English dropdown-ico

Manual Ingersoll-Rand 7872-F

12 pages 0.91 mb
Download

Go to site of 12

Summary
  • Ingersoll-Rand 7872-F - page 1

    Tool Products OPERATOR’S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION M10 MANUAL 58 Released: 5/79 Revised: 3-10-95 “2200” SERIES SHORT GRINDERS Models: 7870-F-( ), 7871-F-( ), 7872-F and 7873-F. Form: 1558-2 READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE FOLL ...

  • Ingersoll-Rand 7872-F - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Do not carry the tool by the hose. Do not overreach when operating this tool. Keep body stance balanced and firm. ...

  • Ingersoll-Rand 7872-F - page 3

    ROUTINE LUBRICATION REQUIREMENTS M10 58 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). if an in line or air line lubricator is not ...

  • Ingersoll-Rand 7872-F - page 4

    MODEL IDENTIFICATION The grinder models listed in the model identification table above are furnished with collet assembly 41753-o as standard equipment and are intended for use with mounted Wheels and shall not be used with other type grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer is attached to the grinder. Se ...

  • Ingersoll-Rand 7872-F - page 5

    GRINDING WHEEL MOUNTING INSTRUCTIONS M10 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool. Check abrasive wheels prior to mounting for chips or cracks. Cracked or wheels sha ...

  • Ingersoll-Rand 7872-F - page 6

    DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and Instal- lation” section, To minimize the ...

  • Ingersoll-Rand 7872-F - page 7

    TYPICAL CROSS SECTION OF TOOL Ml0 58 7 ...

  • Ingersoll-Rand 7872-F - page 8

    MOTOR SECTION DISASSEMBLY Remove motor assembly from housing as outlined on page 6. Remove retaining nut (33694). Grasp cylinder in one hand and tap threaded end of rotor with a soft face hammer; motor will come apart. ASSEMBLY NOTE: Pack bearings with ARO 33153 grease and coat i.d. of cyl- inder with ARO 29665 spindle oil upon assembly. Assemble t ...

  • Ingersoll-Rand 7872-F - page 9

    HEAD SECTION Ml0 DISASSEMBLY ASSEMBLY 58 Remove nut (36776) and valve components can be removed from head. Lubricate “0” ring (Y325-7) with ARO 38460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32656), reg- ulator and seal (36781) to head and secure with nut (36776). NOTE: Align notch (or hole) in side of regulator with ...

  • Ingersoll-Rand 7872-F - page 10

    HEAD SECTION DISASSEMBLY Remove nut (36778) and valve components can be removed from head. To remove throttle button (36745), remove roll pin (Y178-212). ASSEMBLY Lubricate “0” ring (Y326-7) with ARO 36460 lubricant and as- semble to valve stem. Assemble valve stem, spring (32858), reg- ulator and seal (36781) to head and secure with nut (36776 ...

  • Ingersoll-Rand 7872-F - page 11

    ACCESSORIES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLETNUT-41751 COLLET BODY - 41752 COLLET NUT DIA. - 3/4” COLLET BODY DIA. - 21/32” 3/8” - 24 THREAD 0VER ALL LENGTH - 2 1/4” 44127-( ) ERICKSON 3-PIECE COLLET ASSEMBLY M10 58 33226-( ) 3-PIECE COLLET ASSEMBLY COLLET NUT - 33220 COLLET BODY - 32218 COLLET NUT DIA. - 15/16” CUP RING - 33221 CO ...

  • Ingersoll-Rand 7872-F - page 12

    TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTION OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDlTlON LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE HARD TO OPERATE. TOOL WILL N ...

Manufacturer Ingersoll-Rand Category Grinder

Documents that we receive from a manufacturer of a Ingersoll-Rand 7872-F can be divided into several groups. They are, among others:
- Ingersoll-Rand technical drawings
- 7872-F manuals
- Ingersoll-Rand product data sheets
- information booklets
- or energy labels Ingersoll-Rand 7872-F
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ingersoll-Rand 7872-F.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ingersoll-Rand 7872-F, service manual, brief instructions and user manuals Ingersoll-Rand 7872-F. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ingersoll-Rand 7872-F.

Similar manuals

A complete manual for the device Ingersoll-Rand 7872-F, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ingersoll-Rand 7872-F by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ingersoll-Rand 7872-F.

A complete Ingersoll-Rand manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ingersoll-Rand 7872-F - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ingersoll-Rand 7872-F, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ingersoll-Rand 7872-F, that we can find in the current document
3. Tips how to use the basic functions of the device Ingersoll-Rand 7872-F - which should help us in our first steps of using Ingersoll-Rand 7872-F
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ingersoll-Rand 7872-F
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ingersoll-Rand 7872-F in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ingersoll-Rand 7872-F?

Use the form below

If you did not solve your problem by using a manual Ingersoll-Rand 7872-F, ask a question using the form below. If a user had a similar problem with Ingersoll-Rand 7872-F it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)