English dropdown-ico

Manual Stanley Black & Decker BR87

22 pages 1.7 mb
Download

Go to site of 22

Summary
  • Stanley Black & Decker BR87 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 65778 7/2014 V er . 1 1 USER MANUAL Safety , Operation and Maintenance BR87 HYDRAULIC BREAKER ...

  • Stanley Black & Decker BR87 - page 2

    2 ► BR87 User Manual DECLARA TION OF CONFORMITY DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ ___________ _________ ___________ _________ ___________ ___________ _ I, the undersigned: Ich, der Unterzeichnende: Je soussi gn? ...

  • Stanley Black & Decker BR87 - page 3

    BR87 User Manual ◄ 3 DECLARA TION OF CONFORMITY .......................................................................................................................... 2 SAFETY SYMBOLS .................................................................................................................................................. 4 SAFETY PREC ...

  • Stanley Black & Decker BR87 - page 4

    4 ► BR87 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker BR87 - page 5

    BR87 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs. ...

  • Stanley Black & Decker BR87 - page 6

    6 ► BR87 User Manual • Check fastener tightness often and before each use daily . • Never operate the tool if you cannot be sure that underground utilities are not present. • Do not wear loose tting clothing when operating the tool. • W arning: Hydraulic uid under pressure could cause skin injection injury . If you are injured by hy ...

  • Stanley Black & Decker BR87 - page 7

    BR87 User Manual ◄ 7 The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory . Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use. 28322 CE Decal 1 1207 Circuit T ype C Decal SAFETY T AG P/N 15875 (Shown smaller t ...

  • Stanley Black & Decker BR87 - page 8

    8 ► BR87 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker BR87 - page 9

    BR87 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS 4-6 1 ...

  • Stanley Black & Decker BR87 - page 10

    10 ► BR87 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max. uid temp ...

  • Stanley Black & Decker BR87 - page 11

    BR87 User Manual ◄ 1 1 NOTE: Partially depressing the trigger allows the tool to run at slow speed. Slow-speed operation permits easier starting of the tool bit into the work surface. 5. T o start, break an opening (hole) in the center of the surface. After making a hole, break portions of the material into the original opening. For best produc- ...

  • Stanley Black & Decker BR87 - page 12

    12 ► BR87 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hy- draulic system. • Always store the tool in a cl ...

  • Stanley Black & Decker BR87 - page 13

    BR87 User Manual ◄ 13 PROBLEM CAUSE REMEDY T ool does not run. Power unit not functioning. Check power unit for proper ow and pressure (7–9 gpm/26–34 lpm, 1500-2000 psi/105–140 bar . Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports. Be sure hoses are connected to their proper ports. Mechanic ...

  • Stanley Black & Decker BR87 - page 14

    14 ► BR87 User Manual ACCUMULA TOR TESTING PROCEDURE T o check or charge the accumulator the following equip - ment is required: 31254 Charge Kit: which includes the following. • Accumulator T ester (Part Number 02835) • Charging Assembly (P/N 15304) (P/N 15304 includes a liquid lled gauge with snub valve, hose and ttings.) • NITROGEN ...

  • Stanley Black & Decker BR87 - page 15

    BR87 User Manual ◄ 15 UNDERW A TER MODEL PREVENT A TIVE MAINTENANCE After each use, the movable portions of the tool that were exposed to water should be ushed with a water displacing oil such as WD40™. Remove any remaining water and debris as follows: 1. Turn the tool upside down (without the tool bit) and spray oil through the drive hex an ...

  • Stanley Black & Decker BR87 - page 16

    16 ► BR87 User Manual Pressure Range.............................................................................................................. 1500–2000 psi/105–140 bar Flow Range ............................................................................................................................... 7–9 gpm / 26–34 lpm Nominal ...

  • Stanley Black & Decker BR87 - page 17

    BR87 User Manual ◄ 17 ACCESSORIES 1-1/8 IN. HEX × 6 IN. SHANK Moil Point, 14 in. Long UC ................................................................................................................................. 02333 Chisel Point, 14 in. Long UC ............................................................................................. ...

  • Stanley Black & Decker BR87 - page 18

    18 ► BR87 User Manual BR87 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker BR87 - page 19

    BR87 User Manual ◄ 19 BR87 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker BR87 - page 20

    20 ► BR87 User Manual Item No. Part No. Qty Description 1 06185 1 HANDLE ASSY (INCL ITEM 35) 1 1435 1 BREAKER HANDLE (TRIGGER LOCK MODELS ONL Y) 2 04050 1 V AL VE CAP ASSY 3 04051 1 CHARGING V AL VE 4 04052 1 O-RING 5 04053 1 1434 1 TRIGGER TRIGGER (TRIGGER LOCK MODELS ONL Y) 6 00844 1 SPIROL PIN 7 04054 3 O-RING 8 22891 2 SPIROL PIN, 3/16 × 1-5 ...

  • Stanley Black & Decker BR87 - page 21

    BR87 User Manual ◄ 21 For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation. With percussive tools, the nitrogen accumulator PSI must counte ...

  • Stanley Black & Decker BR87 - page 22

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Manufacturer Stanley Black & Decker Category Power Hammer

Documents that we receive from a manufacturer of a Stanley Black & Decker BR87 can be divided into several groups. They are, among others:
- Stanley Black & Decker technical drawings
- BR87 manuals
- Stanley Black & Decker product data sheets
- information booklets
- or energy labels Stanley Black & Decker BR87
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stanley Black & Decker BR87.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stanley Black & Decker BR87, service manual, brief instructions and user manuals Stanley Black & Decker BR87. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stanley Black & Decker BR87.

Similar manuals

A complete manual for the device Stanley Black & Decker BR87, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stanley Black & Decker BR87 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stanley Black & Decker BR87.

A complete Stanley Black & Decker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stanley Black & Decker BR87 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stanley Black & Decker BR87, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stanley Black & Decker BR87, that we can find in the current document
3. Tips how to use the basic functions of the device Stanley Black & Decker BR87 - which should help us in our first steps of using Stanley Black & Decker BR87
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stanley Black & Decker BR87
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stanley Black & Decker BR87 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stanley Black & Decker BR87?

Use the form below

If you did not solve your problem by using a manual Stanley Black & Decker BR87, ask a question using the form below. If a user had a similar problem with Stanley Black & Decker BR87 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)