-
Kathrein UFS 902 - page 1
Operating Manual HDTV receiver for satellite reception UFS 902 ...
-
Kathrein UFS 902 - page 2
2 FOREWORD/IMPORT ANT INFORMA TION Dear customer , this Operating Manual is intended to help you make the fullest use of the extensive range of functions offered by your new HDTV satellite receiver . We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible. T o help you understand p ...
-
Kathrein UFS 902 - page 3
3 FOREWORD/IMPORT ANT INFORMA TION The channels available on the satellites and transponders are subject to continual change. In such cases, it is necessary to re-adjust the channels as the factory preset programming corresponds to the situation on the date of manufacture. The information for these settings can be found on the Internet or in releva ...
-
Kathrein UFS 902 - page 4
4 RECEIVER FEA TURES/PRODUCT P ACKAGE - Receiver UFS 902 (silver or black) - Infra-red remote control - Batteries - HDMI cable - Operating manual - Safety instructions - Scart cable - Mains power cable PRODUCT P ACKAGE The UFS 902 HDTV receiver is suitable for the reception of digital satellite TV and radio channels. The receiver can be used to rec ...
-
Kathrein UFS 902 - page 5
5 CONTENTS FOREWORD/IMPORT ANT INFORMA TION .................................................................................. 2 RECEIVER FEA TURES/PRODUCT P ACKAGE ............................................................................ 4 CONTENTS ................................................................................................. ...
-
Kathrein UFS 902 - page 6
6 SAFETY INSTRUCTIONS - IMPORT ANT INFORMA TION DANGER! W ARNING! CAUTION! GB Safety Instructions – Important Information This page contains important information about the operation, installation location and connection of the unit. Read these instructions carefully before starting to use the unit. Mains cable Make sure that the mains cable (pow ...
-
Kathrein UFS 902 - page 7
7 CONTROLS, DISPLA YS AND CONNECTIONS This section provides a brief description of all the controls, displays and connections. The button symbols presented here can also be found in the description of the operating steps. USB 2.0 5V... 500 mA max Front panel controls and displays 1. Common Interface for one CA module for pay TV cards * ) (behind th ...
-
Kathrein UFS 902 - page 8
8 CONNECTION AND SETUP The following section is intended speci fi cally for specialist dealers. Y ou need not refer to this section unless you are carrying out the installation yourself. The “Connection Examples” section provides a sample con fi guration. Do not connect the receiver to the power supply until all installation work has been pro ...
-
Kathrein UFS 902 - page 9
9 CONNECTION AND SETUP Connect the satellite receiver (HDMI or alternatively TV Scart socket) and the TV set using a HDMI or Scart cable (see “Connection Example”). If your TV is stereo, you can receive the sound in stereo via the HDMI or Scart connection. For system reasons, the same video signals are to be found at the TV Scart socket as at t ...
-
Kathrein UFS 902 - page 10
10 REMOTE CONTROL Sound on/off ... Enter numbers for channels, timer etc. Open main menu, leave the menu and return to the TV picture (red) Open favourites selection ! (green) 1x open display of 4:3 programmes, 2x open HDMI/YUV format % V olume Leave menu step by step Change channel in the programme preview (EPG) Current ...
-
Kathrein UFS 902 - page 11
11 REMOTE CONTROL REMOTE CONTROL RC 660 The RC 660 remote control supports up to four units which are supplied as standard with the RC 660. First switch off all other receivers at the power switch. 1. Set-up using menu On the UFS 902 the remote control code on the “Service Menu”, “Remote Control Code” menu is changed. Note: The remote contr ...
-
Kathrein UFS 902 - page 12
12 FIRST INST ALLA TION Before using your receiver for the fi rst time, read the “Safety Instructions” and “Connection and Setup” sections. The “Connection Examples” section provides a sample con fi guration. Do not connect the receiver to the power supply until all installation work has been properly carried out. The guidance given i ...
-
Kathrein UFS 902 - page 13
13 The following display appears: Use the buttons here to select the settings for your TV set. When doing this, refer to the operating instructions for your TV set! Video Output via Select here the connection on the receiver to which you have connected your television. Either SCART or HDMI/YUV FIRST INST ALLA TION TV aspect ratio Here ...
-
Kathrein UFS 902 - page 14
14 FIRST INST ALLA TION System Select the setting here to match your reception system using the buttons. Y ou have the following options: - DiSEqC™1.0 - One Cable - LNB only If your reception system supports DiSEqC™, in “System” select “DiSEqC™1.0” (is used for switch- over from one received satellite to another). If your recep ...
-
Kathrein UFS 902 - page 15
15 Number of Satellites Use the buttons to select how many satellites (max. 4) you would like to receive with your reception system. The following display appears (example): FIRST INST ALLA TION: DiSEqC™1.0 Use the buttons to select the fi rst satellite slot. Press to open the menu for the satellite settings. The following disp ...
-
Kathrein UFS 902 - page 16
16 FIRST INST ALLA TION: DiSEqC™1.0 LNB T ype Here use the buttons to select the LNB type used in your system. The choice is between “Universal” and “user-de fi ned”. Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB. user-de fi ned: If you choose not to use a universal L ...
-
Kathrein UFS 902 - page 17
17 FIRST INST ALLA TION: LNB ONL Y Satellite and Position Use the buttons to select the desired satellite whose signal is to be received by the tuner . When you have selected your desired satellite, use the buttons to switch to the selection of the “LNB T ype”. LNB T ype Here use the buttons to select the LNB type used in y ...
-
Kathrein UFS 902 - page 18
18 FIRST INST ALLA TION: LNB ONL Y user-de fi ned: If you choose not to use a universal LNB, you must here set the frequency ranges for which your LNB was con fi gured. Use the buttons to select the frequency range to be changed (low , high or limit frequency). Use the buttons or the number buttons to set the exact frequency for whi ...
-
Kathrein UFS 902 - page 19
19 FIRST INST ALLA TION: One Cable Use the buttons here to select “One Cable” as the “System”. Press the button to move to the next menu item. The following display appears: Number of Satellites Use the buttons to select how many satellites (max. 2) you would like to receive with your reception system. Press the button ...
-
Kathrein UFS 902 - page 20
20 Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB. Wideband: No further input is necessary , since all frequency ranges are set by the Wideband LNB. user-de fi ned: If you are not using a Universal or a Wideband system, you must set the frequencies here. Y ou can fi nd the necessary in ...
-
Kathrein UFS 902 - page 21
21 FIRST INST ALLA TION: Single-cable system (automatic) The receiver searches for the transmission channels on your single-cable system and shows in the next display the available transmission channels. Use the buttons to select the transmission channel you want and con fi rm the selection with the button. The receiver now reads the ex ...
-
Kathrein UFS 902 - page 22
22 Connected equipment Use the buttons to select the type of system to which they are connected or the single-cable system components fi tted (refer to the manuals, instructions and notes for the system and the system components). Available options: - user-de fi ned - KA THREIN UAS 481 (single-cable feed system, max. four receivers) - KA T ...
-
Kathrein UFS 902 - page 23
23 Secure channel with PIN If your single-cable system allows the transmission frequency to be protected by entering a PIN, this is the menu for de fi ning the PIN. No other receiver can then use that transmission frequency unless the PIN is input. Select the setting “Y es” using the buttons. A line with the text “Password PIN” is t ...
-
Kathrein UFS 902 - page 24
24 Selection “UAS 481” or “EXR 551” T ransmission channel Use the buttons to select a free available transmission channel. A maximum of four transmission channels are available (1400, 1516, 1632 and 1748 MHz). T est connection When you have set a free transmission channel, press the buttons to switch to the “T est connection ...
-
Kathrein UFS 902 - page 25
25 Selection “EXR 552” T ransmission channel Use the buttons to select a free available transmission channel. A maximum of two transmission channels are available (1400 and 1516 MHz). T est connection When you have set a free transmission channel, press the buttons to switch to the “T est connection” selection fi eld and pres ...
-
Kathrein UFS 902 - page 26
26 FIRST INST ALLA TION: Single-cable system (manual) Selection “EXU 908” T ransmission channel Use the buttons to select a free available transmission channel. A maximum of eight transmission channels are available (1284, 1400, 1516, 1632, 1748, 1864, 1980 and 2096 MHz). Secure channel with PIN The EXU 908 single-cable matrix allows the ...
-
Kathrein UFS 902 - page 27
27 Execute Channel search Use the buttons to select (yes or no) whether you wish to start a channel search. It is not essential to start a channel search; instead you can use the factory pre-programmed channels. However the channels do change from time to time (e.g. their frequencies change), which the receiver does not automatically detect, ...
-
Kathrein UFS 902 - page 28
28 Local time offset (UTC) Use the buttons to set the time zone variation from UTC (formerly GMT) (e.g. for Germany +1 hour). Use the buttons to switch to the “Automatic clock change” fi eld. Use the buttons to select whether the receiver should automatically change over between summer and winter time. If “On” is selec ...
-
Kathrein UFS 902 - page 29
29 OPERA TING INSTRUCTIONS The structure of the menu concept is based on logical operating sequences. The programme showing on the current selected channel always appears in the top right-hand corner of the screen. Y ou will fi nd detailed descriptions of the selected menu items in the relevant sections of the operating manual! Note: The selected ...
-
Kathrein UFS 902 - page 30
30 MENU TREE OPERA TING INSTRUCTIONS Main menu Open using the button ...
-
Kathrein UFS 902 - page 31
31 OPERA TING INSTRUCTIONS The language for the on-screen display is set as follows: → → Language Setting → → → English → Available options: German, English, French, Italian, Spanish, Czech, Dutch, Polish, Turkish and Russian. After you have performed the settings, press the or the button to exit the ma ...
-
Kathrein UFS 902 - page 32
32 ON-SCREEN DISPLA YS (OSD) The channel OSD is displayed for a few seconds each time the channel is changed (this feature can be changed on the “Settings”, “Customize Screen Menu” menu) or displayed continuously by pressing the button. The OSD for the current radio channel has the same layout. Channel name Channel number from the overa ...
-
Kathrein UFS 902 - page 33
33 If the channel OSD contains the following icon , this is a portal channel. Press the " (yellow) button to display the channels available on this portal (such as matches on a speci fi c day of play). In this example three “sub-channels” are available for selection within this portal channel. Select the channel using the and b ...
-
Kathrein UFS 902 - page 34
34 Press the button to open the channel list. When you open this list the channel list selection / sort order is displayed from where you selected the last channel. At the top left you will see the selected channel list (TV Channel or Radio Channel) displayed. Press the # (blue) button to switch between the TV and radio channel lists. Underneat ...
-
Kathrein UFS 902 - page 35
35 Selection and sorting options: - Press the (red) button to open the favourite list selection. The buttons allow you to scroll through the existing favourite lists. - Press the ! (green) button to return to the overall list (all satellites). Use the buttons to choose between the received satellites (display all channels from a satel ...
-
Kathrein UFS 902 - page 36
36 EPG - ELECTRONIC PROGRAMME GUIDE OPENING THE EPG The EPG is opened by pressing the button. Each time the EPG is opened, you will automatically be shown the “Current” view , irrespective of which view you were shown the last time you left the EPG. The following display appears (example): Channel number from the overall list, channel name, ...
-
Kathrein UFS 902 - page 37
37 EPG - ELECTRONIC PROGRAMME GUIDE Selection options: - (red) button Open the timer list (display of all pre-programmed recordings) - button Jump the “Current” view forwards by 15 minutes - " (yellow) button Open a preview of the currently highlighted channel - # (blue) button Open the category selection (sorting the programs by categ ...
-
Kathrein UFS 902 - page 38
38 “PREVIEW” VIEW (PROGRAMME MAGAZINE) The “Preview” view (programme magazine) can be opened at any time in EPG by pressing the " (yellow) button. EPG - ELECTRONIC PROGRAMME GUIDE In the “Preview” view you will see all the programmes that will be shown in the previous “Current” list of selected channels. Provided that EPG data ...
-
Kathrein UFS 902 - page 39
39 EPG - ELECTRONIC PROGRAMME GUIDE CA TEGORIES VIEW The “Categories” view can be opened at any time in EPG by pressing the # (blue) button. In the “Categories” view you can see all programmes sorted by category and starting time. The following categories are available for selection: Movies, Series, Sport, Program for kids, Entertainment, C ...
-
Kathrein UFS 902 - page 40
40 SEARCH FUNCTION The search function can be opened at any time in EPG by pressing the button. The search function allows you to search for programmes based on their additional information or their name. Use the number buttons to enter the desired search expression (see also “Operating Instructions” “Alphanumeric Entries”). When you ha ...
-
Kathrein UFS 902 - page 41
41 EPG - ELECTRONIC PROGRAMME GUIDE ADDITIONAL INFORMA TION (i BUTTON) The additional information can always be opened by pressing the button whenever the “i symbol” appears in front of the programme name (see screenshot on the right). First however the channel must be selected. The following display appears (example): The additional inform ...
-
Kathrein UFS 902 - page 42
42 RECORDING (TIMER) The (red dot) button allows you to set up a programme at any time for recording on an external recorder . The programme to be recorded can be selected in any of the EPG views, provided the (red dot) button appears at the bottom of the screen display . Programme present in the EPG: Select the desired programme and press ...
-
Kathrein UFS 902 - page 43
43 EPG - ELECTRONIC PROGRAMME GUIDE RECORDING ONCE ONL Y Use the buttons to select the recording mode “once” (see screenshot “Recording (timer)” section). Use the buttons to switch to the selection fi eld “Date” and use the buttons to select the desired recording day . Use the buttons to switch to the select ...
-
Kathrein UFS 902 - page 44
44 RECORDING WEEKL Y Use the buttons to select the recording mode “weekly” (see screenshot below). Use the buttons to switch to the selection fi eld “Start” and use the buttons or the number buttons to select the desired recording start time. Use the buttons to switch to the selection fi eld “End” and use t ...
-
Kathrein UFS 902 - page 45
45 Use the buttons to switch to the selection fi eld “End” and use the buttons or the number buttons to select the desired recording end time. When all settings have been made, press the button to save the recording settings. Y ou can view the scheduled recording in the timer list view of the EPG (see section “T imer list? ...
-
Kathrein UFS 902 - page 46
46 EPG - ELECTRONIC PROGRAMME GUIDE TIMER LIST VIEW The “T imer list” view can be opened at any time in EPG by pressing the (red) button. The timer list view shows you all the recordings that are scheduled. The buttons allow the recordings to be sorted into “once” or “repeated” recordings. The cursor buttons ( ) allo ...
-
Kathrein UFS 902 - page 47
47 COMMON INTERF ACE Always follow the operating instructions from your pay TV provider and the instructions supplied with the Smartcard and the CA module! Smartcards and CA module are not included with this product! The cards and modules are issued by the respective pay TV providers, and contain the subscriber data and details of the channels for ...
-
Kathrein UFS 902 - page 48
48 Y ou can fi nd out which Conditional Access module is in the CI slot on the UFS 902 and which Smartcard is in which CA module from the “Mainmenu” under “Settings”, and the “Common Interface” menu. Con fi rmation is by pressing the button. Press the button. Y ou will then see the menu generated by the CA module. The screensh ...
-
Kathrein UFS 902 - page 49
49 TELETEXT When you press the button, the receiver processes the broadcast Videotext/T eletext service, if available, for your TV set to display , even when the signal is encrypted. During the search, the page which is being searched for is displayed in the top left-hand corner with the time and date displayed at the top right. When the search ...
-
Kathrein UFS 902 - page 50
50 EDITING CHANNEL LIST Select the “Edit TV -Channellist” menu using the menu button , the buttons on the main menu and . SELECTION OF THE LIST/CHANNEL T O BE EDITED Press the # (blue) button to switch between the TV and radio channel lists. Radio channels are edited in the same way as TV channels. Editing favourite lists is expl ...
-
Kathrein UFS 902 - page 51
51 EDITING LIST/CHANNELS When you have selected the channel or channel list to be edited, press the (red dot) button to open the edit menu. Y ou have the following edit options: - Move: Channel can be moved within the current list to another channel slot - Delete: Delete the channel from the current list - Skip: Channel will be skipped when zap ...
-
Kathrein UFS 902 - page 52
52 DELETING CHANNELS Use the buttons to select the channel to be deleted on the channel list you have selected. Press the button to open the edit menu and use the buttons to select the “Delete” function. Con fi rm the command by pressing the button. EDITING CHANNEL LIST SKIPPING CHANNELS Use the buttons to select t ...
-
Kathrein UFS 902 - page 53
53 LOCKING CHANNELS Use the buttons to select the channel to be locked on the channel list you have selected. Press the button to open the edit menu and use the buttons to select the “Lock” function. Con fi rm the command by pressing the button. Y ou are now prompted to enter the PIN code (factory default setting: 0000). ...
-
Kathrein UFS 902 - page 54
54 EDITING CHANNEL LIST EDITING F A VOURITE LISTS When you have selected the favourite list to be edited (open using the (red) button and select using the buttons), press the (red dot) button to open the edit menu. Y ou have the following edit options: - Remove from favoritelist: The channel will be removed from the favourite list - Lock ...
-
Kathrein UFS 902 - page 55
55 LOCKING CHANNELS Use the buttons to select the channel to be locked on the favourite list you have selected. Press the button to open the edit menu and use the buttons to select the “Lock” function. Con fi rm the command by pressing the button. Y ou are now prompted to enter the PIN code (factory default setting: 0000) ...
-
Kathrein UFS 902 - page 56
56 SEARCHING FOR CHANNELS (CHANNEL SEARCH) Select the “Search Channels” menu using the menu button , the buttons on the main menu and . Y ou have three options for a channel search. - Automatic Channel Search - all transponders for the satellite you selected will be searched - Manual Channel Search - only the selected transponder ...
-
Kathrein UFS 902 - page 57
57 Satellite Select the satellite to be searched, using the buttons. Make sure your reception system is aligned to the selected satellite. Y ou can search only one satellite at a time. If you have connected a multi-feed reception system (e.g. reception of ASTRA 19.2° East and HOTBIRD 13° East), you must repeat this procedure once for each ...
-
Kathrein UFS 902 - page 58
58 Newly found channels are identi fi ed with the designation “New” after the channel name. After completion of the search, you will see the following message (example): Press the button. Y ou will be asked whether you wish to save the changes or not. Selection is performed using the buttons and is con fi rmed using the button. ...
-
Kathrein UFS 902 - page 59
59 SEARCHING FOR CHANNELS (CHANNEL SEARCH) The buttons allow you to select different sets of parameters for the search. Satellite Use the buttons to select the satellite on which the transponder you wish to search is located. Make sure your reception system is aligned to the selected satellite. Y ou can search only one transponder at ...
-
Kathrein UFS 902 - page 60
60 Network Search Use the buttons (On/Off) to select whether a network search should be performed. If you set the network search to “Off”, only the factory stored transponders of the satellites you previously selected will be searched for new as yet unlisted channels. If you set the network search to “On”, the transponder network ena ...
-
Kathrein UFS 902 - page 61
61 Press the button to move to the next selection item. T ransponder Frequency Use the buttons (transponder frequency already saved) or the number buttons (transponder frequency not yet saved) to select the transponder frequency on which the channel being sought is transmitted. At the bottom right of the screen display , the receiver sho ...
-
Kathrein UFS 902 - page 62
62 P ARENT AL CONTROL Select the “Parental Control” menu using the menu button , the buttons on the main menu and . Y ou are now prompted to enter the PIN code (factory default setting: 0000). After entering the PIN using the number buttons the following display appears: Select the parameters to be changed using the button ...
-
Kathrein UFS 902 - page 63
63 SETTINGS The selected menus, sub-menus and positions, as well as the parameters to be set, are each highlighted in colour . The menus are largely self-explanatory . Pay attention to the bar at the bottom of the on-screen display . These provide information on what to do next. Select the “Settings” menu using the menu button , the ...
-
Kathrein UFS 902 - page 64
64 TV SETTINGS SETTINGS Use the buttons here to select the settings for your TV set. When doing this, refer to the operating instructions for your TV set! Video Output via Select here the connection on the receiver to which you have connected your television. Either TV aspect ratio Here you select the TV's picture format. Either - ...
-
Kathrein UFS 902 - page 65
65 Auto Dolby Digital OUTPUT Here you can select whether the receiver should automatically output the Dolby Digital signal (if this is transmitted). Audio Delay (setting not currently available!) Here you can set a delay in milliseconds, if the sound output from your receiver is out of synch with the TV picture (lip synchronicity). The delay can be ...
-
Kathrein UFS 902 - page 66
66 SETTINGS Use the buttons to select the time after which you want the channel OSD to disappear automatically . The selections available are “Off”, 1, 2, 3, 4, 5 or 6 Seconds. CHANNEL OSD DURA TION Use the buttons (On/Off) to specify whether the volume bar is displayed when adjusting the volume. DISPLA Y VOLUME BAR Use the ...
-
Kathrein UFS 902 - page 67
67 SETTINGS DA TE AND TIME COMMON INTERF ACE See “Common Interface” section ANTENNA CONFIGURA TION See “First Installation” section, pages 14ff Local time offset (UTC) Use the buttons to set the time zone variation from UTC (formerly GMT) (e.g. for Germany +1 hour). Use the buttons to switch to the “Automatic clock change” ...
-
Kathrein UFS 902 - page 68
68 SER VICE MENU Select the “Service” menu using the menu button , the buttons on the main menu and . The following display appears: Current software version Last update run SOFTW ARE UPDA TE Y ou can also check manually whether new software is available. Use the buttons to switch to “Software Update“ and then press th ...
-
Kathrein UFS 902 - page 69
69 SER VICE MENU Also note the bars at the bottom of the on-screen display! These provide information on what to do next. Updating software If new software is available (but only then), use the buttons (No/Y es) to select whether you wish to load the new software that is available. If you are unsure whether you wish to load the new software, ...
-
Kathrein UFS 902 - page 70
70 F ACTOR Y RESET Select the “Service” menu using the menu button , the buttons on the main menu and . Use the buttons to switch to “Factory Reset” and press the button. The following display appears: Press the button to load the factory default settings. The channels and favourite lists remain unchanged. SER ...
-
Kathrein UFS 902 - page 71
71 USB DEVICE MANAGEMENT This function is not currently supported/activated. SER VICE MENU REMOTE CONTROL CODE Select the “Service” menu using the menu button , the buttons on the main menu and . Use the buttons to switch to “Remote Control Code” and to open press the button. The following display appears: Y ou can ...
-
Kathrein UFS 902 - page 72
72 OPERA TING FROM THE FRONT P ANEL If you have misplaced your remote control, or if the batteries are fl at, you can still operate your receiver from the front panel. BACKUP OPERA TION Because there are no number buttons, no password/PIN-protected functions can be displayed. There are four buttons on the front of the receiver . Stand-by button: Y ...
-
Kathrein UFS 902 - page 73
73 TECHNICAL APPENDIX FEA TURES Q Reception of digital satellite TV channels and radio programmes in DVB-S and DVB-S2 transmission standards Q Video decoding of MPEG-2 and MPEG-4/H.264 signals Q 12-character alphanumerical display shows channel names and transmitter information Q 4,000 channel memory positions Q Kathrein Convenience EPG with timer ...
-
Kathrein UFS 902 - page 74
74 T ype UFS 902si UFS 902sw Order no./colour 20210129/silver 20210130/black RF range Sat IF band MHz 950-2150 Input level band dBµV 44-83 Reception threshold (EB/NO) dB TV system video Modulation, FEC, demultiplexer DVB-S/DVB-S2 standard Video resolution CCIR 601 (720 x 576 lines), 576p, 720p, 1080i Video decoding MPEG-2-, MPEG-4-compatible Input ...
-
Kathrein UFS 902 - page 75
75 Signal Pin no. TV Audio right output 1 X Audio right input 2 Audio left output 3 X Audio earth 4 X Blue earth 5 X Audio left input 6 Blue signal 7 X Switching voltage 8 X Green earth 9 X Data signal 10 Green signal 1 1 X Data signal 12 Red earth 13 X Data earth 14 Red signal (C) 15 X Blanking signal 16 X Video earth 17 X Blanking signal earth 18 ...
-
Kathrein UFS 902 - page 76
76 CONNECTION EXAMPLE TECHNICAL APPENDIX UFS 902 Scart USB 2.0 5V... 500 mA max Dolby digital system Hi- fi system ...
-
Kathrein UFS 902 - page 77
77 TECHNICAL APPENDIX EXAMPLES single-cable systems Sat-ZF 950-2150 MHz UAS 484 T erres trische Antenne **) ESU 33 Single RTL Television 712 ESU 33 Single RTL Television 712 ESU 33 Single RTL Television 712 ESU 33 Single RTL Television 712 terr. H low/0kHz V 1-4 V high/22kHz H 1 = SCR(0) 1400 MHz 2 = SCR(1) 1516 MHz 3 = SCR(2) 1632 MHz 4 = SCR(3) 1 ...
-
Kathrein UFS 902 - page 78
78 TECHNICAL APPENDIX UAS 481 Single-cable feed system ERA 14 ERA 14 ...
-
Kathrein UFS 902 - page 79
79 EBC 10 Zum oder über EN 5 2 x Quatro-LNB UAS 484 EXU 908 Made in Germany 230V~ / 32W KLASSE CLASS 20510016 Receiver 1 ... 8 Receiver (No.): Frequency (MHz): SCR-Adress: 1 2 3 4 5 6 7 8 1284 1400 1516 1632 1748 1864 1980 2096 0 1 2 3 4 5 6 7 Error Power T err. Pos B V high V low H low H high 18V / 400mA Pos A H low V low V high H high 18V / 400m ...
-
Kathrein UFS 902 - page 80
80 SHORT TECHNICAL GLOSSAR Y AC3 Output for Dolby Digital signal ASTRA SES (Société Européene des Satellites) satellite system. Analogue and digital transponders in the frequency range 10.7-12.75 GHz. A V programme slot Preferred programme slot on TV set for external connections such as Scart and HDMI CAM – Conditional Access Module Decryption ...
-
Kathrein UFS 902 - page 81
81 SHORT TECHNICAL GLOSSAR Y Eb/No ratio The Eb/No ratio is a measure of the signal to noise ratio of a digital signal. The value is not identical to the C/N value familiar from analogue reception technology . At Eb/No values below 5 dB no reception is normally possible. EUTELSA T European Satellite operator , based in Paris. Many orbit positions a ...
-
Kathrein UFS 902 - page 82
82 NID The channel identi fi cation number is also referred to as the Network ID or NID. OSD – On-Screen Display Displays by the receiver on the TV screen (e.g. main menu) PA L Analogue TV standard Pay TV T elevision channels available on subscription (e.g. PREMIERE). Scrambled transmitters which can be decrypted only by using the appropriate sm ...
-
Kathrein UFS 902 - page 83
83 SHORT TECHNICAL GLOSSAR Y Smartcard Card from pay TV provider for decoding its programmes Stand-by Standby mode Symbol rate The symbol rate describes the quantity of data that is transmitted per second. The symbol rate is measured in MSymbols/s and is equal to the number of symbols received per second. Time-shift function T imeshifted playback T ...
-
Kathrein UFS 902 - page 84
84 ADDITIONAL INFORMA TION (i BUTTON) ................................................................................ 41 ALPHANUMERIC ENTRIES .................................................................................................... 31 ANTENNA CONFIGURA TION ................................................................................ ...
-
Kathrein UFS 902 - page 85
85 RECORD USER-DEFINED ...................................................................................................... 44 SERIES RECORDING ........................................................................................................... 45 REMINDER FUNCTION (CHANGE OVER T O PROGRAMME) ............................................... ...
-
Kathrein UFS 902 - page 86
86 TROUBLESHOOTING In the event of a malfunction, fi rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to wall socket 2. Antenna cables on receiver input 3. Receiver and TV set correctly connected by a Scart or cinch cable 4. Audio connections are made to Hi-Fi or Dolby Digital system as app ...
-
Kathrein UFS 902 - page 87
87 SER VICE If, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly , or if unexpected problems occur , please contact your specialist dealer . ...
-
Kathrein UFS 902 - page 88
Internet: http://www .kathrein.de KA THREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 P .O. Box 100 444 • 83004 Rosenheim • GERMANY 936.3352/B/1 108/ZWT - T echnical data subject to change. ...
Do you have a question concerning Kathrein UFS 902?
Use the form below
If you did not solve your problem by using a manual Kathrein UFS 902, ask a question using the form below. If a user had a similar problem with Kathrein UFS 902 it is likely that he will want to share the way to solve it.