-
Miele DA 2050 - page 1
Operating and installation instructions Cooker hood DA 2050 To avoid the risk of accidents or damage to this appliance it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 07 306 730 en - GB, AU, NZ ...
-
Miele DA 2050 - page 2
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Guide to the ...
-
Miele DA 2050 - page 3
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and can normally be recycled. Packaging e.g. cling film, polystyrene and plastic wrappings must be kept out of the reach of babies and young children. Danger of suffocation! Dispose of or recycle al ...
-
Miele DA 2050 - page 4
This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on the safety, i ...
-
Miele DA 2050 - page 5
~ Before connecting the appliance to the mains supply, make sure that the voltage and frequency details given on the data plate correspond with the on-site electricity supply, otherwise the appliance could be damaged. Consult a qualified electrician if in any doubt. ~ The electrical safety of this appliance can only be guaranteed when continuity is ...
-
Miele DA 2050 - page 6
~ Do not connect the appliance to the mains electricity supply by a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating). ~ This appliance may only be used in mobile installations such as ships, caravans, aircraft etc. if a risk assessment of the installation has been carri ...
-
Miele DA 2050 - page 7
In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure of 0.04 mbar (4 pa) is the maximum permissible in the room. Ventilation can be maintained by air inlets which must not be blocked, in wi ...
-
Miele DA 2050 - page 8
~ Do not use the cooker hood without the filters in place. This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation. ~ The filters should be regularly cleaned or changed as appropriate. Saturated filters are a fire hazard. See "Cleaning and care". ~ Do not use a steam-cleaner to cle ...
-
Miele DA 2050 - page 9
The cooker hood works with . . . air extraction: The air is drawn in, cleaned by the grease filter and then directed outside. If the on-site ventilation system does not have a non-return flap , then the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. Having a non-return flap fitted in the ducting ...
-
Miele DA 2050 - page 10
a Lighting switch b Fan switch c Hob lighting d Charcoal filters Special accessory for recirculation mode e Grease filter Guide to the appliance 10 ...
-
Miele DA 2050 - page 11
To switch the lighting on and off The hob lighting a can be switched on and off independently of the fan. "0" - lighting off "1" - lighting on To switch the fan on ^ Turn switch b for the fan to "1". To select a power level You can select one of three power levels with switch b depending on how much the air needs to be ...
-
Miele DA 2050 - page 12
Before any cleaning or maintenance work is carried out, disconnect the cooker hood from the mains supply. Ensure that: – it is switched off at the isolator, or – it is switched off at the wall socket and the plug removed, or – the fuse is withdrawn from the fused spur connection unit, or – the mains fuse is withdrawn, or – the screw-out f ...
-
Miele DA 2050 - page 13
To avoid damaging the filter or the hob below, make sure you hold the filter securely at all times when handling it. Cleaning the grease filter by hand ^ Clean the filter with a soft nylon brush in a mild solution of hot water and a small amount of washing-up liquid. Do not use undiluted washing up liquid. Do not use: – cleaning agents containing ...
-
Miele DA 2050 - page 14
Fitting and replacing the charcoal filters If the cooker hood is connected for recirculation, two charcoal filters must be inserted in addition to the grease filter. They are designed to absorb cooking odours and are fitted in the canopy above the grease filter. New filters can be purchased from your Miele Dealer / Chartered Agent or from the Miele ...
-
Miele DA 2050 - page 15
Changing a halogen lamp Before any cleaning or maintenance work is carried out, disconnect the cooker hood from the mains supply. Ensure that: – it is switched off at the isolator, or – it is switched off at the wall socket and the plug removed, or – the fuse is withdrawn from the fused spur connection unit, or – the mains fuse is withdrawn ...
-
Miele DA 2050 - page 16
Safety distance between hob and cooker hood When planning the installation height of your cooker hood, the minimum safety distance between the top of a cooker or hob and the bottom of the cooker hood is as follows, unless a greater distance is specified by the manufacturer of your cooking appliance: Electric cookers / hobs: 450 mm (GB), 600 mm (AU, ...
-
Miele DA 2050 - page 17
– When deciding on the safety distance between the hob and cooker hood, please note that a distance of 650 mm above electric cookers/hobs may be preferable to give more working space under the hood. – Account should also be taken of the height of the person who will be using the hood most often. The person should have sufficient space to work c ...
-
Miele DA 2050 - page 18
Fitting the non-return flap (Air extraction mode only) ^ If a non-return flap is not present in the venting system, the non-return flap supplied must be fitted onto the exhaust socket in the motor unit. The flaps must open upwards. Building in The cooker hood is intended to be built into wall units, cooker hood housing units, and above breakfast ba ...
-
Miele DA 2050 - page 19
Recirculation If site conditions are not suitable for the cooker hood to be used with air extraction, the appliance must be set up for recirculation. For this, conversion kit DUU 151 (available from your Miele dealer or the Miele Spare Parts Dept.) is required. You will also need two charcoal filters (see “Technical data”). ^ Dismantle the non- ...
-
Miele DA 2050 - page 20
, Important: To avoid the danger of toxic fumes, please observe the Warning and Safety instructions. This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room. The cooker hood should be installed according to local and national building regulations. Seek approval from ...
-
Miele DA 2050 - page 21
Important: If the exhaust ducting is to run through rooms, ceiling space etc. where there may be great variations in temperature between the different areas, the problem of condensation will need to be addressed. The exhaust ducting will need to be suitably insulated. Condensate trap (optional extra) In addition to insulating the exhaust ducting, w ...
-
Miele DA 2050 - page 22
All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable. Ensure power is not supplied to the appli ...
-
Miele DA 2050 - page 23
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer / Chartered Agent or – The Miele Customer Contact Centre (see back cover for address). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. These are shown on the dat ...
-
Miele DA 2050 - page 24
Total connected load ..........1 8 5W - Fan motor ..................8 5W - Hob lighting ..............2x5 0W Voltage ................. A C2 3 0V Frequency ................. 5 0H z Fuse rating ....................5A Electrical cable length .........1 . 5m Weight .......................8k g Fan performance Extraction power according to EN 61591 Extra ...
-
Miele DA 2050 - page 25
25 ...
-
Miele DA 2050 - page 26
26 ...
-
Miele DA 2050 - page 27
27 ...
-
Miele DA 2050 - page 28
Alteration rights reserved / 4209 M.-Nr. 07 306 730 / 03 ...
У вас вопрос, касающийся Miele DA 2050?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Miele DA 2050, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Miele DA 2050 со всей вероятностью он захочет поделиться методом ее решения.