English dropdown-ico

Manual SMC Networks SMC7004ABR

112 pages 1.59 mb
Download

Go to site of 112

Summary
  • SMC Networks SMC7004ABR - page 1

    Barricade ™ Broadband Router 10/100 Mbps Br oadband Router ◆ Internet access via – • 10/100 Mbps W AN port connection to xDSL/Cable modem, or • RS-232 console port connection to ISDN/PSTN modem ◆ Home networking via – • Four/Eight 10/100 Mbps Ethernet switch ports ◆ Built-in Print Server ◆ Automatic IP conf iguration with DHCP ? ...

  • SMC Networks SMC7004ABR - page 2

    ...

  • SMC Networks SMC7004ABR - page 3

    38 T e s l a Irvine, CA 92618 Phone: (949) 679 -8000 Barricade ™ Br oadband Router User Guide From SMC ’ s Barricade line of Broadband Routers February 2002 Revision Numb er: R02 ...

  • SMC Networks SMC7004ABR - page 4

    Copyright Information fu rnished by SMC Networks, Inc. (SMC) is believed to be accur ate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may r esult from its use. No licen se is granted by impl ication or otherwise unde r any patent or patent rights ...

  • SMC Networks SMC7004ABR - page 5

    v L IMITED W ARRANTY Limited Warranty S tatement: SMC Networks, Inc. (“ SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC prod ucts carry a standard 90-day limited warranty from the date of purchase fro m SMC or its Authorized Reseller. SMC m ...

  • SMC Networks SMC7004ABR - page 6

    L IMIT ED W ARRANTY vi WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPE RATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUC T IN QUESTION, AT SMC’S OPTI ON. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARR ANTIES OR CONDITIONS , EXPRESS OR IMPLIED, EITHER IN FACT ...

  • SMC Networks SMC7004ABR - page 7

    vii C OMPLIANCES FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequ ency e ...

  • SMC Networks SMC7004ABR - page 8

    C OMPLIANCES viii Industry Canada - Class B This digital apparatus does not exceed t he Class B limits for radio noise emissions from digital apparatus as set out in the interference- causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications. Cet appareil numérique respecte les limites de bru its rad ...

  • SMC Networks SMC7004ABR - page 9

    C OMPLI ANCES ix Safety Compliance Underwriters Laboratories Compliance Statement Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following : The unit automatically matches the connected input volt age. Therefore, no additional adjustments are necessary when connectin ...

  • SMC Networks SMC7004ABR - page 10

    C OMPLIANCES x 11. Wird das Gerät über einen längeren Zeitraum nicht benutz t, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeit en in das Gerät gelangen. Dies könnte einen Brand bzw. elekt rischen Schlag a ...

  • SMC Networks SMC7004ABR - page 11

    T ABLE OF C ONTENTS xi T ABLE OF C ONTENTS 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 About the Barricade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Applications . . . . . . . . . . . . ...

  • SMC Networks SMC7004ABR - page 12

    T ABLE OF C ONTENTS xii Static IP Address – Fixed IP . . . . . . . . . . . . . . . . . . . . . 4-10 PPP over Ethernet – PPPoE . . . . . . . . . . . . . . . . . . . . 4-11 Dial-up on Demand – Modem . . . . . . . . . . . . . . . . . . . 4-12 DNS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -13 Configuring Client S ...

  • SMC Networks SMC7004ABR - page 13

    T ABLE OF C ONTENTS xiii 6 Configuring Printer Services . . . . . . . . . . . . . . . . . 6-1 Install the Printer Port Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Configure the Print Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Configure the Network Printer in Windows 95/98/ME/ 2000 . . . . . . . . . ...

  • SMC Networks SMC7004ABR - page 14

    T ABLE OF C ONTENTS xiv ...

  • SMC Networks SMC7004ABR - page 15

    1-1 C HAPTER 1 I NTRODUCTION Congratulations on your purchase of the Barricad e ™ Broadband Router. SMC is proud to provi de you with a powerful yet simp le communication device for connecting your local area network (LAN) to the Inte rnet. For those who want to surf on the Int ernet at the lowest possible cost, this Broadband Router provides a c ...

  • SMC Networks SMC7004ABR - page 16

    F EATURES AND B ENEFITS 1-2 Features and Benefits • Internet connection to xDSL or Cable modem via a 10/100 Mbps WAN por t • Internet connection to ISDN TA or PSTN modem via an RS-232 console port • Local network connection via 10/100 Mbps Ethernet ports • Built-in Print Server for any client attached to the LAN • DHCP for dynamic IP conf ...

  • SMC Networks SMC7004ABR - page 17

    I NTRODUCTION 1-3 Applications Many advanc ed applications are pr ovided by the B arricade, such as: • LAN Access The Barricade provides connectivity to 10/100 Mbps devices, making it easy to create a network in small offices or homes. • Internet Access This device supports Internet access through an xDSL, Cable, ISDN or PSTN connection. Since ...

  • SMC Networks SMC7004ABR - page 18

    A PPLICATIONS 1-4 • User-Definable Application Sensing Tunnel You can define special applications that require multiple connections such as Internet gaming, videoconferencing, and Internet telephony. The Barricade can then sense the application type and open a multi-port tun nel for it. • DMZ Host Support Allows a networked computer to be fully ...

  • SMC Networks SMC7004ABR - page 19

    I NTRODUCTION 1-5 • Point-to-Point Tunneling Protocol – Provides a secure tunnel for remote client access to a PPTP security gateway. PPTP includes provisions for call ori gination and flow control required by ISPs. • Layer Two Tunneling Protocol – Includes most of the features provided by PPTP, but has less overhead and is more suited for ...

  • SMC Networks SMC7004ABR - page 20

    A PPLICATIONS 1-6 ...

  • SMC Networks SMC7004ABR - page 21

    2-1 C HAPTER 2 I NSTALLATION Before installing the Barricade ™ Broadband Router, verify that you have all the items listed under “Package Contents.” If any of the items are missing or damaged, contact your local SMC distributor. Also be sure that you have all the necessary cabling before installing the Barricade. After installing the Barricad ...

  • SMC Networks SMC7004ABR - page 22

    I NSTALLAT ION 2-2 Please fill out and return the Warranty Registration Card to SMC or register on SMC’s Web site at www.smc.com. The Barricade Broadband Router is covered by a limited lifetime warranty. Description of Hardware The Barricade Broadband Router can be connected to the Internet or to a remote site using its RJ-45 WAN port or RS-232 s ...

  • SMC Networks SMC7004ABR - page 23

    I NSTALLAT ION 2-3 • 4 RJ-45 ports for connection to a 10BASE-T/100BASE-TX Ethernet Local Area Network (LAN). These ports can auto- negotiate the operating speed to 10/100 Mbps, the mode to half/ full duplex, and the pin signals to MDI/ MDI-X (i.e., allowing these ports to be connected to any network device with straight-through cable). These por ...

  • SMC Networks SMC7004ABR - page 24

    I NSTALLAT ION 2-4 The following figure shows the components of the Barricade: SMC7004ABR Figure 2-1. Front and Rear Panels Item Description Reset Button Use this button to reset the power and restore the default factory settings. LEDs Power, WAN and LAN port status indicators. (See Veri fy Port Status on pag e 2-10.) LAN Ports Fast Ethernet ports ...

  • SMC Networks SMC7004ABR - page 25

    I NSTALLAT ION 2-5 System Requirements You must have an ISP that meets the following min imum requirements: • Internet access from your local telephone company or Internet Service Provider (ISP) using an xDSL modem, Cable modem, ISDN TA, or PSTN analog modem. You may also have access over the telephone system to an analog modem at another site. ? ...

  • SMC Networks SMC7004ABR - page 26

    I NSTALLAT ION 2-6 You should also remember to turn off the power, remove the power cord from the outlet, and keep your hands dry when you install the Barricade. Basic Installation Procedure 1. Connect the LAN : You can connect the Barricade to your PC, or to a hub or switch. Run Ethernet cable from one of the LAN ports on the front of the Barricad ...

  • SMC Networks SMC7004ABR - page 27

    I NSTALLAT ION 2-7 Attach to Your Network Using Ethernet Cabling The 4 LAN ports on the Barricade can auto-negotiate the connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, as well as the transmission mode to half-du plex or full-duplex. Th e LAN ports on SMC7004ABR support auto-configuration for pin signals (auto-MDI/ MDI-X) that allow ...

  • SMC Networks SMC7004ABR - page 28

    I NSTALLAT ION 2-8 2. Make sure each twisted-pair cable does not exceed 100 meters (328 feet). Figure 2-3. Making LAN Connection s Attach the Barricade to the Internet If Internet services are provided through an xDSL or Cable modem, use unshielded or shielded twisted-pair Ethernet cable (Category 3 or greater) with RJ-45 plugs to connect the broad ...

  • SMC Networks SMC7004ABR - page 29

    I NSTALLAT ION 2-9 Note: When connecting to the WAN port, use 100-ohm Category 3, 4 or 5 shielded or un shielded twisted-pair cable w ith RJ-45 connectors at both ends for all connections. Connect a Printer If you connect a printer to the Barricade, all the computer users connected to your LAN can have access to this printer. Connect a standard par ...

  • SMC Networks SMC7004ABR - page 30

    I NSTALLAT ION 2-10 Verify Port Status Check the power and port indicators as shown in the followi ng table . LED Condition Status Power (Green) On Barricade is receiving power. WAN (Green) On The WAN port has establ ished a valid network connection. Flashing The WAN port is tra nsmitting or receiving traffic. Link/Act (Green) On The indicated LAN ...

  • SMC Networks SMC7004ABR - page 31

    3-1 C HAPTER 3 C ONFIGURING C LIENT PC S TCP/IP Configuration To access the Internet through the Barricade ™ Broadband Router, you must configure the network settings of the computers on your LAN to use the same IP subnet as the Barricade. The default network settings for the Barricade are: IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 Note: ...

  • SMC Networks SMC7004ABR - page 32

    P RINTER C LIENT I NSTALLATION 3-2 Printer Client Installation If you need to provide print services for devices attached to the Barricade, then install the Port Monitor program from the Barricade CD (for Windows 95/98/ME/NT/2000), and configure the Barricade’s print server on each network station. The Barricade printer server supports Windows 95 ...

  • SMC Networks SMC7004ABR - page 33

    4-1 C HAPTER 4 C ONFIGURING THE B ARRICADE After you have configured TCP/IP on a client computer, you can use a Web browser to configure the Barricade ™ Broadband Router. The Barricade can be configured by any Java-supported browser including Internet Explorer 4.0 or above, or Netscape Navigator 4.0 or above. Using the Web management interface, y ...

  • SMC Networks SMC7004ABR - page 34

    N AVIGATING THE W EB B ROWSER I NTERFACE 4-2 Navigating the Web Browser Interface The Barricade’s management interface includes four key menus – Status, Help, Tools, and Setup. The Status and Help menus provide general information on the current settings and how to configure the Barricade. The Setup menu is used to configure the LAN and WAN int ...

  • SMC Networks SMC7004ABR - page 35

    C ONFIGURING THE B ARRICADE 4-3 Making Configuration Changes Configurable parameters have a dialog box or a drop-down list. Once a configuration change has been made on a page, be sure to click the “Enter” button at the bottom of the page to confirm the new setting. Note: To ensure proper screen refresh after a command entry, be sure that Inter ...

  • SMC Networks SMC7004ABR - page 36

    M AIN M ENU 4-4 Main Menu Using the Web management interface, you can define system parameters, manage and control the Barricade and its ports, or monitor network condition s. The following table brief ly describes the selections available from this program. Menu Description Setup Menu Configures TCP/IP settings and client services. Change Password ...

  • SMC Networks SMC7004ABR - page 37

    C ONFIGURING THE B ARRICADE 4-5 DHCP Client Log Displays information on all DHCP clients attached to your network. Tools Menu Contains options to reset the system, res tore configuration set tings, or update system firmware. Reset Barricade Reboots the system and retai ns all of your configuration settings. Restore Factory Settings Restores all con ...

  • SMC Networks SMC7004ABR - page 38

    N ETWORKING AND C LIENT S ERVICES 4-6 Networking and Client Services Use the Setup menu to configure the LAN interface (including TCP/IP parameters for the Barricade’s gateway address, DHCP address pool for dynamic client address allocation), the WAN connection options, DNS domain name mapping, and other advanced services. You can use the Setup W ...

  • SMC Networks SMC7004ABR - page 39

    C ONFIGURING THE B ARRICADE 4-7 Change Password Use this menu to restrict management access based on a specific password. Anyone can access the Status and Help menus, but you must enter a password to access the configuration options provided by the Setup and Tool s menus. By default, there is no password, so please assign a password to the Barricad ...

  • SMC Networks SMC7004ABR - page 40

    N ETWORKING AND C LIENT S ERVICES 4-8 Set Time Zone Set the time zone for the Barricade. This information is used for log entries and client filtering. LAN Gateway and DHCP Settings Configure the gateway address of the Barricade. To dynamically assign the IP address for client PCs, enable the DHCP Server, set the lease time, and then specify the ad ...

  • SMC Networks SMC7004ABR - page 41

    C ONFIGURING THE B ARRICADE 4-9 the Barricade in the client address pool. WAN Configuration Specify the WAN connection type required by your Internet Service Provider, then click “More Configuration” to provide detailed configuration parameters for the selected connection type. Specify one of the first three options to configure a WAN connectio ...

  • SMC Networks SMC7004ABR - page 42

    N ETWORKING AND C LIENT S ERVICES 4-10 Dynamic IP Address – DHCP The Host Name is optional, but may be r equired by some ISPs. The default MAC address is set to the WAN’s physical interface on the Barricade. Use this address when registering for Internet service, and do not change it unless required by your ISP. You can use the “Clone MAC Add ...

  • SMC Networks SMC7004ABR - page 43

    C ONFIGURING THE B ARRICADE 4-11 Note: You may need a fixed address if you want to provide Internet services, such as a Web server or FTP server. PPP over Ethernet – PPPoE Enter the PPPoE user name and password assigned by your ISP. The Service Name is normally optional, but may be required by some providers. ...

  • SMC Networks SMC7004ABR - page 44

    N ETWORKING AND C LIENT S ERVICES 4-12 Dial-up on Demand – Modem If you are accessing the Internet via an ISDN TA or PSTN modem attached to the serial port on the Barricade, then you must specify your account information on this screen as described below. Check if you only use a dial-up modem to connect to the Internet. – If the serial port is ...

  • SMC Networks SMC7004ABR - page 45

    C ONFIGURING THE B ARRICADE 4-13 Modem Initialization string – Enter the initialization string provided by your modem manufacturer. The following is a sample initialization string: “ATQ1S0=1&D0&K0&W” as defined below: Q1 : Inhibit result codes to DTE S0=1 : Auto answer on first ring D0 : Don’t care DTR K0 : Disables DTE/DCE flo ...

  • SMC Networks SMC7004ABR - page 46

    N ETWORKING AND C LIENT S ERVICES 4-14 Configuring Client Services The Barricade includes a broad range of client services, including firewall protection, network address translation, virtual server, connection support for special applications, and restricted Internet access for specified clients. You can configure these functions using the Setup W ...

  • SMC Networks SMC7004ABR - page 47

    C ONFIGURING THE B ARRICADE 4-15 Virtual Server If you configure the Barricade as a virtual server, remote users accessing services such as Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses. In other words, depending on the requested service (TCP/UDP port numb ...

  • SMC Networks SMC7004ABR - page 48

    N ETWORKING AND C LIENT S ERVICES 4-16 HTTP request from outside users will be transferred to 192.168.2.2. Therefore, by just entering the IP Address provided by the ISP, Internet users can access the service they need at the local address to which you redirect them. Some of the more common TCP service ports include: HTTP: 80, FTP: 21, Telnet: 23 a ...

  • SMC Networks SMC7004ABR - page 49

    C ONFIGURING THE B ARRICADE 4-17 Specify the port normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or UDP, then enter the public ports associated with the trigger port to open them for inbound traffic. Note: If an application still cannot function correctly after enabling multiple ports via th ...

  • SMC Networks SMC7004ABR - page 50

    N ETWORKING AND C LIENT S ERVICES 4-18 Misc Administrator Time-out – Enter time-out sett ing in minute fo r administration protection. Discard PING from WAN side – You can enhance your network security by preventing any host on the WAN to ping the Barricade. Remote Management – By default, management access is only available to users on your ...

  • SMC Networks SMC7004ABR - page 51

    C ONFIGURING THE B ARRICADE 4-19 Viewing Network and Device Status You can use the following screen to display WAN/LAN connection status, firmware and hardware version numbers, any illegal attempts to access your network, as well as information on all DHCP clients conn ected to your network. The following items are included in this screen: Field De ...

  • SMC Networks SMC7004ABR - page 52

    U SING S YSTEM T OOLS 4-20 Using System Tools You can use the “Tools” menu to reboot the Barricade, restore factory settings, or update firmware. The “Backup Settings” button allows you to save your Barricade’s configuration to a file named config.bin on your PC. You can then click on the “Restore Settings” button to restore the saved ...

  • SMC Networks SMC7004ABR - page 53

    5-1 C HAPTER 5 C ONFIGURI NG C LIENT TCP/IP If you have not p reviously installed the TCP/IP p rotocol on your client PCs, refer to the following section. If you need information on how to configure a TCP/IP address on a PC, refer to “Setting TCP/IP to Work with the Barricade” on page 5-3. Installing TCP/IP Protocol in Your PC 1. Click the Star ...

  • SMC Networks SMC7004ABR - page 54

    I NSTALLI NG TCP/IP P ROTOCOL IN Y OUR PC 5-2 5. Select the Microsoft item in the manufacturers list. And choose TCP/IP in the Network Proto cols. Click the OK button to return to the Netw ork window. 6. The TCP/IP prot ocol will be listed in the Network window. Click OK to complete the install procedure and restart your PC to enable the TCP/IP pro ...

  • SMC Networks SMC7004ABR - page 55

    C ONFIGURING C LIENT TCP/IP 5-3 Setting TCP/IP to Work with the Barricade 1. Click the Start butt on and choose Settin gs , then click Control Panel . 2. Double click the Network icon. Select the TCP/IP line that has been assigned to your network card in the Configuration tab of the Networ k window. 3. Click the Properties button to set t he TCP/IP ...

  • SMC Networks SMC7004ABR - page 56

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-4 Configuring Your Computer with Windows 95/98/ME You may find that the instructions here do not exactly match your version of Windows. This is because these steps and screenshots were created from Windows 98. Windows 95 and Windows Millennium Edition are very similar, but not identical, to Windows 98 ...

  • SMC Networks SMC7004ABR - page 57

    C ONFIGURING C LIENT TCP/IP 5-5 2. From "Control Panel," double-click the "Network" icon. 3. In the "Network" window, under the "Configuration " tab, double-click the "TCP/IP" entry that is listed with your network card. ...

  • SMC Networks SMC7004ABR - page 58

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-6 4. Select the "IP Address" tab. If "Obtain an IP address automatically" is already selected, your computer is already configured for DHCP. Click "Cancel" to close each window, and skip to Step 2 "Disable HTTP Proxy." 5. Locate your IP address and Subnet Mask. ...

  • SMC Networks SMC7004ABR - page 59

    C ONFIGURING C LIENT TCP/IP 5-7 7. Click the "DNS Configuration" tab. Locate the DNS servers listed under "DNS Server Search Order." Record the listed addresses. 8. After writing down your settings, check to make sure you have recorded them correctly. Click the "IP Address" tab and then click "Obtain an IP address ...

  • SMC Networks SMC7004ABR - page 60

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-8 Internet Explorer 1. Open Internet Explorer and click the stop button. Click "Tools," then "Internet Options." 2. In the "Internet Options" window click the "Connections" tab. Next, click the "LAN Settings..." button. 3. Clear all the checkboxes. 4. ...

  • SMC Networks SMC7004ABR - page 61

    C ONFIGURING C LIENT TCP/IP 5-9 Netscape 1. Open Netscape and click the stop button. Click "Edit," then click "Preferences..." 2. In the "Preferences" window, under "Category" double-click "Advanced," then click "Proxies." Select "Direct connection to the Internet." Click "O ...

  • SMC Networks SMC7004ABR - page 62

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-10 1. Click "Start," then "Run..." 2. Type "WINIPCFG" and click "OK." It may take a minute or tw o for the "IP Configuration" window to appear. 3. From the drop -down menu, select your network card. Click "Release" and then "Renew." ...

  • SMC Networks SMC7004ABR - page 63

    C ONFIGURING C LIENT TCP/IP 5-11 Configuring Your Computer with Windows 2000 Step 1. Configure TCP/IP Settings After you have completed the hardware setup, you need to configure your computer to connect to your Barricade. You also need to determine how your ISP issues your IP address. Many ISPs issue these numbers automatically, using a networking ...

  • SMC Networks SMC7004ABR - page 64

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-12 2. Double-click the "Network & Dial-Up Connections" icon. 3. Double-click the icon that corresponds to the connection to your Barricade. 4. Click "Properties." ...

  • SMC Networks SMC7004ABR - page 65

    C ONFIGURING C LIENT TCP/IP 5-13 5. Double-click "Internet Protocol (TCP/IP)." 6. All the information that you need to record is on the "Internet Protocol (TCP/IP) Properties" dialog box. Use the spaces below to record the information. If "Obtain an IP address automatically" and "Obtain DNS server address automati ...

  • SMC Networks SMC7004ABR - page 66

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-14 Step 2. Disable HTTP Proxy You will need to verify that the "HTTP Proxy" feature of your Web browser is disabled. This is so that your W eb browser will be able to view the configuration pages inside your Barricade. The following steps are for Internet Explorer and for Netscape. Determine ...

  • SMC Networks SMC7004ABR - page 67

    C ONFIGURING C LIENT TCP/IP 5-15 2. In the "Internet Options" window click the "Connections" tab. Next, click the "LAN Settings..." button. 3. Clear all the checkboxes. 4. Click "OK," and then click "OK" again to close the "Internet Options" window. Netscape 1. Open Netscape and click the ...

  • SMC Networks SMC7004ABR - page 68

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-16 2. In the "Preferences" window, under "Category" double-click "Advanced," then click "Proxies." Select "Direct connection to the Internet." Click "OK." Step 3. Obtain IP Settings From Your Barricade Now that you have configured your comput ...

  • SMC Networks SMC7004ABR - page 69

    C ONFIGURING C LIENT TCP/IP 5-17 2. In the "Comman d Prompt" window , type "IPCONFI G / RELEASE" and press the <ENTER> key. 3. Type "IPCONFIG /RENEW" and press the <ENTER> key. Verify that your IP address is now 192.168.2.xxx (2-255), your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1 ...

  • SMC Networks SMC7004ABR - page 70

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-18 Configuring Your Computer with Windows NT 4.0 Step 1. Configure TCP/IP Settings After you have completed the hardware setup, you need to configure your computer to connect to your Barricade. You need to determine how your ISP issues your IP address. Many ISPs issue these numbers automatically using ...

  • SMC Networks SMC7004ABR - page 71

    C ONFIGURING C LIENT TCP/IP 5-19 3. Select the "Protocols" tab. 4. Double-click "TCP/ IP Protocol." 5. Select the "IP Address" tab. 6. In the "Adapter" drop-down list, be sure your Ethernet adapter is selected. If "Obtain an IP address automatically" is already selected, your computer is already con ...

  • SMC Networks SMC7004ABR - page 72

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-20 7. In the "TCP/IP Properties" dialog box, click the IP address tab to locate your IP address, subnet Mask, and default gateway. Record these values in the space provided below. 8. Click the "DNS" tab to see the primary and secondary DNS servers. Record these values in the approp ...

  • SMC Networks SMC7004ABR - page 73

    C ONFIGURING C LIENT TCP/IP 5-21 Step 2. Disable HTTP Proxy You will need to verify that the "HTTP Proxy" feature of your Web browser is disabled. This is so that your W eb browser will be able to view the configuration pages inside your Barricade. The following steps are for Internet Explorer and for Netscape. Determine which browser you ...

  • SMC Networks SMC7004ABR - page 74

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-22 3. Clear all the checkboxes. 4. Click "OK," and then click "OK" again to close the "Internet Options" window. Netscape 1. Open Netscape and click the stop button. Click "Edit," then click "Preferences..." 2. In the "Preferences" window, un ...

  • SMC Networks SMC7004ABR - page 75

    C ONFIGURING C LIENT TCP/IP 5-23 Step 3. Obtain IP Settings From Your Barricade Now that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing any old IP settings and renewing them with settings from your Barricade, you will also verify that yo u have configured your computer correctly ...

  • SMC Networks SMC7004ABR - page 76

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-24 3. Type "IPCONFIG /RENEW" and press the <ENTER> key. Verify that your IP address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioning. 4. Type "EXIT" and press <ENTER> ...

  • SMC Networks SMC7004ABR - page 77

    C ONFIGURING C LIENT TCP/IP 5-25 Here is what to do: 1. Pull down the Apple Menu. Click "Control Panels" and select TCP/IP. 2. In the TCP/IP dialog box, make sure that "Ethernet" is selected in the "Connect Via:" field. ...

  • SMC Networks SMC7004ABR - page 78

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-26 If "Using DHCP Server" is already selected in the "Configure" field, your computer is already configured for DHCP. Close the TCP/IP dialog box, and skip to Step 2 "Disable HTTP Proxy." 3. All the information that you need to record is on the "TCP/IP" dialog b ...

  • SMC Networks SMC7004ABR - page 79

    C ONFIGURING C LIENT TCP/IP 5-27 Internet Explorer 1. Open Internet Explorer and click the stop button. Click "Edit" and select "Preferences." 2. In the Internet Explorer Preference s window, under Network, select Proxies. 3. Uncheck all checkboxe s and click OK. Netscape 1. Open Netscape and click the stop button. Click "E ...

  • SMC Networks SMC7004ABR - page 80

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-28 2. In the "Preferences" dialog box, In the left-hand column labeled "Category," select "Advanced." Under the "Advanced" category, select "Proxies." 3. Select "Direct Connection to the Internet" and click OK. Step 3. Obtain IP Settings From ...

  • SMC Networks SMC7004ABR - page 81

    C ONFIGURING C LIENT TCP/IP 5-29 1. Pull down the Apple Menu. Click "Control Panels" and select TCP/IP. 2. In the TCP/IP window, your new settings will be shown. Verify that your IP address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioni ...

  • SMC Networks SMC7004ABR - page 82

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-30 3. Close the TCP/IP window. Dynamic IP Allocation via a DHCP Server Select Obtain an IP address automatically in the IP Addr ess tab. Do not input any values under the Gateway tab, and choose Disable DNS in the DNS Configuration tab. These settings will be automatically configured by the DHCP serve ...

  • SMC Networks SMC7004ABR - page 83

    C ONFIGURING C LIENT TCP/IP 5-31 Manual IP Configuration 1. Select Specify an IP address in the IP Address tab. Select an IP address based on the default network 192.168.2.X (where X is between 2 and 254), and use 255 .255.255.0 f or the subnet mas k. 2. In the Gateway tab, add the IP address of the Barricade (default: 192.168.2.1) in the New gatew ...

  • SMC Networks SMC7004ABR - page 84

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-32 4. After finishing TCP/IP setup, click OK , and then reboot the computer. After that, set up other PCs on the LAN according to the procedures described above. Verifying Your TCP/IP Connection After installing the TCP/IP communication protocol and configuring an IP address in the same network with t ...

  • SMC Networks SMC7004ABR - page 85

    C ONFIGURING C LIENT TCP/IP 5-33 If you can successfully Ping the Barricade, then you are now ready to connect to the Internet! ...

  • SMC Networks SMC7004ABR - page 86

    S ETTING TCP/IP TO W ORK WIT H THE B ARRICADE 5-34 ...

  • SMC Networks SMC7004ABR - page 87

    6-1 C HAPTER 6 C ONFIGURING P RINTER S ERVICES If you want to use the print server built into the Barricade, then you must first install the Port Monitor program as described in the following section for Windows 95/98/ME/NT/2000. To configure the Barricade Print Server for Windows 95/98/ME/ NT/2000, or Unix, see “Configure the Print Server” on ...

  • SMC Networks SMC7004ABR - page 88

    I NSTALL THE P RINTER P ORT M ONITOR 6-2 2. The next screen indicates that the print client uses TCP/IP network protocol to monitor print requests. Click “Next.” 3. Select the destination folder and click on the “Next” button. The setup program will then be gin to install the programs into th e destination folder. ...

  • SMC Networks SMC7004ABR - page 89

    C ONFIGURING P RINTER S ERVICES 6-3 4. Select the Program Folder that will contain the program icon for uninstalling the port monitor, and then click “Next.” 5. Enter the prin ter port name that will be used to ident ify the port monitor in your system, and press “Next.” 6. When the setup program finishes installing the port monitor, select ...

  • SMC Networks SMC7004ABR - page 90

    C ONFIGURE THE P RINT S ERVER 6-4 Configure the Print Server The Barricade’s print server supports Microsoft Windows 95/98/ ME/NT/2000, and Unix. If you are using Windows 95/98/ME/NT/ 2000, first install the port monitor as described in the previous section before adding the Barricade’s print server to your operating system. Configure the Netwo ...

  • SMC Networks SMC7004ABR - page 91

    C ONFIGURING P RINTER S ERVICES 6-5 3. Specify the printer type attached to the Barricade. 4. Select the monitored port (the default p ort name is “SMC100”) and then click the “Configure Port” button. 5. Enter the IP address of the Barricade and click “OK,” and then click “Next” in the Add Printer Wizard dialog box. 6. Continue foll ...

  • SMC Networks SMC7004ABR - page 92

    C ONFIGURE THE P RINT S ERVER 6-6 Configure the Network Printer in Windows NT 1. On a Windows NT platform, open the “Printers” window in the My Computer menu, and double-clic k the “Add Printer” icon. 2. Follow the prompts to add a local p rinter to your system. ...

  • SMC Networks SMC7004ABR - page 93

    C ONFIGURING P RINTER S ERVICES 6-7 3. Select the monitored port. The default port name is “SMC100.” Then click the “Configure Port” button. 4. Enter the IP address of the Barricade and click “OK,” and then click “Next” in the Add Printer Wizard dialog box. 5. Specify the printer type attached to the Barricade. 6. Continue following ...

  • SMC Networks SMC7004ABR - page 94

    C ONFIGURE THE P RINT S ERVER 6-8 Configure the Network Printer in Unix Systems Follow the traditional configuration procedure on Unix platforms to set up the Barricade print server. The printer name is “lpt1.” ...

  • SMC Networks SMC7004ABR - page 95

    A-1 A PPENDIX A T ROUBLESHOOTING This appendix d escribes common problem s you may encounter and possible solutions to them. The Barricade can be easily monitored through panel i ndicators to identify p roblems. If you can not resolve any connection problems after checking the indicators, then refer to the other sections in the following table. Tro ...

  • SMC Networks SMC7004ABR - page 96

    T ROUBLESHOOTING A-2 LED Indicators Link LED is Off • Verify that the Barricade and attached device are powered on. • Be sure the cable is plugged into both t he Barricade and the corresponding device. • Verify that the proper cable type is used and that its length does not exceed the spe cified limits. • Be sure that the network interface ...

  • SMC Networks SMC7004ABR - page 97

    T ROUBLESHOOTING A-3 Management Problems Cannot connect using the Web browser • Be sure to have configured the Barricad e with a valid IP address, su bnet mask and default gateway. • Check that you have a valid network connection to the Barricade and that the port you are using has not been disable d. • Check the network cabl ing between the ...

  • SMC Networks SMC7004ABR - page 98

    T ROUBLESHOOTING A-4 ...

  • SMC Networks SMC7004ABR - page 99

    B-1 A PPENDIX B C ABLES Ethernet Cable Specifications Twisted-pair Cable Caution: DO-NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. For 10BASE-T/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two diff ...

  • SMC Networks SMC7004ABR - page 100

    C ABLES B-2 Figure B-1 illustrates how the pins on the RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. Figure B-1. RJ-45 Connector Pin Numbers Straight-through Cable Crossover Cable Straight-Through RJ-45 Pin Assignments End 1 End 2 1 (TD+) 1 (TD+) 2 (TD-) 2 (TD-) 3 (RD+) 3 ...

  • SMC Networks SMC7004ABR - page 101

    C ABLES B-3 RJ-45 Port Pin Assignments All LAN ports on the Barricade support automatic MDI/MDI-X configuration. This means that the pin signals in use will depend on whether the LAN port is operating in MDI or MDI-X mode. However, the WAN port is configured only for MDI-X mode. Pin MDI Signal Name* MDI-X Signal Name* 1 Transmit Data (TD+) Receive ...

  • SMC Networks SMC7004ABR - page 102

    C ABLES B-4 Serial Port Pin Assignments The DB-9 serial port on the rear panel is used to connect the Barricade to an ISDN TA or PSTN modem. The pin assignments used to connect to this port are provided in the following tables. Figure B-2. DB-9 Serial Port Pin Numbers DB-9 Port Pin Assignments EIA Circuit CCITT Signal Descrip tion Gateway’s DB9 D ...

  • SMC Networks SMC7004ABR - page 103

    C ABLES B-5 Serial Port to 9-Pin COM Port on PC Serial Port to 25-Pin DCE Port on Modem Serial Port to 25-Pin DTE Port on PC Barricade’s 9-Pin Serial Port CCITT Signal PC’s 9-Pin COM Port 1 DCD ----------- DCD ------------ 1 2 RXD <--------- TXD ------------ 3 3 TXD ----------- RXD ----------> 2 4 DTR ----------- DSR ----- -----> 6 5 S ...

  • SMC Networks SMC7004ABR - page 104

    C ABLES B-6 Printer Port Pin Assignments The DB-25 parallel port on the Barricade’s rear panel is used to connect the Barricade to a printer. When a printer is attached to this port, any PCs attached to the Barricade’s LAN ports can pass files to the printer. The pin assignments used to connect to the printer port are provided in the following ...

  • SMC Networks SMC7004ABR - page 105

    C-1 A PPENDIX C S PECIFICATIONS LAN Interface 10BASE-T/100BASE-TX 4 RJ-45 ports WAN Interface 10BASE-T/100BASE-TX, 1 RJ-45 port Serial, 1 RS-232 DB-9 connector Printer Interface Parallel 1 DB-25 printer port Management Web management Advanced Features Dynamic IP Address Conf iguration – DHCP, DNS Firewall – Client privileges, hacker prevention ...

  • SMC Networks SMC7004ABR - page 106

    S PECIFICATIONS C-2 Input Power 12V (1A) Maximum Current 0.04A RMS max.@110V/240V Power Consumption 5 Watts max. @ 100-240 VAC Internet Standards ARP (RFC 826), IP (RFC 791), ICMP (RFC 792 ), UDP (RFC 768), TCP (RFC 793), Telnet (RFC 854-8 59), MD5 (RFC 1321), BOOTP Extension (RFC 1497), PPP LCP Extension (RFC 1570), PPPoE (RFC 2516), NAT (RFC 1631 ...

  • SMC Networks SMC7004ABR - page 107

    S PECIFICATIONS C-3 Compliances CE Mark Emissions FCC Class B VCCI Class B Industry Canada Class B EN55022 (CISPR 22) Class B C-Tick - AS/NZS 3548 (1995) Class B Immunity EN 61000-3-2/3 EN 61000-4-2/3/4/5/6/8/11 Safety UL 1950 EN60950 (TÜV) CSA 22.2 No. 950 Warranty Limited Lifetime ...

  • SMC Networks SMC7004ABR - page 108

    S PECIFICATIONS C-4 ...

  • SMC Networks SMC7004ABR - page 109

    D-1 A PPENDIX D O RDERING I NFORMATION Barricade Broadband Router Products SMC7004ABR 4-port Residential Gateway - WAN/LAN/Print Server SMC7004AWBR 4-port Residential Gateway - WAN/LAN/WLAN/Print Server ...

  • SMC Networks SMC7004ABR - page 110

    O RDERING I NFORMATI ON D-2 ...

  • SMC Networks SMC7004ABR - page 111

    ...

  • SMC Networks SMC7004ABR - page 112

    38 T esla Irvine, CA 92618 Phone: (949) 679-8 000 Model Numbers: SMC7004ABR Rev ision Number: E022002-R02 F1.0 FO R T E CH NI CAL S UPPO RT , CAL L : F r om U .S .A. a nd Ca na da ( 24 hour s a da y, 7 da ys a w e e k) ( 800) S MC - 4- Y O U ; ( 949) 679- 8000; F a x: ( 949) 679-1481 F rom Eur ope ( 8: 00 A M - 5: 30 P M UK Tim e ) 44 ( 0) 118 974 ...

Manufacturer SMC Networks Category Network Router

Documents that we receive from a manufacturer of a SMC Networks SMC7004ABR can be divided into several groups. They are, among others:
- SMC Networks technical drawings
- SMC7004ABR manuals
- SMC Networks product data sheets
- information booklets
- or energy labels SMC Networks SMC7004ABR
All of them are important, but the most important information from the point of view of use of the device are in the user manual SMC Networks SMC7004ABR.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals SMC Networks SMC7004ABR, service manual, brief instructions and user manuals SMC Networks SMC7004ABR. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product SMC Networks SMC7004ABR.

Similar manuals

A complete manual for the device SMC Networks SMC7004ABR, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use SMC Networks SMC7004ABR by users. Manuals are usually written by a technical writer, but in a language understandable to all users of SMC Networks SMC7004ABR.

A complete SMC Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual SMC Networks SMC7004ABR - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the SMC Networks SMC7004ABR, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the SMC Networks SMC7004ABR, that we can find in the current document
3. Tips how to use the basic functions of the device SMC Networks SMC7004ABR - which should help us in our first steps of using SMC Networks SMC7004ABR
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with SMC Networks SMC7004ABR
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of SMC Networks SMC7004ABR in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning SMC Networks SMC7004ABR?

Use the form below

If you did not solve your problem by using a manual SMC Networks SMC7004ABR, ask a question using the form below. If a user had a similar problem with SMC Networks SMC7004ABR it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)