English dropdown-ico

Manual Field Controls UV-E

8 pages 0.55 mb
Download

Go to site of 8

Summary
  • Field Controls UV-E - page 1

    UV-AIRE™ AIR PURIFYING SYSTEM Mode l: UV -E (For use with 12”, 18” and 28” Fiel d Controls Lamp s) (120/240 volt application) READ THESE INSTRUCTIONS CAREFULLY AND COMPLETE LY BEFORE PROCEEDING WITH THE INSTALLATION LEAVE THE INSTALLATION INSTRUCTIONS WITH THE OWNER/OPERATOR OF THE DEVICE AFTER OPENING THE CARTON, UNPACK AND INSPECT THE UNI ...

  • Field Controls UV-E - page 2

    Page 2 Figure 1 I. GENERAL INFORMATION This product is not sold as a medical device and is not for the purpose of diagnosis of any disease o r condition nor for use in the mitigation, treatment, or pr evention of any disease or condition. There are different size units avail able, depending on t he squ are footage of your home. See ch art below for ...

  • Field Controls UV-E - page 3

    Page 3 WARNING : Disconnect electrical power supply b efore wirin g 9. Connect to an approp riate power source such as an AC power di sconnect box or to a circuit breaker pan el. (See Figure 8) 10. Determine le ngth of wire and cond ui t necessary according to power co nnect ion and instal l wiring conduit and water tight connector as sh own in exa ...

  • Field Controls UV-E - page 4

    Page 4 15. Determine whether to use flat or angled bra cket. (Ref er to UV-Aire Configurations in Section III for aid in this decision) a. Flat Bracket Installation i. Remove the two hex nuts and flat bra cket from included bagged hardware. ii. Install the flat bracket a nd secure to the unit ba se with the hex nuts provided. (See Figure 10) b. Ang ...

  • Field Controls UV-E - page 5

    Page 5 18. Swing secu ring bracket over en d of lamp and h and-tighten the provided wi ng nut on stud. (See Figure 13) 19. Plug ballast plug into end of lamp and reconnect power supply. (See Figure 14) 20. Flip the red power switch to the on position. (Light on swit ch should be on indicating power.) 21. Loo k through view port to be sure lamp is w ...

  • Field Controls UV-E - page 6

    Page 6 III. BULB MOUNTING BRACKET SEL ECTION AND INSTALLATION The UV-AIRE TM units come with an a ngled mounting bracket and flat mo unting bracket to position th e bulb either straight or at an angle. Cho ose one or the other br acket method be st suited for your needs. Refer to th e configurations chart below when making your selection. A NGLED L ...

  • Field Controls UV-E - page 7

    Page 7 IV. MAINTENANCE 1. Inspect and clean lamp at least every 6 months. 2. Replace your UV-Aire™ Ai r Purifying System lamp once a year to maintain the lamps maximum output intensity. The lamp should operate continuously fo r maximum lamp life and light effectiveness. V. REPLACEMEN T PROCEDURE VERY IMPORTANT: Turn switch on unit to ‘OFF’ po ...

  • Field Controls UV-E - page 8

    Page 8 VIII. FLEX DUCT INSTALLATION For installations on duct system s with a metallic main duct an d flex duct branches , follow the instructions in figure 15 below. The health aspects associa ted with the use of these products and t heir ability to aid in disinfecting of environmen tal air have not been investiga ted by UL. P/N 46427300 Rev E 05/ ...

Manufacturer Field Controls Category Air Cleaner

Documents that we receive from a manufacturer of a Field Controls UV-E can be divided into several groups. They are, among others:
- Field Controls technical drawings
- UV-E manuals
- Field Controls product data sheets
- information booklets
- or energy labels Field Controls UV-E
All of them are important, but the most important information from the point of view of use of the device are in the user manual Field Controls UV-E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Field Controls UV-E, service manual, brief instructions and user manuals Field Controls UV-E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Field Controls UV-E.

Similar manuals

A complete manual for the device Field Controls UV-E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Field Controls UV-E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Field Controls UV-E.

A complete Field Controls manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Field Controls UV-E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Field Controls UV-E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Field Controls UV-E, that we can find in the current document
3. Tips how to use the basic functions of the device Field Controls UV-E - which should help us in our first steps of using Field Controls UV-E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Field Controls UV-E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Field Controls UV-E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Field Controls UV-E?

Use the form below

If you did not solve your problem by using a manual Field Controls UV-E, ask a question using the form below. If a user had a similar problem with Field Controls UV-E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)