English dropdown-ico

Manual Fujitsu D5200

53 pages 0.92 mb
Download

Go to site of 53

Summary
  • Fujitsu D5200 - page 1

    i ESPRIMO D5200 User’s Manual Fujitsu endeavours to ensure that the information in this document is correct, but accepts no liability for any error or omission. Any procedures described in this document for operating Fujitsu products should be read and understood by the operator before such products are used. To ensure that Fujitsu products funct ...

  • Fujitsu D5200 - page 2

    ii IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product nea ...

  • Fujitsu D5200 - page 3

    iii 13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally when the operating i ...

  • Fujitsu D5200 - page 4

    iv Before Reading this Manual This section describes safety precautions and convention used in this manual. Be sure to read this. For Safe Operation This manual contains important information for using the ESPRIMO personal computer. Read this manual thoroughly before using your PC. In particular, “Safety Precautions” in this manual must be read ...

  • Fujitsu D5200 - page 5

    v Microsoft Service Pack Microsoft Corp. offers Service Pack to provide the users of Microsoft ® Windows ® with more stable system operation (http://www.microsoft.com/). The latest version of the Service Pack helps you configure the most stable system using Microsoft ® Windows ® provided at that time by Microsoft Corp. We recommend you to use t ...

  • Fujitsu D5200 - page 6

    vi 6. Modification and reverse engineering You may not modify the Software or reverse engineer the Software by decompiling or disassembling. shall the third party or developer warrant the Software. 7. High level of safety The Software is designed for general use, i.e., for office use, personal use and home use, but not designed or manufactured for ...

  • Fujitsu D5200 - page 7

    vii Conventions Used in this Manual Introduction This manual tells you how to put your PC into operation and how to operate it in daily use. Depending on the configuration level chosen some of the hardware components described may not be available on your PC. Please observe the notes on your operating system. You can incorporate operable drives (fo ...

  • Fujitsu D5200 - page 8

    viii Important Notes In this chapter you will find information regarding safety which is essential to take note of when working with your PC. The manufacturer's notes contain helpful information on your PC.  Safety CAUTION During installation and before operating the device, please observe the instructions on environmental conditions in the ...

  • Fujitsu D5200 - page 9

    ix  FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation. NOTE: This equipment has been tested and found to comply with the limits for a "Class B" digital device, pursuant ...

  • Fujitsu D5200 - page 10

    x  Transporting the PC CAUTION Transport all parts separately in their original packaging or in a packaging which protects them from knocks and jolts, to the new site. Do not unpack them until all transportation manoeuvres are completed. Never drop the monitor!  Cleaning the PC CAUTION Turn off all power and equipment switches and remove the ...

  • Fujitsu D5200 - page 11

    xi  Disposal and recycling Disposal of the PC unit Disposal of the PC unit (including accessories except the LCD unit) is controlled by the Waste Disposal and Public Cleaning Law. To institutional and corporate customers Personal computers must be disposed off as industrial waste. Institutional and corporate customers are obliged to entrust an a ...

  • Fujitsu D5200 - page 12

    xii WARNING • Before mounting or dismounting an optional unit in/from your PC, switch off the PC and all connected units. Unplug all power cords from respective outlets to prevent electric shock and unplug all data communication cables from the respective outlets. Warning and Caution Labels Your PC bears the warning and caution labels as shown be ...

  • Fujitsu D5200 - page 13

    xiii Before Reading This Manual Chapter 1 Preparing for Use This chapter provides the names and functions of individual parts. Chapter 2 Operation This section describes the location of installation and installation of the computer. Chapter 3 Troubleshooting and Tips This chapter provides the basic information on the PC and operation. Chapter 4 Sys ...

  • Fujitsu D5200 - page 14

    xiv Contents CHAPTER 1 Preparing for Use Preparing for Use .............................................................................. 1 Unpacking and Chec king the Deliver y ............................................................. 1 Steps f or Initial Setup ................................................................................... ...

  • Fujitsu D5200 - page 15

    1 Chapter 1 - Preparing for Use CAUTION Please take note of the safety information in the "Important notes" chapter. ■ Unpacking and Checking the Delivery It is recommended not to throw away the original packaging material! It may be required for reshipment at some later date. ● Unpack all the individual parts. ● Check the delivery ...

  • Fujitsu D5200 - page 16

    2 ■ Setting Up the PC CAUTION When installing your PC, give consideration to the recommendations and safety notes. Set up the PC only in its correct orientation. The points to observe are illustrated on the following pages. Do not expose the PC to extreme environmental conditions and protect it from dust, humidity and heat. When installing the PC ...

  • Fujitsu D5200 - page 17

    3  Vertical positioning When this personal computer is vertically installed away from a wall, install the feet with the following steps. 1 Align the feet to the width of the main unit of the personal computer. 2 Install the feet on the main unit of the personal computer. Secure them in the screw holes on the back of the feet with screws. D5200_1 ...

  • Fujitsu D5200 - page 18

    4  Horizontal positioning 1 Disassemble the foot. 2 Place the main unit of the personal computer on the disassembled foot. D5200_1(01-10) 12/7/06, 10:58 am 4 ...

  • Fujitsu D5200 - page 19

    5      POINT  For vertical installation, the main unit of the personal computer can be installed by fitting the five rubbers attached to the four corners and center of the main unit of the personal computers. When installing rubbers, secure them in the positions where the foot does not touch when it is vertically installed. Wipe d ...

  • Fujitsu D5200 - page 20

    6 ■ Connect the Monitor, Mouse and Keyboard The ports for monitor, mouse and keyboard are on the rear and on the front of the system unit. PS/2 keyboard port / purple PS/2 mouse port / green Monitor port / blue USB port / black  Connecting the keyboard Connecting standard keyboard Use the supplied keyboard cable only. ● Plug the round keyboa ...

  • Fujitsu D5200 - page 21

    7 ■ Initial Switch-on: Software will be Installed If the PC is connected to a network, the network protocol is required as well as the user and server details. Contact your network administrator if you have any questions about these settings. When you switch on your PC for the first time, the supplied software is installed and configured. You sho ...

  • Fujitsu D5200 - page 22

    8 ■ Connecting External Devices CAUTION Do not connect or disconnect cables during a thunderstorm. Always take hold of the actual plug. Never unplug a cable by pulling the cable itself. Connect and disconnect the cables in the order described below. With the exception of USB devices, always remove all power plugs before connecting external device ...

  • Fujitsu D5200 - page 23

    9  Connections on the system unit The ports for external devices are on the rear and on the front of the system unit. The ports available on your PC depend on the configuration level you have selected. The standard ports are marked with the symbols shown below (or similar). Keyboard port / purple PS/2 mouse port / green 1 Serial interface 1 / tu ...

  • Fujitsu D5200 - page 24

    10  Connecting external devices to the serial port External devices can be connected to the serial port (e.g. a modem). ● Connect the data cable to the external device. ● Connect the data cable to the serial port . For an exact description of how to connect external devices to the serial port , please refer to the device documentation. ● S ...

  • Fujitsu D5200 - page 25

    11 Chapter 2 - Operation  Switching On the PC ● If necessary, switch the monitor on (see the operating manual for the monitor). ● Switch the PC on with the main power switch on the rear of the PC. ● Press the ON/OFF switch on the front of the PC. The power-on indicator lights green and the PC is started.  Switching Off the PC ● Shut d ...

  • Fujitsu D5200 - page 26

    12 ■ Front Panels of the Main Unit of the Personal Computer 1 Vent On the top of the computer there is an opening through which heat is forcibly discharged from the computer. Note that the vent must not be blocked by objects. When placed horizontally, position the computer at a location where the vent is more than 20 cm away from the wall. 2 Powe ...

  • Fujitsu D5200 - page 27

    13 4 Disc access indicator Lights up when data is being written to the hard disk, or when data are read from the hard disk/ Optical drive or when an audio CD is played. Some optical drives may light up when access is made to the a CD. 5 USB ports Used to connect USB peripherals to your computer. The ports are USB 2.0 compliant. 6 Microphone jack ( ...

  • Fujitsu D5200 - page 28

    14 ■ Back Panel of the Main Unit of the Personal Computer 1 Power Outlet Used to connect the power cable to the monitor. 2 Power Inlet Used to connect the power cable. 3 Key hole for a padlock Install a commercially available key. 4 Half-Height expansion card slot Insert the expansion card to expand the functions of the personal computer. Expansi ...

  • Fujitsu D5200 - page 29

    15 6 Main switch Turn "Off" when completely turning off the power to the main unit of the computer. The " | " side is "On" and the "O" side is "Off". If it is set to "Off", the main unit of the personal computer is not powered on even when pressing the power supply button. However, if you ...

  • Fujitsu D5200 - page 30

    16 ■ Keyboard 1 Esc key Pressing this key cancels the operation the application program is executing. 2 F keys These F keys are assigned specific functions for each application. 3 Back space key Press the Back Space key to move the cursor to the left while deleting characters. 4 Insert key Press the Insert key to switch between character insert m ...

  • Fujitsu D5200 - page 31

    17 9 Ctrl key Use the Ctrl key in combination with another key. Its function varies with each application. 10 Windows key Press the Windows key to display the Start menu. 11 Alt key Use the Ctrl key in combination with another key. Its function varies with each application. 12 Application key This key has the same function as clicking the right mou ...

  • Fujitsu D5200 - page 32

    18  Floppy Disks Note: Applicable only for units bundled with Slim Optical or Slim Floppy Drive Combo.  Working with Floppy Disks Follow the instructions supplied by the vendor of the floppy disks. Never clean the floppy disk drives with cleaning disks. Any attempt would destroy the read/ write head in the disk drive within 20 seconds. 1 Inse ...

  • Fujitsu D5200 - page 33

    19 ■ Anti-theft Protection and Lead-sealing There are three ways to protect your PC from theft: ● With the Kensington Lock device (1) and with a Kensington MicroSaver ● With a chain (lead-seal) ● With a (pad)lock To prevent unauthorised persons from opening the casing, the casing can be sealed. To do this, feed the sealing chain through the ...

  • Fujitsu D5200 - page 34

    20 Chapter 3 - Troubleshooting and Tips CAUTION Take note of the safety notes and in the "Preparing for use" chapter, when you connect or disconnect cables. If a fault occurs, try to correct it as described in the following sections: ● in this chapter ● in the documentation of the connected devices ● in the help systems of the softw ...

  • Fujitsu D5200 - page 35

    21  The screen stays blank If your screen remains blank this may be due to the following: Monitor is switched off ● Switch your monitor on. Power saving has been activated (screen is blank) ● Press any key on the keyboard. or ● Deactivate the screen saver. Enter the appropriate password. Brightness control is set to dark ● Adjust the bri ...

  • Fujitsu D5200 - page 36

    22 Wrong monitor has been set under Window XP ● Restart the PC. ● Press [ F8 ] while the system is booting. Either the Windows Advanced Start Options menu or the menu for selecting the operating system appears. ● If the menu for selecting the operating system appears, press [ F8 ]. ● Select Safe Mode or Safe Mode with Network. ● Set the c ...

  • Fujitsu D5200 - page 37

    23 ■ Time and/or Date is not Correct You can set the time and date in the BIOS Setup or in the operating system. ● Set the time and date. If the time and date are repeatedly wrong when you switch on your PC, the on-board battery is flat. CAUTION. Do not touch the on-board battery. Risk of electric shock, burn and fire. Do not replace the on-boa ...

  • Fujitsu D5200 - page 38

    24 Chapter 4 - System Expansion CAUTION It may be necessary to update the BIOS when carrying out a system expansion or hardware upgrade. When installing components that heats up easily, make sure that the maximum permissible temperatures of the individual components are not exceeded. The PC must be switched off when installing/removing the system e ...

  • Fujitsu D5200 - page 39

    25 ■ Before Connecting Peripheral Devices Your computer can be expanded by connecting or incorporating various peripheral devices. WARNING  When connecting peripheral devices to your computer, do not connect devices other than Fujitsu recommended products. Doing so could result in an electronic shock, fire, or failure. CAUTION  When install ...

  • Fujitsu D5200 - page 40

    26 ● Do not disassemble the power unit. The power unit is a box-shaped device located at the rear of the internal main unit of the personal computer. ● Precautions on handling internal cables or devices Do not scratch or machine internal cables or devices. ● Taking precautions to static electricity The printed board and electronic devices in ...

  • Fujitsu D5200 - page 41

    27 ■ Removing the Main Unit Cover When connecting peripheral devices, remove the upper cover so that the internal of the computer is exposed.  How to remove the main unit cover When the foot is installed, remove the foot from the main unit of the personal computer to place the computer in the horizontal position before removing the upper cover ...

  • Fujitsu D5200 - page 42

    28 ■ Installing Memory      POINT  When installing memory after the purchase, turn off your computer once after the setup of Windows, then install memory. WARNING  Before installing or removing memory, turn off the computer and connected devices, and unplug the computer. Otherwise, you might get an electric shock.  Before ...

  • Fujitsu D5200 - page 43

    29  Locations for memory to be installed To install memory, insert it into the memory slot of the main unit of the personal computer.  Memory to be installed When installing additional memory, use Fujitsu recommended parts only. ● Table of combinations of memory When installing memory, check the following Table for the combination of the me ...

  • Fujitsu D5200 - page 44

    30  Installing memory IMPORTANT  Hold the edge of the memory as shown in the following figure. Be sure not to touch the areas (pins) with the indication of golden lines.  When installing or removing memory, take care so that the memory does not touch auxiliary fittings. 1 Unplug your computer. 2 Remove the power plug, LAN and modular cable ...

  • Fujitsu D5200 - page 45

    31 5 Open the hooks on the both sides of the slot outward. 6 Insert the slot into the memory. Align the notch of the memory to the notch of the slot, and vertically insert the memory into the slot. When the memory is correctly inserted, the hooks on the both sides of the slot are raised. Make sure that the hooks firmly hold the memory. D5200_4(24-3 ...

  • Fujitsu D5200 - page 46

    32 7 Install the upper cover. 8 Connect power plugs, LAN and modular cables.      POINT  When removing the memory, refer to installing Steps. Store the removed memory in a safe place.  Note that the hooks on the both sides of the slot should not be strongly forced opened. Forced opening may cause the memory to jump, resulting i ...

  • Fujitsu D5200 - page 47

    33 ■ Installing the Expansion Card      POINT  Shut off your computer after the initial Windows setup before proceeding to installing expansion card. WARNING  Before installing or removing expansion cards, turn off the computer and connected devices, and unplug the computer. Otherwise, you might get an electric shock.  Bef ...

  • Fujitsu D5200 - page 48

    34  Locations for expansion cards to be installed To install an expansion card, insert it into the expansion card slot of the main unit of the personal computer. 1 Slide the lock buttons on the both sides of the main unit of the personal computer to the front of it and remove the upper cover. Slide the lock buttons to the main unit of the person ...

  • Fujitsu D5200 - page 49

    35  Installing expansion cards 1 Unplug your computer. 2 Remove power plugs, LAN and modular cables from respective outlet. 3 Remove the upper cover. 4 Remove the installing fittings. Raise the installing fitting upward. When an expansion card has already been installed, pull out the cable connected to the installed expansion card before removin ...

  • Fujitsu D5200 - page 50

    36      POINT  Store the removed slot cover in a safe place. When using an expansion card after removed, install so that dust does not enter the internal personal computer. 7 Insert the expansion card into the port. Firmly insert the expansion card into the port and secure it by returning the lock raised in Step 4. 8 Install the i ...

  • Fujitsu D5200 - page 51

    37 Electrical Data Rated voltage range: (selectable) Frequency: Max. rated current • Casing Dimensions Width/ depth/ height: Weight with the basic configuration Environmental conditions Environment class 3K2 Environment class 2K2 Temperature: • Operating (3K2) • Transport (2K2) Condensation in operating must be avoided. Clearance required to ...

  • Fujitsu D5200 - page 52

    38 *1 : Some application may show the other name of this processor. *2 : The capacity of the disk provided in this manual is calculated by that 1 MB=1000 x 1000 bytes and 1 GB=1000 x 1000 x 1000 bytes. With the calculation that 1 MB=1024 x 1024 bytes and 1 GB=1024 x 1024 x 1024 bytes, the capacity actually displayed on Windows becomes less than the ...

  • Fujitsu D5200 - page 53

    39 D5200_5(33-39) 12/7/06, 11:00 am 39 ...

Manufacturer Fujitsu Category Personal Computer

Documents that we receive from a manufacturer of a Fujitsu D5200 can be divided into several groups. They are, among others:
- Fujitsu technical drawings
- D5200 manuals
- Fujitsu product data sheets
- information booklets
- or energy labels Fujitsu D5200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fujitsu D5200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fujitsu D5200, service manual, brief instructions and user manuals Fujitsu D5200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fujitsu D5200.

Similar manuals

A complete manual for the device Fujitsu D5200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fujitsu D5200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fujitsu D5200.

A complete Fujitsu manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fujitsu D5200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fujitsu D5200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fujitsu D5200, that we can find in the current document
3. Tips how to use the basic functions of the device Fujitsu D5200 - which should help us in our first steps of using Fujitsu D5200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fujitsu D5200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fujitsu D5200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fujitsu D5200?

Use the form below

If you did not solve your problem by using a manual Fujitsu D5200, ask a question using the form below. If a user had a similar problem with Fujitsu D5200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)