English dropdown-ico

Manual Genie NI 5421

36 pages 0.31 mb
Download

Go to site of 36

Summary
  • Genie NI 5421 - page 1

    NI 5421 Specifications NI PXI/PCI-5421 16-Bit 100 MS/s Arbitrary Waveform Generator Unless otherwise noted, the followi ng conditions were used for each specification: • Analog Filter enabled. • Interpol ation set to maximum allo wed factor f or a gi v en sample r ate. • Signals terminated with 50 Ω . • Direct Path set to 1 V pk-p k , Lo ...

  • Genie NI 5421 - page 2

    NI 5421 Specifications 2 ni.com CH 0 (Channel 0 Analog Output , Front Panel Connector) Table 1. Specif ication Va l u e Comments Number of Channels 1 — Connector SMB (jack) — Output Voltage Characteristics Output Paths 1. The software-selectable Ma in Output Path setting provides full-scale v oltages from 12.00 V pk-pk to 5.64 mV pk-pk into a 5 ...

  • Genie NI 5421 - page 3

    © National Instruments Corpor ation 3 NI 5421 Specifications Amplitude and Of fset Amplitude Range Pat h Load Amplitude (V pk-pk ) 1. Amp litude values assume the full scale of the D A C is utilized. If an amplitude smaller than the minimu m va lu e i s desired, then wa veforms le ss than full scale of the D A C can be used. 2. NI-F GEN compensate ...

  • Genie NI 5421 - page 4

    NI 5421 Specifications 4 ni.com Maximum Output Voltage Maximum Output Vo l t a g e Pat h Load Maximum Output V oltage (V pk -pk ) The Max imum Output V oltage of the NI 5421 is determined by the Amplitude Range and the Of fset Range. Direct 50 Ω ±0.500 1 k Ω ±0.953 Open ±1.000 Low- Gain Amplif ier 50 Ω ±1.000 1 k Ω ±1.905 Open ±2.000 ...

  • Genie NI 5421 - page 5

    © National Instruments Corpor ation 5 NI 5421 Specifications Output Coupling DC — Output Enable Software-selectable. When disabl ed, CH 0 out is terminated with a 1 W resistor with a value equal to the selected output impedance. — Maximum Output Overload The CH 0 output can be connected to a 50 Ω , ±12 V (±8 V for the Direct Path) s ource ...

  • Genie NI 5421 - page 6

    NI 5421 Specifications 6 ni.com Figure 1. Normalized Pas sband Flatness, Direct Path Figure 2. Pulse Response, Low-Gai n Amplifier Path 50 Ω Load 1.0M 10.0M 48.0M –10.0 –9.0 –6.0 –8.0 –5.0 –7.0 –3.0 –2.0 –1.0 0.0 1.0 2.0 F requency (Hz) dB –4.0 +0.3 dB –0.4 dB –0.4 dB +0.4 dB +0.6 dB –0.4 dB Guaranteed Specification Typi ...

  • Genie NI 5421 - page 7

    © National Instruments Corpor ation 7 NI 5421 Specifications Table 1. (Continued) Specification Va l u e Comments Suggested Maximum Frequencies for Common Funct ions Function Path Disable the Analog Filter and the Digital Interpolation Filter for S quare, Ramp, and T riangle. Direct Lo w-Gain Amplifier High-Gain Amplifier Sine 43 MHz 43 MHz 43 MHz ...

  • Genie NI 5421 - page 8

    NI 5421 Specifications 8 ni.com Spectral Characteristics (Continued) Spurious-Free Dynamic Range (SFDR) with Harmonics Path Amplitude –1 dBFS. Measured from DC to 50 MHz. Also called harmonic distortion. SFDR with harmonics at low amplitudes is limited by a –148 dBm/Hz noise floor . All values are typical and include aliased harmonics. Direct L ...

  • Genie NI 5421 - page 9

    © National Instruments Corpor ation 9 NI 5421 Specifications Spectral Characteristics (Continued) 0 º C to 40 º C T otal Harmonic Distortion (THD) Path Amplitude –1 dBFS. Includes the 2 nd through the 6 th harmonic. Direct Lo w-Gain Amplifier High-Gain Amplifier 20 kHz –77 dBc (typical) –77 dBc (typical) –77 dBc (typical) 1 MHz –75 dBc ...

  • Genie NI 5421 - page 10

    NI 5421 Specification s 10 ni.com A verage Noise Density Pat h Amplitude Range A verage Noise Density A verage Noise Density at small amplitudes is limited by a –148 dBm/Hz noise floor . V pk-pk dBm dBm/Hz dBFS/ Hz Direct 1 4.0 18 –142 –146.0 Lo w Gain 0.06 –20.4 9 –148 –127.6 Lo w Gain 0.1 –16.0 9 –148 –132.0 Lo w Gain 0.4 –4 . ...

  • Genie NI 5421 - page 11

    © National Instruments Corpor ation 11 NI 5421 Specifications Figure 3. 10 MHz Single-T one Spectrum , Direct Path, 100 MS/s, Interpolation Factor S et to 4 Note The noise floor in Figure 3 is lim ited by the measurement de vice. Refer to the Average Noise Density specif ication. 0.0 25.0M 50.0M 75.0M 100.0M 125.0M 158.0M 175.0M 200.0M –90.0 – ...

  • Genie NI 5421 - page 12

    NI 5421 Specification s 12 ni.com Figur e 4. 10 MHz Single-T one Spectrum, Low -Gain Amplifier Path, 100 MS/s, Interpolation Factor Set to 4 Note The noise floor in Figure 4 is lim ited by the measurement de vice. Refer to the Average Noise Density specif ication. 0.0 25.0M 50.0M 75.0M 100.0M 125.0M 150.0M 175.0M 200.0M –90.0 –80.0 –50.0 –7 ...

  • Genie NI 5421 - page 13

    © National Instruments Corpor ation 13 NI 5421 Specifications Figure 5. Direct Path, 2-T one Spectrum (T ypical) Note The noise floor in Figure 5 is lim ited by the measurement de vice. Refer to the Average Noise Density specif ication. 0.0 25.0M 50.0M 75.0M 100.0M 125.0M 150.0M 175.0M 200.0M –90.0 –80.0 –50.0 –70.0 –40.0 –60.0 –30.0 ...

  • Genie NI 5421 - page 14

    NI 5421 Specification s 14 ni.com Sample Clock Table 2. Specif ication Va l u e Comments Sources 1. Internal, Di vide-by- N ( N ≥ 1) 2. Internal, DDS-based, High-Resolution 3. External, CLK IN (SMB front panel connector) 4. External, DDC CLK IN (DIGIT AL D A T A & CONTR OL front panel conn ector) 5. NI PXI-5421 : External, P XI Star trigger ( ...

  • Genie NI 5421 - page 15

    © National Instruments Corpor ation 15 NI 5421 Specifications Effective Sample Rate Sample Rate (MS/s) Interpolation Factor Ef fecti ve Sample Rate Ef fecti ve Sample Rate = (Interpolation Factor) * (Sample Rate) 10 S/s to 105 MS/s 1 (Off) 10 S/s to 105 MS/s 12.5 MS/s to 105 MS/s 2 25 MS/s to 210 MS/s 10 MS/s to 100 MS/s 4 40 MS/s to 400 MS/s 10 M ...

  • Genie NI 5421 - page 16

    NI 5421 Specification s 16 ni.com System Phase Noise and Jitter (10 MHz Carrier) Sample Clock Source System Phase Noise Density (dBc/Hz) Offset System Output Jitter (Integrated from 100 Hz to 100 kHz) 1. High- Resolution specifications increase as the Sample Rate is decreased. 2. NI PXI-5421 PXI Star trigger specification is v alid when the Sample ...

  • Genie NI 5421 - page 17

    © National Instruments Corpor ation 17 NI 5421 Specifications Onboard Clock (Internal VCXO) Sample Clock Exporting Exported Sample Clock Destinations 1. PFI<0..1> (SMB front panel connectors) 2. DDC CLK OUT (DIGIT AL D A T A & CONTR OL front panel connector) 3. NI PXI-5421 —PXI_T rig<0..7> (backplane connecto r) NI PCI-5421 —R ...

  • Genie NI 5421 - page 18

    NI 5421 Specification s 18 ni.com Phase-Locked Loop (PLL) Reference Clock Table 4. Specif ication Va l u e Comments Sources 1. NI PXI-5421 —PXI_CLK10 (backplane connector) NI PCI-5421 —R TSI_7 (R TSI_CLK) 2. CLK IN (SMB fro nt panel connector) The PLL Reference Clock provides the reference frequenc y for the phase-locked loop. Frequenc y Accura ...

  • Genie NI 5421 - page 19

    © National Instruments Corpor ation 19 NI 5421 Specifications CLK IN (Sample Clock and Reference Cloc k Input, Front Panel Connector) Table 5. Specif ication Va l u e Comments Connector SMB (jack) — Direction Input — Destinations 1. Sample Clock 2. PLL Reference Clock — Frequenc y Range 1 MHz to 105 MHz (Sample Clock destination and sine wa ...

  • Genie NI 5421 - page 20

    NI 5421 Specification s 20 ni.com PFI 0 and PFI 1 (Programmable Function Interfac e, Front Panel Connectors) Table 6. Specif ication Va l u e Comments Connectors T wo SMB (jack) — Direction Bi-directional — Frequenc y Range DC to 105 MHz — As an Input (Trigger) Destinations Start T rigger — Maximum Input Overload –2 V to +7 V — V IH 2.0 ...

  • Genie NI 5421 - page 21

    © National Instruments Corpor ation 21 NI 5421 Specifications V OH Minimum: 2.9 V (open load), 1.4 V (50 Ω load) Output driv ers are +3.3 V TTL compatible. Measured with a 1 m cable. V OL Maximum: 0.2 V (open load), 0.2 V (50 Ω load) Rise/F all T ime (20% to 80%) ≤ 2.0 ns Load of 10 pF . Table 6. (Cont inued) Specif ication Va l u e Comments ...

  • Genie NI 5421 - page 22

    NI 5421 Specification s 22 ni.com DIGIT AL DA T A & CONTROL (DDC) Optional Front Panel Connector Table 7. Specif ication Va l u e Comments Connector T ype 68-pin VHDCI female receptacle — Number of Data Output Signals 16 — Control Signals 1. DDC CLK OUT (clock output) 2. DDC CLK IN (clo ck input) 3. PFI 2 (input) 4. PFI 3 (input) 5. PFI 4 ( ...

  • Genie NI 5421 - page 23

    © National Instruments Corpor ation 23 NI 5421 Specifications Output Signal Characteristics (Continued) Output Skew T ypical: 1 ns, maxim um 2 ns. Ske w between any two outp uts on the DIGIT AL DA T A & CONTR OL front panel connector . — Output Enable/Disabl e Controlled through the so ftware on all Data Output Signals and Control Signals co ...

  • Genie NI 5421 - page 24

    NI 5421 Specification s 24 ni.com Start T rigger DDC CLK IN Clocking For ma t DDC Data Output signals change on the rising edge of DDC CLK IN. — Frequenc y Range 10 Hz to 105 MHz — Input Duty Cycle T olerance 40% to 60% — Input Jitter T olerances 300 ps pk-pk of Cycle-Cycle Jitter, and 1 ns rms of Period Jitter . — Table 8. Specif ication V ...

  • Genie NI 5421 - page 25

    © National Instruments Corpor ation 25 NI 5421 Specifications Delay from Start T rigger to CH 0 Analog Output Interpolation Factor T ypical Delay Refer to t s2 at NI Signal Generators Help»Devices» NI 5421» NI <bus>-5421» Triggering» Trigger Timing . Digital Inter polation F ilter disabled. 43 Sample Clock Periods + 110 ns 2 57 Sample C ...

  • Genie NI 5421 - page 26

    NI 5421 Specification s 26 ni.com Markers Table 9. Specif ication Va l u e Comments Destinations 1. PFI<0..1> (SMB front panel connectors) 2. PFI<4..5> (DIGIT AL D A T A & CON TR OL front panel connector) 3. NI PXI-5421 —PXI_T rig<0..6> (backplane connector) NI PCI-5421 —R TSI<0..7> — Quantity One Marker per Se gme ...

  • Genie NI 5421 - page 27

    © National Instruments Corpor ation 27 NI 5421 Specifications W aveform and Instruction Memor y Utilization Table 10. Specif ication Va l u e Comments Memory Usage The NI 5421 uses the Synchronization and Memory Core (SMC) technology in which wav eforms and instructions share onboard memory . Parameters, such as number of segments in sequence list ...

  • Genie NI 5421 - page 28

    NI 5421 Specification s 28 ni.com Loop Count 1 to 16,777,21 5. Burst trigger: Unlimited — Quantum W aveform size must be an integer multiple of four samp les. — Memory Limits 8 MB Standard 32 MB Optio n 256 MB Option All trigger modes except where noted. Arbitrary W av eform Mode, Maximum W av eform Memory 4,194,176 Samples 16,777,088 Samples 1 ...

  • Genie NI 5421 - page 29

    © National Instruments Corpor ation 29 NI 5421 Specifications Calibration Power Table 11. Specif ication Va l u e Comments Self-Calibrati on An onboard, 24-bit ADC and precision voltage reference are used to calibrate the DC gain and offset. The self-calibration is initiated by the user through the software and takes approximately 75 s econds to c ...

  • Genie NI 5421 - page 30

    NI 5421 Specification s 30 ni.com Software Table 13. Specif ication Va l u e Comments Dri ver Software NI-FGEN 2.0 or later ve rsion. NI-FGEN is an IVI-compliant driv er that all o ws you to configure, control, and calibrate the NI 5421. NI -FGEN prov ides application programming interfaces fo r man y de velopment en vironment s. — Application So ...

  • Genie NI 5421 - page 31

    © National Instruments Corpor ation 31 NI 5421 Specifications Environment NI PXI-5421 Environment Note T o ensure that the NI PXI-5421 cools ef fectively , follo w the guidelines in the Maintain Forced-Air Cooling Note to Users incl uded in the NI 542 1 kit. The NI PXI-5421 is intended for indoor use only . Table 14. Specifications Va l u e Comm e ...

  • Genie NI 5421 - page 32

    NI 5421 Specification s 32 ni.com NI PCI-5421 Environment Note T o ensure that the NI PCI-5421 cools ef fectively , follo w the guidelines in the Maintain Forced -Air Cooling Note to Users included in the NI 5421 kit. Also, to maximize airflo w and extend the life of the de vice, lea ve any adjacent PCI slots empty . The NI PCI-5421 is intended for ...

  • Genie NI 5421 - page 33

    © National Instruments Corpor ation 33 NI 5421 Specifications Safety , Electromagnetic Compatibility , and CE Compliance Table 16. Specification Va l u e Comments Safety The NI 5421 is designed to meet th e requireme nts of the following standards of safety for electrical equi pment for measurement, contro l, and laboratory use: IEC 61010-1, EN 6 ...

  • Genie NI 5421 - page 34

    NI 5421 Specification s 34 ni.com Physical Table 17. Specif ication Va l u e Comments Dimensions NI PXI-5421 NI PCI-5421 — 3U, One Slot, PXI/cPCI Module 2.0 × 13.0 × 21.6 cm (0.8 × 5.1 × 8.5 inches) 34.07 × 10.67 × 2.03 cm (13.4 × 4.20 × 0.8 inches) We i g h t 345 g (12.1 oz) 419 g (14 .8 oz) — Front Panel Connectors Label Functio n(s) ...

  • Genie NI 5421 - page 35

    © National Instruments Corpor ation 35 NI 5421 Specifications NI PXI-5421 Only—Front Panel LED Indicators Label Function For more informat ion, refer to the NI Sig nal Generators Help. A CCESS LED The A C CESS LED indicates the status of the PCI b us and the interface from the NI 5421 to the controller . A CTIVE LED The A C TIVE LED indicates th ...

  • Genie NI 5421 - page 36

    National Instruments, NI, ni.com, and LabVIEW are tradem arks of National Instruments Corporation. Refer to t he Terms of Use section on ni.com/legal for mor e information abou t National Instruments trademarks. Other product and compan y names mentioned herein are trademarks or trade names of their respective companie s . For patents covering Nati ...

Manufacturer Genie Category Portable Generator

Documents that we receive from a manufacturer of a Genie NI 5421 can be divided into several groups. They are, among others:
- Genie technical drawings
- NI 5421 manuals
- Genie product data sheets
- information booklets
- or energy labels Genie NI 5421
All of them are important, but the most important information from the point of view of use of the device are in the user manual Genie NI 5421.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Genie NI 5421, service manual, brief instructions and user manuals Genie NI 5421. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Genie NI 5421.

Similar manuals

A complete manual for the device Genie NI 5421, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Genie NI 5421 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Genie NI 5421.

A complete Genie manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Genie NI 5421 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Genie NI 5421, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Genie NI 5421, that we can find in the current document
3. Tips how to use the basic functions of the device Genie NI 5421 - which should help us in our first steps of using Genie NI 5421
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Genie NI 5421
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Genie NI 5421 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Genie NI 5421?

Use the form below

If you did not solve your problem by using a manual Genie NI 5421, ask a question using the form below. If a user had a similar problem with Genie NI 5421 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)