Bedienungsanleitung Ingersoll-Rand 7872-F

12 Seiten 0.91 mb
Download

Zur Seite of 12

Summary
  • Ingersoll-Rand 7872-F - page 1

    Tool Products OPERATOR’S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION M10 MANUAL 58 Released: 5/79 Revised: 3-10-95 “2200” SERIES SHORT GRINDERS Models: 7870-F-( ), 7871-F-( ), 7872-F and 7873-F. Form: 1558-2 READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE FOLL ...

  • Ingersoll-Rand 7872-F - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Do not carry the tool by the hose. Do not overreach when operating this tool. Keep body stance balanced and firm. ...

  • Ingersoll-Rand 7872-F - page 3

    ROUTINE LUBRICATION REQUIREMENTS M10 58 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). if an in line or air line lubricator is not ...

  • Ingersoll-Rand 7872-F - page 4

    MODEL IDENTIFICATION The grinder models listed in the model identification table above are furnished with collet assembly 41753-o as standard equipment and are intended for use with mounted Wheels and shall not be used with other type grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer is attached to the grinder. Se ...

  • Ingersoll-Rand 7872-F - page 5

    GRINDING WHEEL MOUNTING INSTRUCTIONS M10 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool. Check abrasive wheels prior to mounting for chips or cracks. Cracked or wheels sha ...

  • Ingersoll-Rand 7872-F - page 6

    DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and Instal- lation” section, To minimize the ...

  • Ingersoll-Rand 7872-F - page 7

    TYPICAL CROSS SECTION OF TOOL Ml0 58 7 ...

  • Ingersoll-Rand 7872-F - page 8

    MOTOR SECTION DISASSEMBLY Remove motor assembly from housing as outlined on page 6. Remove retaining nut (33694). Grasp cylinder in one hand and tap threaded end of rotor with a soft face hammer; motor will come apart. ASSEMBLY NOTE: Pack bearings with ARO 33153 grease and coat i.d. of cyl- inder with ARO 29665 spindle oil upon assembly. Assemble t ...

  • Ingersoll-Rand 7872-F - page 9

    HEAD SECTION Ml0 DISASSEMBLY ASSEMBLY 58 Remove nut (36776) and valve components can be removed from head. Lubricate “0” ring (Y325-7) with ARO 38460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32656), reg- ulator and seal (36781) to head and secure with nut (36776). NOTE: Align notch (or hole) in side of regulator with ...

  • Ingersoll-Rand 7872-F - page 10

    HEAD SECTION DISASSEMBLY Remove nut (36778) and valve components can be removed from head. To remove throttle button (36745), remove roll pin (Y178-212). ASSEMBLY Lubricate “0” ring (Y326-7) with ARO 36460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32858), reg- ulator and seal (36781) to head and secure with nut (36776 ...

  • Ingersoll-Rand 7872-F - page 11

    ACCESSORIES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLETNUT-41751 COLLET BODY - 41752 COLLET NUT DIA. - 3/4” COLLET BODY DIA. - 21/32” 3/8” - 24 THREAD 0VER ALL LENGTH - 2 1/4” 44127-( ) ERICKSON 3-PIECE COLLET ASSEMBLY M10 58 33226-( ) 3-PIECE COLLET ASSEMBLY COLLET NUT - 33220 COLLET BODY - 32218 COLLET NUT DIA. - 15/16” CUP RING - 33221 CO ...

  • Ingersoll-Rand 7872-F - page 12

    TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTION OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDlTlON LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE HARD TO OPERATE. TOOL WILL N ...

Produzent Ingersoll-Rand Kategorie Grinder

Dokumente, die wir vom Produzenten des Geräts Ingersoll-Rand 7872-F erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Ingersoll-Rand
- Bedienungsanleitungen 7872-F
- Produktkarten Ingersoll-Rand
- Informationsbroschüren
- oder Energieetiketten Ingersoll-Rand 7872-F
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Ingersoll-Rand 7872-F.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Ingersoll-Rand 7872-F, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Ingersoll-Rand 7872-F. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Ingersoll-Rand 7872-F ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Ingersoll-Rand 7872-F, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Ingersoll-Rand 7872-F hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Ingersoll-Rand 7872-F verständlich ist.

Eine gänzliche Bedienungsanleitung von Ingersoll-Rand sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Ingersoll-Rand 7872-F bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Ingersoll-Rand 7872-F befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Ingersoll-Rand 7872-F, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Ingersoll-Rand 7872-F - die uns die ersten Schritte während der Nutzung von Ingersoll-Rand 7872-F erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Ingersoll-Rand 7872-F hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Ingersoll-Rand 7872-F im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Ingersoll-Rand 7872-F?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ingersoll-Rand 7872-F nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ingersoll-Rand 7872-F hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)