English dropdown-ico

Manual O'Neil For 8100

24 pages 0.91 mb
Download

Go to site of 24

Summary
  • O'Neil For 8100 - page 1

    User's Guide MICROFLASH 8I ...

  • O'Neil For 8100 - page 2

    ...

  • O'Neil For 8100 - page 3

    TABLE OF CONTENTS 3 microFlash 8 i Printer 4 Open View 4 Closed View 4 Installing a Radio Card 5 Using the Ribbon 6 Installing the Ribbon 6 Removing the Ribbon 7 Installing and/or Replacing Batteries 8 Charging the Battery 9 Loading Paper 10 Paper Quantity Guidelines 12 Tearing the Paper 12 Printing a Self-Test 12 Setting Top of Form (TOF) 13 Using ...

  • O'Neil For 8100 - page 4

    MICROFLASH 8I PRINTER USER'S GUIDE 4 microFlash 8i Printer Open View Closed View Battery cavit y Battery cable Access cover Locking lever (green knob) Control panel Printer assembly Figure 1 Pap e r Ex i t Handle Contr ol panel Figure 2 ...

  • O'Neil For 8100 - page 5

    MICROFLA SH 8I PRINTER USER'S GUIDE 5 Installing a Radio Card 1. Open the printer’s co ver . 2. Push in the locking tab and lift the access cover (Figures 3 and 4). 3. Insert the radio card f ace up into the PCMCIA slot (Figure 5). 4. Close the access cover and press down until the locking tab clicks into place. Note: The f ollowing informat ...

  • O'Neil For 8100 - page 6

    MICROFLASH 8I PRINTER USER'S GUIDE 6 Using the Ribbon Installing the Ribbon The printer ships without a ri bbon installed. T o install a ribbon, perform the f ollowing: 1. Remo ve the ribbon from its packaging. 2. Open the printer’s co ver . 3. Remove the or ange “Open Printer” label from the locking lever (green knob). 4. Depress the lo ...

  • O'Neil For 8100 - page 7

    MICROFLA SH 8I PRINTER USER'S GUIDE 7 Removing the Ribbon 1. Slide the printhead awa y from the edge of t he printer (Figure 9). 2. Pull the ribbon away fr om the printer (Figure 10). Figure 9 Figure 10 ...

  • O'Neil For 8100 - page 8

    MICROFLASH 8I PRINTER USER'S GUIDE 8 Installing and/or Replacing Batteries 1. Open the printer ’ s cover . V erify the control panel is faci ng to wa rd y ou . 2. Place the battery in the batte ry cavity (Figure 11) . 3. Connect the printer's cable connector to the bat tery (Figures 12a and 12b). V erif y the printer's battery conn ...

  • O'Neil For 8100 - page 9

    MICROFLA SH 8I PRINTER USER'S GUIDE 9 4. Install the battery strap o ver the printer's cable connector and the battery so that they are both h eld in place (Figure 13). 5. Close the printer’s co ver . 6. Charge the battery . F or more information, see Charging the Ba ttery on page 9 . Charging the Battery Y ou can charge the bat tery ei ...

  • O'Neil For 8100 - page 10

    MICROFLASH 8I PRINTER USER'S GUIDE 10 Loading Paper 1. Open the two latches on the side of the printer’ s cover and lift the printer’ s cove r to the fully open position. 2. Depress the locking lever (green knob) to open the print mechanism (Figure 14). 3. V erify the center guide is centered (Figur e 15) 4. Lift the two tractor f eed clip ...

  • O'Neil For 8100 - page 11

    MICROFLA SH 8I PRINTER USER'S GUIDE 11 5. Fold the stack of paper in half with the short sides together and with the top of the form c oming out from the inside fold (Figure 17). 6. Place the paper into the paper cavity with the bottom edges under the paper lip in the bottom of the cavit y (Figure 18). 7 . F eed the top of the form from the in ...

  • O'Neil For 8100 - page 12

    MICROFLASH 8I PRINTER USER'S GUIDE 12 Paper Quantity Guidelines Tearing the Paper 1. Set th e paper to to p of fo rm. F or more information, see Setting T op of F orm (TOF) on page 13 . 2. Grab one side of the paper at a leading edge and pull up. Once the paper has started tearing at the perfor ation, finish with a swift pull upward and away ( ...

  • O'Neil For 8100 - page 13

    MICROFLA SH 8I PRINTER USER'S GUIDE 13 Setting Top of Form (TOF) 1. Press button 1 to turn on the printer . 2. Position the paper by pr essing button 1 until the end of the paper is at the edge of the ca se. If necessary , press button 2 to back feed the paper . 3. T urn the printer off by pressing buttons 1 and 2 simultaneously (Figure 22). 4 ...

  • O'Neil For 8100 - page 14

    MICROFLASH 8I PRINTER USER'S GUIDE 14 Using Buttons and Indicators Control Panel LED Indicators Charge LED LED Description Ac tion Solid red Charging in progr ess. None. Red f la s h - slow Battery disconnected. Low temperatur e. Connect battery . Change environment. Red flas h - fast High temperatu re. Change envir onment. Red to or ange - sl ...

  • O'Neil For 8100 - page 15

    MICROFLA SH 8I PRINTER USER'S GUIDE 15 Pow e r L E D Button Functions Charge LED LED Description Action Green P ower on. None. Green flash - fast Pap e r o ut , h e a d j a m . Install pa per , check for paper jam. Green to or ange alternating flash - fast If a rad io card is installed, indicates radio and printer are on. None. Orange flash - ...

  • O'Neil For 8100 - page 16

    Audio Indicators LED Description Action Long series of short beeps Head jam. Check for paper jam. 1 short RF power is on (when RF power button is pressed and RF power was off ). None. 1 long Boot code is starting or restarting (occurs more than once when downloading new firmware). None. 2 short RF power is off (when RF power button is pressed and w ...

  • O'Neil For 8100 - page 17

    MICROFLA SH 8I PRINTER USER'S GUIDE 17 Using Power Options Use the following options to power the printer: • AC AC/DC Power Supply • DC Cigarette Adapter • Batteries NiMH The red-tagged cable attached to the printer connects to the AC adapter cable. The white-tagged cable connects to the cigarett e lighter adapter for use in vehicles. If ...

  • O'Neil For 8100 - page 18

    MICROFLASH 8I PRINTER USER'S GUIDE 18 Attaching Cables The RJ11 (telephone style) connector at tached to the printer connects to your notebook and/or computer or handheld (HHC) using an optional data cable or handheld cradle. Configuring the Printer The printer has many configurable set tings. T o configure or upgrade firmw are, download the W ...

  • O'Neil For 8100 - page 19

    19 MICROFLA SH 8I PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Clas s B digital device , pursuant to Pa rt 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf ul interference in a residential installation. This equipment gener ...

  • O'Neil For 8100 - page 20

    20 MICROFLASH 8I PRINTER USER'S GUIDE Warranty The Company warr ants that O'Neil Pro duct Deve lopment, Inc.'s products are free from defects in manufacturi ng materials and workmanship for one (1) year f rom date of original purchase to Buyer/Distributor (OEMs 90 days from the da te of purchase). Batteries, ca bles, power supplies, ...

  • O'Neil For 8100 - page 21

    21 MICROFLA SH 8I PRINTER USER'S GUIDE ...

  • O'Neil For 8100 - page 22

    ...

  • O'Neil For 8100 - page 23

    ...

  • O'Neil For 8100 - page 24

    W orld Headquarters O'Neil Product Development 8 Mason Irvine, CA 92618-2705 Ph: 949.458.0500 Fx: 949.458.0708 Europe 6 Joplin Court, Crownhill Milton Keynes MK8 0JP United Kingdom Ph: +44 (0) 1908 635360 Fx: +44 (0) 1908 635361 AustralAsia 1/8 Railway T errace Dutton Park QLD 4102 Austalia Ph: +61 (7) 3255 3360 Fx: +61 (7) 3255 3365 WWW .ONEI ...

Manufacturer O'Neil Category Printer

Documents that we receive from a manufacturer of a O'Neil For 8100 can be divided into several groups. They are, among others:
- O'Neil technical drawings
- For 8100 manuals
- O'Neil product data sheets
- information booklets
- or energy labels O'Neil For 8100
All of them are important, but the most important information from the point of view of use of the device are in the user manual O'Neil For 8100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals O'Neil For 8100, service manual, brief instructions and user manuals O'Neil For 8100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product O'Neil For 8100.

Similar manuals

A complete manual for the device O'Neil For 8100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use O'Neil For 8100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of O'Neil For 8100.

A complete O'Neil manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual O'Neil For 8100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the O'Neil For 8100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the O'Neil For 8100, that we can find in the current document
3. Tips how to use the basic functions of the device O'Neil For 8100 - which should help us in our first steps of using O'Neil For 8100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with O'Neil For 8100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of O'Neil For 8100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning O'Neil For 8100?

Use the form below

If you did not solve your problem by using a manual O'Neil For 8100, ask a question using the form below. If a user had a similar problem with O'Neil For 8100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)