English dropdown-ico

Manual Stanley Black & Decker SM50

18 pages 1.36 mb
Download

Go to site of 18

Summary
  • Stanley Black & Decker SM50 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 52724 2/2015 V er . 6 USER MANUAL Safety , Operation and Maintenance SM50 HYDRAULIC SUMP PUMP ...

  • Stanley Black & Decker SM50 - page 2

    2 ► SM50 User Manual DECLARA TION OF CONFORMITY DECLARATION OF CONF ORM ITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFO RMITA Hydraulic Tools _______ _________ ___________ ___________ _________ ___________ _________ ___ I, the undersigned: Ich, der Unterzeichnende: Je soussi gn? ...

  • Stanley Black & Decker SM50 - page 3

    SM50 User Manual ◄ 3 DECLARA TION OF CONFORMITY .......................................................................................................................... 2 SAFETY SYMBOLS .................................................................................................................................................. 4 SAFETY PREC ...

  • Stanley Black & Decker SM50 - page 4

    4 ► SM50 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker SM50 - page 5

    SM50 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs. ...

  • Stanley Black & Decker SM50 - page 6

    6 ► SM50 User Manual 52728 SM50 Combined Decal C AU TI O N SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA T ...

  • Stanley Black & Decker SM50 - page 7

    SM50 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker SM50 - page 8

    8 ► SM50 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS 4-6 1 ...

  • Stanley Black & Decker SM50 - page 9

    SM50 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max. uid tempe ...

  • Stanley Black & Decker SM50 - page 10

    10 ► SM50 User Manual PREOPERA TION PROCEDURES CHECK POWER SOURCE 1. Using a calibrated ow meter and pres sure gauge, make sure the hydraulic power source develops a ow of 7–12 gpm/26–45 Ipm at 1000–2000 psi/70– 140 bar . 2. Make certain that the power source is equipped with a relief valve set to open at 2100 psi/145 bar maxi- mum. ...

  • Stanley Black & Decker SM50 - page 11

    SM50 User Manual ◄ 1 1 CLEANING THE PUMPING CHAMBER Debris such as weeds, sand and other solids may be- come trapped in the water hose and pumping chamber . This can reduce pump performance. It is important that the pumping chamber be kept clean at all times. The chamber can be cleaned as follows: 1. Remove motor and impeller by removing the two ...

  • Stanley Black & Decker SM50 - page 12

    12 ► SM50 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hy- draulic system. • Always store the tool in a cl ...

  • Stanley Black & Decker SM50 - page 13

    SM50 User Manual ◄ 13 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation, always make sure the hydraulic power source is supplying the correct hydrau- lic ow and pressure as listed in the table. Use a owmeter know to be accurate. Check the ow wit ...

  • Stanley Black & Decker SM50 - page 14

    14 ► SM50 User Manual Capacity......................................................................................................................................... 500 gpm/1890 lpm Weight ..................................................................................................................................................... 21 lbs ...

  • Stanley Black & Decker SM50 - page 15

    SM50 User Manual ◄ 15 65132 MOTOR ASSEM- BL Y USED ON SUMP PUMPS WITH SERIAL NUMBERS 600 AND ABOVE, THIS MOTOR CAN ONL Y BE PUR- CHASED AS AN ASSEM- BL Y . INDIVIDUAL P ARTS ARE NOT A V AILABLE. SM50 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker SM50 - page 16

    16 ► SM50 User Manual ITEM NO. P ART NO. QTY DESCRIPTION 1 52669 1 VOLUTE 2 52720 1 CAMLOCK COUPLING 3 IN. 3 13815 1 HSHCS 5/16 – 18 × 3/4 4 56763 1 WASHER 5 00635 1 KEY 6 52671 1 IMPELLER 7 31032 1* SHIM .020 (* NOTE QTY WHEN DISASSEMBLING TOOL) 8 31033 1* SHIM .010 (* NOTE QTY WHEN DISASSEMBLING TOOL) 9 31034 1* SHIM .005 (* NOTE QTY WHEN DI ...

  • Stanley Black & Decker SM50 - page 17

    SM50 User Manual ◄ 17 For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation. With percussive tools, the nitrogen accumulator PSI must counte ...

  • Stanley Black & Decker SM50 - page 18

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Manufacturer Stanley Black & Decker Category Water Pump

Documents that we receive from a manufacturer of a Stanley Black & Decker SM50 can be divided into several groups. They are, among others:
- Stanley Black & Decker technical drawings
- SM50 manuals
- Stanley Black & Decker product data sheets
- information booklets
- or energy labels Stanley Black & Decker SM50
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stanley Black & Decker SM50.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stanley Black & Decker SM50, service manual, brief instructions and user manuals Stanley Black & Decker SM50. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stanley Black & Decker SM50.

Similar manuals

A complete manual for the device Stanley Black & Decker SM50, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stanley Black & Decker SM50 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stanley Black & Decker SM50.

A complete Stanley Black & Decker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stanley Black & Decker SM50 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stanley Black & Decker SM50, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stanley Black & Decker SM50, that we can find in the current document
3. Tips how to use the basic functions of the device Stanley Black & Decker SM50 - which should help us in our first steps of using Stanley Black & Decker SM50
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stanley Black & Decker SM50
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stanley Black & Decker SM50 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stanley Black & Decker SM50?

Use the form below

If you did not solve your problem by using a manual Stanley Black & Decker SM50, ask a question using the form below. If a user had a similar problem with Stanley Black & Decker SM50 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)