Bedienungsanleitung Graco 3A1495C

16 Seiten 1.33 mb
Download

Zur Seite of 16

Summary
  • Graco 3A1495C - page 1

    Repair Instructions LD Grease Pump Repair Kits 3A1495C Instructions for repairing the LD Grease Pump. Maximum Fluid Press ure - 7500 psi (51. 7 MPa, 517 bar) Maximum Air Pressur e - 150 psi (1. 03 MPa, 10.3 bar) Repair Kits: 24H854: Throat and Piston Seal Replacement Kit 24H856: O-Ring and S eal Replacement Kit 24U984: Air Piston Replacement Kit Im ...

  • Graco 3A1495C - page 2

    Warnings 2 3A1495C Warnings The following warnings are fo r the setup, use, grounding, mainte nance, and repair of th is equipment. The exclama- tion point symbol alerts you to a genera l warning and the ha zard symbols refer to procedure-specific r isks. When these symbols appear in the body of this manual, refe r ba ck to these Warnings. Product- ...

  • Graco 3A1495C - page 3

    Instructions 3A1495C 3 Instructions Always use all new parts included in your kit an d dis- pose of replaced parts according to all state and local regulations for disposal of discarded components. Inspect all parts when disassem bling the pump. Replace any and all worn an d damaged pa rts. Pressure Relief Procedure 1. Close the pump’s bleed-type ...

  • Graco 3A1495C - page 4

    Instructions 4 3A1495C 4. Secure a strap wrench around the shovel cylinde r (27). Use the strap wrench to turn the shovel cylin- der counte r-clockwise to loosen and r emove it fro m the pump assem bly (Fig. 2). NOTE: After a few turns, the shovel c ylinder should be loose enough to finish turning it with yo ur hand to remove this pa rt. 5. Use an ...

  • Graco 3A1495C - page 5

    Instructions 3A1495C 5 8. If the gasket (30) is still inside the spacer cylinder (36) use a pick to remove. 9. Secure a strap wrench around the spacer cylinder (36) and use it to turn the cylinder cou nter clockwise to loosen and remove it from the fla nge (22) (Fig. 6). NOTE: After a few turns, the spacer cylinder should be loose en ough to finish ...

  • Graco 3A1495C - page 6

    Instructions 6 3A1495C force to hold the pump in position. The pump cylin- der is aluminum and could be dama ged by using excessive clamping force. 16. Using a 10 mm socke t wr ench, remove the 4 screws (43) from the air valve (40) and complete ly remove air valve assembly from air cyl inder (21). Also remove the two cover gaskets 18 ). If you are ...

  • Graco 3A1495C - page 7

    Instructions 3A1495C 7 Pump Reassembly NOTE: The following instructions d escribe the proce- dure to follow to reassemble a complet ely disassemb led LD grease pump. Depending on the rep air/maintenance procedure you are perfor ming on the pump, it may not be entirely disassembled . Se e the specific section(s) related to your repair/r eplacement k ...

  • Graco 3A1495C - page 8

    Instructions 8 3A1495C 6. Install the 5 screws (4) wrench tight only. NOTE: If installing a new ai r cylinder (27), the mat- ing holes are not th readed by desig n. Use thread forming scre ws (4) to f orm thread s as they ar e being installed. Torque to 95-105 in.-lbs (10.7 - 11.8 N.m) to ensure full thread formation. 7. To ensure there is a prop e ...

  • Graco 3A1495C - page 9

    Instructions 3A1495C 9 17. Screw the piston rod (23) an d the connecting rod (32) togeth er aligning the pin hole in both pieces to allow the pin to be pushed through (Fig. 19 ). 18. Replace the pin (8 ). Use a rubber hamm er to tap the pin into plac e, being ca refu l to make sure the sides of the pin a re flush with t he outside surface of the co ...

  • Graco 3A1495C - page 10

    Instructions 10 3A1495C intake seal on the priming rod as sh own in Fig. 20. 26. Install seal retainer (29) over p riming rod (34) (Fig. 22). 27. Use an adjustable wr ench to tighten seal retaine r securely, then tor que to 45 - 55 ft lbs (61 - 75 N.m). 28. Install the priming pisto n (35 and nut (19) (Fig. 3, Fig. 4) on priming rod (3 4) Use an ad ...

  • Graco 3A1495C - page 11

    Instructions 3A1495C 11 Throat and Piston Seal Replacement Kit - 24H854 ( Fig. 25 ) Replacement parts for o-ring ( 5) installed on air piston (15), o-rings (6 and 12) installed in bottom cover ( 14), o-ring (7), u-cup seal (11) and gasket (30) installed on flange (22), pin (8) used to reassemble r od sections, and gasket (18) used later in r eassem ...

  • Graco 3A1495C - page 12

    Instructions 12 3A1495C 4. Remove nut retainer (37) from flange (22) (Fig. 28). 5. Remove u-cup seal (1 1) from flange (22) (Fig. 29 ). Grease and replace th e u-cup seal with the new p art included in the ki t and install them in the order shown in Fig. 29. NOTE: • The bearing (31) is no t included in the kit. This part is reused. The bearing ca ...

  • Graco 3A1495C - page 13

    Instructions 3A1495C 13 1. Disassemble the pump following Disassembly Steps 1-14 (pages 3-5) only. 2. Use a pick to remove the gasket (30) installed between the flange (22) and tu be (36) (Fig. 32). Grease the new gasket included in the kit and install it inside the flange. 3. Use a pick to rem ove the othe r gasket (30) installed between the cylin ...

  • Graco 3A1495C - page 14

    Instructions 14 3A1495C 3. Pull spac er cylinder ( 36) away f rom pump to access pin (8) (Fig. 36). 4. Use a rubber hammer an d small punch to drive the pin (8) out. 5. Unscrew the pump low er from di splacement rod (25). Set aside pump lower for reasse mbly. 6. Use a pick to remove gasket (30) from inside the flange (22). 7. Continue pump disass e ...

  • Graco 3A1495C - page 15

    Instructions 3A1495C 15 Fig. 38. 4. Remove pilot valve (20) from the old air cylinde r (21). Apply a light coat of grease to o-rings. 5. Install pilot valve (20) in to new air cylinder included in the kit (Fig. 39). To rq ue to 95-1 05 in. lbs (10.7-11.9 N.m). 6. Apply a thin co at of grease to o-rings (5) and o-ring on bottom co ver (14). I nstall ...

  • Graco 3A1495C - page 16

    All written and visual data contained in this document reflects the latest product info r mation available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents. Original instructions. This m anual contains English . MM3A1495 Graco Headquarters: Minne apo ...

Produzent Graco Kategorie Water Pump

Dokumente, die wir vom Produzenten des Geräts Graco 3A1495C erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Graco
- Bedienungsanleitungen 3A1495C
- Produktkarten Graco
- Informationsbroschüren
- oder Energieetiketten Graco 3A1495C
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Graco 3A1495C.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Graco 3A1495C, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Graco 3A1495C. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Graco 3A1495C ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Graco 3A1495C, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Graco 3A1495C hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Graco 3A1495C verständlich ist.

Eine gänzliche Bedienungsanleitung von Graco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Graco 3A1495C bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Graco 3A1495C befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Graco 3A1495C, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Graco 3A1495C - die uns die ersten Schritte während der Nutzung von Graco 3A1495C erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Graco 3A1495C hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Graco 3A1495C im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Graco 3A1495C?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Graco 3A1495C nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Graco 3A1495C hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)