Ingersoll-Rand 7872-Fの取扱説明書

12ページ 0.91 mb
ダウンロード

ページに移動 of 12

Summary
  • Ingersoll-Rand 7872-F - page 1

    Tool Products OPERATOR’S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION M10 MANUAL 58 Released: 5/79 Revised: 3-10-95 “2200” SERIES SHORT GRINDERS Models: 7870-F-( ), 7871-F-( ), 7872-F and 7873-F. Form: 1558-2 READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE FOLL ...

  • Ingersoll-Rand 7872-F - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Do not carry the tool by the hose. Do not overreach when operating this tool. Keep body stance balanced and firm. ...

  • Ingersoll-Rand 7872-F - page 3

    ROUTINE LUBRICATION REQUIREMENTS M10 58 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). if an in line or air line lubricator is not ...

  • Ingersoll-Rand 7872-F - page 4

    MODEL IDENTIFICATION The grinder models listed in the model identification table above are furnished with collet assembly 41753-o as standard equipment and are intended for use with mounted Wheels and shall not be used with other type grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer is attached to the grinder. Se ...

  • Ingersoll-Rand 7872-F - page 5

    GRINDING WHEEL MOUNTING INSTRUCTIONS M10 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool. Check abrasive wheels prior to mounting for chips or cracks. Cracked or wheels sha ...

  • Ingersoll-Rand 7872-F - page 6

    DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and Instal- lation” section, To minimize the ...

  • Ingersoll-Rand 7872-F - page 7

    TYPICAL CROSS SECTION OF TOOL Ml0 58 7 ...

  • Ingersoll-Rand 7872-F - page 8

    MOTOR SECTION DISASSEMBLY Remove motor assembly from housing as outlined on page 6. Remove retaining nut (33694). Grasp cylinder in one hand and tap threaded end of rotor with a soft face hammer; motor will come apart. ASSEMBLY NOTE: Pack bearings with ARO 33153 grease and coat i.d. of cyl- inder with ARO 29665 spindle oil upon assembly. Assemble t ...

  • Ingersoll-Rand 7872-F - page 9

    HEAD SECTION Ml0 DISASSEMBLY ASSEMBLY 58 Remove nut (36776) and valve components can be removed from head. Lubricate “0” ring (Y325-7) with ARO 38460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32656), reg- ulator and seal (36781) to head and secure with nut (36776). NOTE: Align notch (or hole) in side of regulator with ...

  • Ingersoll-Rand 7872-F - page 10

    HEAD SECTION DISASSEMBLY Remove nut (36778) and valve components can be removed from head. To remove throttle button (36745), remove roll pin (Y178-212). ASSEMBLY Lubricate “0” ring (Y326-7) with ARO 36460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32858), reg- ulator and seal (36781) to head and secure with nut (36776 ...

  • Ingersoll-Rand 7872-F - page 11

    ACCESSORIES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLETNUT-41751 COLLET BODY - 41752 COLLET NUT DIA. - 3/4” COLLET BODY DIA. - 21/32” 3/8” - 24 THREAD 0VER ALL LENGTH - 2 1/4” 44127-( ) ERICKSON 3-PIECE COLLET ASSEMBLY M10 58 33226-( ) 3-PIECE COLLET ASSEMBLY COLLET NUT - 33220 COLLET BODY - 32218 COLLET NUT DIA. - 15/16” CUP RING - 33221 CO ...

  • Ingersoll-Rand 7872-F - page 12

    TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTION OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDlTlON LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE HARD TO OPERATE. TOOL WILL N ...

メーカー Ingersoll-Rand カテゴリー Grinder

Ingersoll-Rand 7872-Fのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 7872-Fの取扱説明書
- Ingersoll-Randの製品カード
- パンフレット
- またはIngersoll-Rand 7872-Fの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ingersoll-Rand 7872-Fの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ingersoll-Rand 7872-Fの取り付け説明書、サービスマニュアル、簡易説明書、またはIngersoll-Rand 7872-Fのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ingersoll-Rand 7872-Fの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ingersoll-Rand 7872-Fデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがIngersoll-Rand 7872-Fを使用するのを助ける技術的文書のことです。説明書は通常、全てのIngersoll-Rand 7872-Fユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ingersoll-Randの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ingersoll-Rand 7872-Fの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははIngersoll-Rand 7872-Fの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ingersoll-Rand 7872-Fに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ingersoll-Rand 7872-Fデバイスの基本機能を使うにあたってのヒント。 Ingersoll-Rand 7872-Fのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ingersoll-Rand 7872-Fに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるIngersoll-Rand 7872-Fのメーカー/サービスへの連絡先に関する情報。

Ingersoll-Rand 7872-Fについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもIngersoll-Rand 7872-Fの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがIngersoll-Rand 7872-Fで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)