English dropdown-ico

Manual Graco 3A1495C

16 pages 1.33 mb
Download

Go to site of 16

Summary
  • Graco 3A1495C - page 1

    Repair Instructions LD Grease Pump Repair Kits 3A1495C Instructions for repairing the LD Grease Pump. Maximum Fluid Press ure - 7500 psi (51. 7 MPa, 517 bar) Maximum Air Pressur e - 150 psi (1. 03 MPa, 10.3 bar) Repair Kits: 24H854: Throat and Piston Seal Replacement Kit 24H856: O-Ring and S eal Replacement Kit 24U984: Air Piston Replacement Kit Im ...

  • Graco 3A1495C - page 2

    Warnings 2 3A1495C Warnings The following warnings are fo r the setup, use, grounding, mainte nance, and repair of th is equipment. The exclama- tion point symbol alerts you to a genera l warning and the ha zard symbols refer to procedure-specific r isks. When these symbols appear in the body of this manual, refe r ba ck to these Warnings. Product- ...

  • Graco 3A1495C - page 3

    Instructions 3A1495C 3 Instructions Always use all new parts included in your kit an d dis- pose of replaced parts according to all state and local regulations for disposal of discarded components. Inspect all parts when disassem bling the pump. Replace any and all worn an d damaged pa rts. Pressure Relief Procedure 1. Close the pump’s bleed-type ...

  • Graco 3A1495C - page 4

    Instructions 4 3A1495C 4. Secure a strap wrench around the shovel cylinde r (27). Use the strap wrench to turn the shovel cylin- der counte r-clockwise to loosen and r emove it fro m the pump assem bly (Fig. 2). NOTE: After a few turns, the shovel c ylinder should be loose enough to finish turning it with yo ur hand to remove this pa rt. 5. Use an ...

  • Graco 3A1495C - page 5

    Instructions 3A1495C 5 8. If the gasket (30) is still inside the spacer cylinder (36) use a pick to remove. 9. Secure a strap wrench around the spacer cylinder (36) and use it to turn the cylinder cou nter clockwise to loosen and remove it from the fla nge (22) (Fig. 6). NOTE: After a few turns, the spacer cylinder should be loose en ough to finish ...

  • Graco 3A1495C - page 6

    Instructions 6 3A1495C force to hold the pump in position. The pump cylin- der is aluminum and could be dama ged by using excessive clamping force. 16. Using a 10 mm socke t wr ench, remove the 4 screws (43) from the air valve (40) and complete ly remove air valve assembly from air cyl inder (21). Also remove the two cover gaskets 18 ). If you are ...

  • Graco 3A1495C - page 7

    Instructions 3A1495C 7 Pump Reassembly NOTE: The following instructions d escribe the proce- dure to follow to reassemble a complet ely disassemb led LD grease pump. Depending on the rep air/maintenance procedure you are perfor ming on the pump, it may not be entirely disassembled . Se e the specific section(s) related to your repair/r eplacement k ...

  • Graco 3A1495C - page 8

    Instructions 8 3A1495C 6. Install the 5 screws (4) wrench tight only. NOTE: If installing a new ai r cylinder (27), the mat- ing holes are not th readed by desig n. Use thread forming scre ws (4) to f orm thread s as they ar e being installed. Torque to 95-105 in.-lbs (10.7 - 11.8 N.m) to ensure full thread formation. 7. To ensure there is a prop e ...

  • Graco 3A1495C - page 9

    Instructions 3A1495C 9 17. Screw the piston rod (23) an d the connecting rod (32) togeth er aligning the pin hole in both pieces to allow the pin to be pushed through (Fig. 19 ). 18. Replace the pin (8 ). Use a rubber hamm er to tap the pin into plac e, being ca refu l to make sure the sides of the pin a re flush with t he outside surface of the co ...

  • Graco 3A1495C - page 10

    Instructions 10 3A1495C intake seal on the priming rod as sh own in Fig. 20. 26. Install seal retainer (29) over p riming rod (34) (Fig. 22). 27. Use an adjustable wr ench to tighten seal retaine r securely, then tor que to 45 - 55 ft lbs (61 - 75 N.m). 28. Install the priming pisto n (35 and nut (19) (Fig. 3, Fig. 4) on priming rod (3 4) Use an ad ...

  • Graco 3A1495C - page 11

    Instructions 3A1495C 11 Throat and Piston Seal Replacement Kit - 24H854 ( Fig. 25 ) Replacement parts for o-ring ( 5) installed on air piston (15), o-rings (6 and 12) installed in bottom cover ( 14), o-ring (7), u-cup seal (11) and gasket (30) installed on flange (22), pin (8) used to reassemble r od sections, and gasket (18) used later in r eassem ...

  • Graco 3A1495C - page 12

    Instructions 12 3A1495C 4. Remove nut retainer (37) from flange (22) (Fig. 28). 5. Remove u-cup seal (1 1) from flange (22) (Fig. 29 ). Grease and replace th e u-cup seal with the new p art included in the ki t and install them in the order shown in Fig. 29. NOTE: • The bearing (31) is no t included in the kit. This part is reused. The bearing ca ...

  • Graco 3A1495C - page 13

    Instructions 3A1495C 13 1. Disassemble the pump following Disassembly Steps 1-14 (pages 3-5) only. 2. Use a pick to remove the gasket (30) installed between the flange (22) and tu be (36) (Fig. 32). Grease the new gasket included in the kit and install it inside the flange. 3. Use a pick to rem ove the othe r gasket (30) installed between the cylin ...

  • Graco 3A1495C - page 14

    Instructions 14 3A1495C 3. Pull spac er cylinder ( 36) away f rom pump to access pin (8) (Fig. 36). 4. Use a rubber hammer an d small punch to drive the pin (8) out. 5. Unscrew the pump low er from di splacement rod (25). Set aside pump lower for reasse mbly. 6. Use a pick to remove gasket (30) from inside the flange (22). 7. Continue pump disass e ...

  • Graco 3A1495C - page 15

    Instructions 3A1495C 15 Fig. 38. 4. Remove pilot valve (20) from the old air cylinde r (21). Apply a light coat of grease to o-rings. 5. Install pilot valve (20) in to new air cylinder included in the kit (Fig. 39). To rq ue to 95-1 05 in. lbs (10.7-11.9 N.m). 6. Apply a thin co at of grease to o-rings (5) and o-ring on bottom co ver (14). I nstall ...

  • Graco 3A1495C - page 16

    All written and visual data contained in this document reflects the latest product info r mation available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents. Original instructions. This m anual contains English . MM3A1495 Graco Headquarters: Minne apo ...

Manufacturer Graco Category Water Pump

Documents that we receive from a manufacturer of a Graco 3A1495C can be divided into several groups. They are, among others:
- Graco technical drawings
- 3A1495C manuals
- Graco product data sheets
- information booklets
- or energy labels Graco 3A1495C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco 3A1495C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco 3A1495C, service manual, brief instructions and user manuals Graco 3A1495C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco 3A1495C.

Similar manuals

A complete manual for the device Graco 3A1495C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco 3A1495C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco 3A1495C.

A complete Graco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco 3A1495C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco 3A1495C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco 3A1495C, that we can find in the current document
3. Tips how to use the basic functions of the device Graco 3A1495C - which should help us in our first steps of using Graco 3A1495C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco 3A1495C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco 3A1495C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco 3A1495C?

Use the form below

If you did not solve your problem by using a manual Graco 3A1495C, ask a question using the form below. If a user had a similar problem with Graco 3A1495C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)