The warranted parts include: 1. Carburetor Internal Components • Valve Assembly-throttle, Jet, Metering Diaphram 2. ...

  • Shindaiwa EC7600 - page 27

    27 MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA KOGYO CO., LTD. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMP ...

  • Shindaiwa EC7600 - page 28

    Shindaiwa Inc. 11975 SW Herman Road Tualatin, Oregon 97062 Telephone 503-692-3070 Fax 503-692-6696 www.shindaiwa.com Shindaiwa Kogyo Co., Ltd. 6-2-11 Ozuka-Nishi Asaminami-Ku, Hiroshima 731-3167, Japan Telephone 81-82-849-2220 Fax 81-82-849-2481 ©2002 Shindaiwa Inc. Part Number 68002-94310 Shindaiwa is a registered trademark of Shindaiwa Inc. ...

Manufacturer Shindaiwa Category Saw

Documents that we receive from a manufacturer of a Shindaiwa EC7600 can be divided into several groups. They are, among others:
- Shindaiwa technical drawings
- EC7600 manuals
- Shindaiwa product data sheets
- information booklets
- or energy labels Shindaiwa EC7600
All of them are important, but the most important information from the point of view of use of the device are in the user manual Shindaiwa EC7600.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Shindaiwa EC7600, service manual, brief instructions and user manuals Shindaiwa EC7600. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Shindaiwa EC7600.

Similar manuals

A complete manual for the device Shindaiwa EC7600, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Shindaiwa EC7600 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Shindaiwa EC7600.

A complete Shindaiwa manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Shindaiwa EC7600 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Shindaiwa EC7600, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Shindaiwa EC7600, that we can find in the current document
3. Tips how to use the basic functions of the device Shindaiwa EC7600 - which should help us in our first steps of using Shindaiwa EC7600
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Shindaiwa EC7600
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Shindaiwa EC7600 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Shindaiwa EC7600?

Use the form below

If you did not solve your problem by using a manual Shindaiwa EC7600, ask a question using the form below. If a user had a similar problem with Shindaiwa EC7600 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)