English dropdown-ico

Manual National Instruments 9211

19 pages 0.39 mb
Download

Go to site of 19

Summary
  • National Instruments 9211 - page 1

    USER GUIDE AND SPECIFICA TIONS USB-9211/9211A 4-Channel, 24-Bit Thermocouple Input Devices This user guide describes how to use the National Instruments USB-9211/9211A devices and lists the specifications. Introduction The NI USB-9211/9211A data acquisition d evice pro vides a USB interface for four channels of 24-bit thermoco uple inputs with inte ...

  • National Instruments 9211 - page 2

    USB-9211/9211A User Guid e and Specifications 2 ni.com Dimensions Figure 2 shows the USB-9211/9211A devi ce dimensions. Figure 2. USB-9211/9211A Series Devices in Inches (Millimeters) Safety Guidelines Operate the USB-9211/9211A only as described in these operating instructions. Note Although the NI 9211 module may have more stringent certification ...

  • National Instruments 9211 - page 3

    © National Instruments Cor poration 3 USB-9211/9211A User Guide and Specifications Safety Guidelines for Hazardous Vo ltages If hazardous voltages are connected to the module, take the following precautions. A hazardous vo ltage is a voltage greater than 42.4 V pk or 60 VDC to earth ground. Caution Ensure that hazardous v oltage wiring is performe ...

  • National Instruments 9211 - page 4

    USB-9211/9211A User Guid e and Specifications 4 ni.com Related Documentation If your device uses NI-D A Qmx Base, refer to ni.com to do wnload the software. Installing the USB-9211/9211A Device Installing the Software Before installing the device, you must install the software you plan to use with the device. Refer to the Software section of this m ...

  • National Instruments 9211 - page 5

    © National Instruments Cor poration 5 USB-9211/9211A User Guide and Specifications 3. Align the I/O module with the carrier, as sho wn in Figure 3. Figure 3. Module Installation 4. Squeeze the latches and insert the NI 9211 module into the carrier . 5. Press firmly on the connector side of the NI 9211 module until the latches lock the module into ...

  • National Instruments 9211 - page 6

    USB-9211/9211A User Guid e and Specifications 6 ni.com Mounting the USB-9211 /9211A to a Panel Threaded inserts are located in the USB-921 1/9211A for mounting it to a panel. Refer to Figure 5 for dimensions. Figure 5. Module Dimensions Connecting the USB-9211/ 9211A to a Computer Plug one end of the USB cable into th e USB-9211/9211A and the other ...

  • National Instruments 9211 - page 7

    © National Instruments Cor poration 7 USB-9211/9211A User Guide and Specifications Wiring the USB-9211/9211A The USB-9211/9211 A has a 10-terminal, detachabl e high voltage screw terminal enclosure that provides connections for four therm ocouple input channels. Each channel has a terminal to whi ch you can connect the positive lead of the thermoc ...

  • National Instruments 9211 - page 8

    USB-9211/9211A User Guid e and Specifications 8 ni.com Refer to T able 3 for the termin al assignments for each channel. Assembling the High V oltage Screw T erminal Backshell The high voltage screw terminal back shell must be instal led when using hazardous voltages (>42.4 V pk , 60 VDC). Refer to Figure 7 while completing the following steps: ...

  • National Instruments 9211 - page 9

    © National Instruments Cor poration 9 USB-9211/9211A User Guide and Specifications Figure 7. High V oltage Screw T erminal Backsh ell USB-9211/9211A Circuitr y The USB-9211/9211A channels share a common gro und that is isolated from the chassis and the host comput er. Each channel has an impedance between the TC + and COM terminals and between the ...

  • National Instruments 9211 - page 10

    USB-9211/9211A User Guide and Specifications 10 ni.com Figure 8. Input Cir cuitry for One Channel If thermocouples are connected to the USB-921 1/9211A, the gain and of fset errors resulting from the so ur ce impedance of the thermocouples are negligible for most applications. Othe r voltage sources with a higher source impedance can introduce mo r ...

  • National Instruments 9211 - page 11

    © National Instruments Corporation 11 USB- 9211/9211A User Gu ide and Specifications Measurement Accuracy fo r the Different T ypes of Thermocouples Figures 9, 10, 11, 12, and 13 show the typical and maximum errors for the different thermocouple types when used with the USB-9211/9211A over the full temperature range. The figure s also s how the ma ...

  • National Instruments 9211 - page 12

    USB-9211/9211A User Guide and Specifications 12 ni.com Figure 10. T ype E and T Errors Figure 11. T ype J and N Errors –200 0 200 400 600 800 1000 0 2 3 4 Max ov er T emp Range with A utozero Max at Room T emp Range without A utozero T yp ov er T emp Range with Autozero Error ( ° C) Measured T emperature ( ° C) 1 –200 0 200 400 600 800 1000 1 ...

  • National Instruments 9211 - page 13

    © National Instruments Corporation 13 USB- 9211/9211A User Gu ide and Specifications Figur e 12. T ype K Errors Figure 13. T ype R and S Errors Cold-Junction T emperatur e Measurement Accuracy Heat from other nearby h eat sources can cause errors in thermocouple measurements by heating up the term inal s so that they are at a different temperature ...

  • National Instruments 9211 - page 14

    USB-9211/9211A User Guide and Specifications 14 ni.com Minimizing Thermal Gradients Thermocouple wire can be a significan t source of thermal gradients if it conducts heat or cold directly to terminal j unctions. To min imize these errors, follow these guidelines: • Use small-gauge thermocouple wire. Smaller wire transfers less heat to or from th ...

  • National Instruments 9211 - page 15

    © National Instruments Corporation 15 USB- 9211/9211A User Gu ide and Specifications Cold-junction compensation sensor accuracy 0 to 60 °C ...................... .................. 0.6 °C (1.1 °F) typ, 1.3 °C (2.3 °F) max Conversion time ...................... ... ............ 70 ms per channel; 420 ms total for all ch annels including the au ...

  • National Instruments 9211 - page 16

    USB-9211/9211A User Guide and Specifications 16 ni.com Offset error from source impedance ...... . 0.05 µ Vt y p ,0 . 0 7 µ Vm a x p e r Ω source impedance due to input current Power Requirements Current consumption from USB .............500 mA, max Suspend mode ................ ................. .2.5 mA, max Bus Interface USB specification USB ...

  • National Instruments 9211 - page 17

    © National Instruments Corporation 17 USB- 9211/9211A User Gu ide and Specifications V oltages Connect only voltages that are within these limits. Channel-to-COM .................... ............... ± 30 V max, Measurement Category I Measurement Category I is for meas urements performed on circuits not directly connected to the electrical di stri ...

  • National Instruments 9211 - page 18

    USB-9211/9211A User Guide and Specifications 18 ni.com Maximum altitude ................. ..................2,000 m (at 25 °C ambient temperature) Pollution Degree (IEC 60664) .... ............2 Electromagnetic Compatibility Emissions ...................... ................. .........EN 55011 Class A at 10 m FCC Part 15A above 1 GHz Immunity ..... ...

  • National Instruments 9211 - page 19

    National Instruments, NI, ni.com, and LabVIEW are tradem arks of National Instruments Corporation. Refer to t he Terms of Use section on ni.com/legal for m ore inform ation about Natio nal Instruments trademarks. Other product and compan y names mentioned herein are t rademarks or trade names of their respective companie s. For patents coveri ng Na ...

Manufacturer National Instruments Category Computer Drive

Documents that we receive from a manufacturer of a National Instruments 9211 can be divided into several groups. They are, among others:
- National Instruments technical drawings
- 9211 manuals
- National Instruments product data sheets
- information booklets
- or energy labels National Instruments 9211
All of them are important, but the most important information from the point of view of use of the device are in the user manual National Instruments 9211.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals National Instruments 9211, service manual, brief instructions and user manuals National Instruments 9211. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product National Instruments 9211.

Similar manuals

A complete manual for the device National Instruments 9211, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use National Instruments 9211 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of National Instruments 9211.

A complete National Instruments manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual National Instruments 9211 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the National Instruments 9211, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the National Instruments 9211, that we can find in the current document
3. Tips how to use the basic functions of the device National Instruments 9211 - which should help us in our first steps of using National Instruments 9211
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with National Instruments 9211
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of National Instruments 9211 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning National Instruments 9211?

Use the form below

If you did not solve your problem by using a manual National Instruments 9211, ask a question using the form below. If a user had a similar problem with National Instruments 9211 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)