Graco 3A1495Cの取扱説明書

16ページ 1.33 mb
ダウンロード

ページに移動 of 16

Summary
  • Graco 3A1495C - page 1

    Repair Instructions LD Grease Pump Repair Kits 3A1495C Instructions for repairing the LD Grease Pump. Maximum Fluid Press ure - 7500 psi (51. 7 MPa, 517 bar) Maximum Air Pressur e - 150 psi (1. 03 MPa, 10.3 bar) Repair Kits: 24H854: Throat and Piston Seal Replacement Kit 24H856: O-Ring and S eal Replacement Kit 24U984: Air Piston Replacement Kit Im ...

  • Graco 3A1495C - page 2

    Warnings 2 3A1495C Warnings The following warnings are fo r the setup, use, grounding, mainte nance, and repair of th is equipment. The exclama- tion point symbol alerts you to a genera l warning and the ha zard symbols refer to procedure-specific r isks. When these symbols appear in the body of this manual, refe r ba ck to these Warnings. Product- ...

  • Graco 3A1495C - page 3

    Instructions 3A1495C 3 Instructions Always use all new parts included in your kit an d dis- pose of replaced parts according to all state and local regulations for disposal of discarded components. Inspect all parts when disassem bling the pump. Replace any and all worn an d damaged pa rts. Pressure Relief Procedure 1. Close the pump’s bleed-type ...

  • Graco 3A1495C - page 4

    Instructions 4 3A1495C 4. Secure a strap wrench around the shovel cylinde r (27). Use the strap wrench to turn the shovel cylin- der counte r-clockwise to loosen and r emove it fro m the pump assem bly (Fig. 2). NOTE: After a few turns, the shovel c ylinder should be loose enough to finish turning it with yo ur hand to remove this pa rt. 5. Use an ...

  • Graco 3A1495C - page 5

    Instructions 3A1495C 5 8. If the gasket (30) is still inside the spacer cylinder (36) use a pick to remove. 9. Secure a strap wrench around the spacer cylinder (36) and use it to turn the cylinder cou nter clockwise to loosen and remove it from the fla nge (22) (Fig. 6). NOTE: After a few turns, the spacer cylinder should be loose en ough to finish ...

  • Graco 3A1495C - page 6

    Instructions 6 3A1495C force to hold the pump in position. The pump cylin- der is aluminum and could be dama ged by using excessive clamping force. 16. Using a 10 mm socke t wr ench, remove the 4 screws (43) from the air valve (40) and complete ly remove air valve assembly from air cyl inder (21). Also remove the two cover gaskets 18 ). If you are ...

  • Graco 3A1495C - page 7

    Instructions 3A1495C 7 Pump Reassembly NOTE: The following instructions d escribe the proce- dure to follow to reassemble a complet ely disassemb led LD grease pump. Depending on the rep air/maintenance procedure you are perfor ming on the pump, it may not be entirely disassembled . Se e the specific section(s) related to your repair/r eplacement k ...

  • Graco 3A1495C - page 8

    Instructions 8 3A1495C 6. Install the 5 screws (4) wrench tight only. NOTE: If installing a new ai r cylinder (27), the mat- ing holes are not th readed by desig n. Use thread forming scre ws (4) to f orm thread s as they ar e being installed. Torque to 95-105 in.-lbs (10.7 - 11.8 N.m) to ensure full thread formation. 7. To ensure there is a prop e ...

  • Graco 3A1495C - page 9

    Instructions 3A1495C 9 17. Screw the piston rod (23) an d the connecting rod (32) togeth er aligning the pin hole in both pieces to allow the pin to be pushed through (Fig. 19 ). 18. Replace the pin (8 ). Use a rubber hamm er to tap the pin into plac e, being ca refu l to make sure the sides of the pin a re flush with t he outside surface of the co ...

  • Graco 3A1495C - page 10

    Instructions 10 3A1495C intake seal on the priming rod as sh own in Fig. 20. 26. Install seal retainer (29) over p riming rod (34) (Fig. 22). 27. Use an adjustable wr ench to tighten seal retaine r securely, then tor que to 45 - 55 ft lbs (61 - 75 N.m). 28. Install the priming pisto n (35 and nut (19) (Fig. 3, Fig. 4) on priming rod (3 4) Use an ad ...

  • Graco 3A1495C - page 11

    Instructions 3A1495C 11 Throat and Piston Seal Replacement Kit - 24H854 ( Fig. 25 ) Replacement parts for o-ring ( 5) installed on air piston (15), o-rings (6 and 12) installed in bottom cover ( 14), o-ring (7), u-cup seal (11) and gasket (30) installed on flange (22), pin (8) used to reassemble r od sections, and gasket (18) used later in r eassem ...

  • Graco 3A1495C - page 12

    Instructions 12 3A1495C 4. Remove nut retainer (37) from flange (22) (Fig. 28). 5. Remove u-cup seal (1 1) from flange (22) (Fig. 29 ). Grease and replace th e u-cup seal with the new p art included in the ki t and install them in the order shown in Fig. 29. NOTE: • The bearing (31) is no t included in the kit. This part is reused. The bearing ca ...

  • Graco 3A1495C - page 13

    Instructions 3A1495C 13 1. Disassemble the pump following Disassembly Steps 1-14 (pages 3-5) only. 2. Use a pick to remove the gasket (30) installed between the flange (22) and tu be (36) (Fig. 32). Grease the new gasket included in the kit and install it inside the flange. 3. Use a pick to rem ove the othe r gasket (30) installed between the cylin ...

  • Graco 3A1495C - page 14

    Instructions 14 3A1495C 3. Pull spac er cylinder ( 36) away f rom pump to access pin (8) (Fig. 36). 4. Use a rubber hammer an d small punch to drive the pin (8) out. 5. Unscrew the pump low er from di splacement rod (25). Set aside pump lower for reasse mbly. 6. Use a pick to remove gasket (30) from inside the flange (22). 7. Continue pump disass e ...

  • Graco 3A1495C - page 15

    Instructions 3A1495C 15 Fig. 38. 4. Remove pilot valve (20) from the old air cylinde r (21). Apply a light coat of grease to o-rings. 5. Install pilot valve (20) in to new air cylinder included in the kit (Fig. 39). To rq ue to 95-1 05 in. lbs (10.7-11.9 N.m). 6. Apply a thin co at of grease to o-rings (5) and o-ring on bottom co ver (14). I nstall ...

  • Graco 3A1495C - page 16

    All written and visual data contained in this document reflects the latest product info r mation available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents. Original instructions. This m anual contains English . MM3A1495 Graco Headquarters: Minne apo ...

メーカー Graco カテゴリー Water Pump

Graco 3A1495Cのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3A1495Cの取扱説明書
- Gracoの製品カード
- パンフレット
- またはGraco 3A1495Cの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Graco 3A1495Cの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Graco 3A1495Cの取り付け説明書、サービスマニュアル、簡易説明書、またはGraco 3A1495Cのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Graco 3A1495Cの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Graco 3A1495Cデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGraco 3A1495Cを使用するのを助ける技術的文書のことです。説明書は通常、全てのGraco 3A1495Cユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Gracoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Graco 3A1495Cの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGraco 3A1495Cの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Graco 3A1495Cに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Graco 3A1495Cデバイスの基本機能を使うにあたってのヒント。 Graco 3A1495Cのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Graco 3A1495Cに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGraco 3A1495Cのメーカー/サービスへの連絡先に関する情報。

Graco 3A1495Cについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGraco 3A1495Cの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGraco 3A1495Cで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)