-
Renesas SH7147 - page 1
Revision Date: Feb. 28, 2007 Renesas Microcomputer Deve lopment Environment System SuperH ™ Family / SH7147 Series R0E571470CFK00 Rev.5.00 SH7147 Group PLQP010 0KB-A User System Interface Boa rd User’s Manual REJ10J1211-0500 ...
-
Renesas SH7147 - page 2
...
-
Renesas SH7147 - page 3
1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any ...
-
Renesas SH7147 - page 4
...
-
Renesas SH7147 - page 5
I IMPORTANT INFORMATION READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use t he emulator pro duct until you fully understand its mechanism. Emulator Pr oduct: Throughout this document , the term "emulator product" shall be def ...
-
Renesas SH7147 - page 6
II Target User of the Emulator Pr oduct: This emulator product should only be us ed by those who have carefull y read and thoroughly understood the informat ion and restrict ions containe d i n the user's manual. Do not attempt to us e the emulator product until you fu lly understand its mechanism. It is highl y recommended that first-t ime us ...
-
Renesas SH7147 - page 7
III LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifica tions and free from defects in material and/or workmanship. Rene sas, at its option, will replace any emulator products returned intact to the factory, transportation charges prepaid, which Renesas, upon inspection, shall determine ...
-
Renesas SH7147 - page 8
IV State Law : Some states do n ot allow the exclu sion or limitatio n of implied warranties or liability for incidental or consequent ial damages, so t he a bove limitati on or exclusion may not appl y to you. This warranty gi ves you specific l egal rights, a nd you may have other rights whi ch may vary from state to state. The Warranty is Vo id ...
-
Renesas SH7147 - page 9
V SAFETY PAGE READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use t he emulator pro duct until you fully understand its mechanism. DEFINITI ON OF SIGNAL WORDS Either in the user's manual or on the produc t, several icons are used to ...
-
Renesas SH7147 - page 10
VI means WARNING or CAUTIO N. Example: CAUTION AG AINST AN ELECT RIC SHOCK means PROHIBITIO N. Example: DISASSEMBLY PROHIBIT ED means A FORCIBLE ACT ION. Example: UNPLUG T HE POWER CABLE F ROM THE R ECEPTACLE. ...
-
Renesas SH7147 - page 11
VII W ARNING Warnings for AC Power Supply: • If the att ached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. • Use an AC power cable which complies with the safety standard of the country. • Do not touch the plug of the AC power c ...
-
Renesas SH7147 - page 12
VIII W ARNING • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet. D o not use this as it is because of the danger of electric shock and/or fire. In this case, contact your local distributor. • When installing or connecti ...
-
Renesas SH7147 - page 13
IX CA UTION Cautions for AC Adapte r: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. Do not use it for other product. • The DC plug on the included AC adapter has the below polarity. • The included AC adapter has no power supply switch. The AC adapter is always act ive while conne ...
-
Renesas SH7147 - page 14
X W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or rem odel the emulator product by yourself for electric shock prevent ion and quality assurance. 2. Always switch ...
-
Renesas SH7147 - page 15
i Preface The R0E571470CFK00 is a user system interface boa rd that connects a user system for the SH7147 PLQP 0100KB-A (former code: F P-100UV) package to the SH 7147 E200F emulator (R0E0200F1EMU00 or R0E571470VKK00). ...
-
Renesas SH7147 - page 16
ii ...
-
Renesas SH7147 - page 17
iii Contents Section 1 Configuration .....................................................................................1 Section 2 Environmental Conditions .................................................................3 Section 3 User In terface Speci fications .............................................................5 Section 4 Connectio ...
-
Renesas SH7147 - page 18
iv ...
-
Renesas SH7147 - page 19
1 Section 1 Configuration Figure 1 and table 1 show the conf iguration and component s of the user syst em interface board for the PLQP0100KB -A (former code: FP-100UV) package. P lease make sure you have all of t hese components when unpacking. Board Screws (M2.0 x 10 mm) Spacer IC socket User system Screws (M2.0 x 6 mm) Socket cover EV-chip unit ...
-
Renesas SH7147 - page 20
2 CA UTION Use a NQPACK 100SD-ND socket (manufactured by Tokyo Eletech Corporation) and a HQPACK100SD (manuf actured by Tokyo Eletech Corporation) for the PLQP0100KB- A (former code: FP-100UV) package IC socket and socket cover, respectively, on the user system. Table 1 R0E571470CFK00 Com ponents No. Component Quantity Remarks 1 Board 1 With four s ...
-
Renesas SH7147 - page 21
3 Section 2 Environmental Conditions Maintain the condit ions in table 2 w hen using the emulator. Table 2 Environmenta l Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Vibration Operating: 2.45 m/s 2 max. Storage: 4. ...
-
Renesas SH7147 - page 22
4 ...
-
Renesas SH7147 - page 23
5 Section 3 User Interface Specifications This user syst em interface board has the function that masks the chip select si gnals (CS0 and CS1), bus reques t signal (BR EQ), and wait input signal (WAIT) depending on the s etting of a switch. To use the mask function, set the switch (SW 1 ) on the user system interface board (figure 2), according to ...
-
Renesas SH7147 - page 24
6 Table 3 Setting a Switch (SW1) Switch Setting SW1 No. PLQP0100KB-A (Former Code: FP-100UV) Socket Pin No. Signal Name On Off 1 58 PA9/_WAIT/TCLKD/_POE8/TXD2 Mask canceled Mask enabled 2 47 PB1/_BREQ/TIC5W/HR XD1 Mask canceled Mask enabled 3 42 PB6/_WAIT/HTXD0 Mask canceled Mask enabled 4 41 PB7/_CS1/HRX D0 Mask canceled Mask enabled 5 18 PE10/_CS ...
-
Renesas SH7147 - page 25
7 Section 4 Connection Procedures 4.1 Connecting User System Int erface Board to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connect ed to or removed from any part. B efore connect ing, make sure that pin 1 on both sides are correct ly aligned. Failure to do so will resu ...
-
Renesas SH7147 - page 26
8 4.1.2 Installing Ca ble Head CA UTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a PLQP 0100KB-A (former code: F P-100UV) package on the user system with pin 1 on the user s ystem interface boa rd, and insert the us er system interface board into the IC socket on the user s ystem, as shown in figure 4. 4.1.3 Fa ...
-
Renesas SH7147 - page 27
9 Board Screws (M2.0 x 10 mm) User system IC sock et (NQP A CK100SD-ND man ufactured b y T oky o Eletech Corporation) Pin 1 Figure 4 Connecting User System In terface Board to User System ...
-
Renesas SH7147 - page 28
10 4.2 Connecting User System Interf ace Board to EV-Chip Board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF t he user system and the emulat or product before ...
-
Renesas SH7147 - page 29
11 Board Spacer User system EV-chip unit Connector No. User I/F Connector 1 (CN4) EV-Chip Unit Connector No. Board Connector No. UCN1 UCN2 User I/F Connector 2 (CN5) Figure 5 Connecting User System Interface Board to EV-Chip Board ...
-
Renesas SH7147 - page 30
12 4.3 Recommended Dimensions for Us er System Mount Pad (Footprint) Figure 6 shows the recommended dimensions for the mount pad (footprint ) for the user syst em with an IC s ocket for a PLQP0100KB -A (former code: FP-100UV) package (NQPACK 100SD-ND: manufactured by Tokyo El etech Corporation). N ote that the dimens ions in figure 6 are somewhat d ...
-
Renesas SH7147 - page 31
13 4.4 Dimensions for External Bus Tr ace Unit, Emulation Memory Unit, EV-Chip Unit, and User S ystem Interface Board The dimensions for the external bus trace unit, em ulation memory unit, EV-c hip unit, and the us er system interface board are shown in figure 7. ...
-
Renesas SH7147 - page 32
14 125.0 90.0 90.0 45.0 5.0 125.0 90.0 110.0 20.0 30.0 60.0 5.0 125.0 90.0 Unit: mm Tolerance: ±0.5 mm External bus trace unit Board Spacer EV-chip unit Pin 1 Emulation memory unit Figure 7 Dimensions for External Bus Tra ce Unit, Emulation Memory Unit, EV-Chip Unit, and User System Interface Board ...
-
Renesas SH7147 - page 33
15 4.5 Resulting Dimensions after Conn ecting User System Interface Board The resulting dimensions, after conn ecting the user system interface board to the us er system, are shown in figures 8, 9, and 10. 24.5 55.0 12.5 68.4 30.0 37.5 27.5 29.2 24.5 39.19 39.19 24.5 IC socket (NQPACK100SD-ND manufactured by Tokyo Eletech Corporation) User system S ...
-
Renesas SH7147 - page 34
16 24.5 42.1 12.5 55.5 30.0 37.5 27.5 29.2 IC socket (NQPACK100SD-ND manufactured by Tokyo Eletech Corporation) User system Pin 1 Top view Spacer ( φ 6.0) Unit: mm Tolerance: ±1.0 mm 24.5 39.19 39.19 24.5 External bus trace unit EV-chip unit Figure 9 Resu lting Dim ensions after Co nnecting User System Interface Board (when Connecting External Bu ...
-
Renesas SH7147 - page 35
17 24.5 29.2 12.5 42.6 30.0 37.5 27.5 EV-chip unit Spacer ( φ 6.0) IC socket (NQPACK100SD-ND manufactured by Tokyo Eletech Corporation) User system Unit: mm Tolerance: ±1.0 mm 24.5 39.19 39.19 24.5 Pin 1 Top view Figure 10 Resu lting Dim ensions after Co nnecting User System Interface Board (when Connecting EV-Chip Unit ) ...
-
Renesas SH7147 - page 36
18 ...
-
Renesas SH7147 - page 37
19 Section 5 Installing the MCU to the User System CA UTION 1. Check t he location of pin 1 before insert ing. 2. Use a Philips-type screwdr iver whose head matches the screw head. 3. The tightening t orque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when the f orce required to turn th e screw ...
-
Renesas SH7147 - page 38
20 MCU (SH7147) Screws (M2.0 x 6 mm) Socket cover Pin 1 User system IC socket (NQPACK100SD-ND manufactured by Tokyo Eletech Corporation) Figure 11 Insta lling MCU to User Syst em ...
-
Renesas SH7147 - page 39
21 Section 6 Verifying Operation 1. Turn on the emulator according to the pro cedures described in the SH -2A, SH-2 E200F Emulator User' s Manual (R0E0200F1EMU 00E or R0E571470EMU00E). 2. The emulator connected to this user syst em interface board supports three kinds of clock sources as t he MCU clock. For detail s, refer to the SH7080 E200F ...
-
Renesas SH7147 - page 40
22 ...
-
Renesas SH7147 - page 41
23 Section 7 Notice 1. Before connecting any part s or cables, make s ure that pin 1 on the both si des are correctly aligned. 2. Do not apply excessive force to the us er syst em interface board while it is connected to the user sy stem. 3. The dimensions of the recommended mount pad for the IC s ocket for this user s ystem interface board are dif ...
-
Renesas SH7147 - page 42
24 ...
-
Renesas SH7147 - page 43
SH7147 Group PLQP0100KB-A User System Interface Board User's Manual Publication Date: Rev. 1.00, December 9, 2004 Rev. 5.00, February 28, 2007 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2007. Renesas Technology Corp., ...
-
Renesas SH7147 - page 44
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) ...
-
Renesas SH7147 - page 45
...
-
Renesas SH7147 - page 46
SH7147 Group PLQP0100KB- A User System Interface Board User’s Manual ...
У вас вопрос, касающийся Renesas SH7147?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Renesas SH7147, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Renesas SH7147 со всей вероятностью он захочет поделиться методом ее решения.