-
Emerson 00825-0100-4593 - page 1
www.rosemount.com ¢00825-0100-4360N¤ Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 Step 1: Mount the T ransmitter Step 2: Consider Housing Rotation Step 3: Connect the Wiring and Power Up Step 4: Set Switches Step 5: Configuration Step 6: T rim the T ransmitt er Product Certifications Sta r t End Rosemount 1 151 Pres ...
-
Emerson 00825-0100-4593 - page 2
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 2 W ARNING Explosions could result in death or serious injury: Installation of this tr ansmitter in a n explosive env iron ment must be in accordan ce wit h t he approp riat e local, national, and inter national st andards, code s, and pract ices. Please review the approval ...
-
Emerson 00825-0100-4593 - page 3
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 3 S TE P 1: M OUNT THE T RANSMI TTER A. Applications Liquid Flow Application s 1. Place taps to the side of the line. 2. Mount beside or below the taps. Gas Flow Applicatio ns 1. Place taps in the top or side of the line. 2. Mount beside or above the taps. Steam Flow Applic ...
-
Emerson 00825-0100-4593 - page 4
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 4 S TE P 1 CONTI NUED ... B. Optional Mounting Brackets When installing the transmitter to one of the optional mounting brackets, torque the bracket bolts to 125 in.-lbs. (0,9 N-m). Pipe Mount Panel Mount (1) (1) Panel bolts are customer supplied. Flat Mount 4593_Rev_BA.fm P ...
-
Emerson 00825-0100-4593 - page 5
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 5 S TE P 1 CONTI NUED ... C. O-rings with Flange Adapters W ARNING Whenever the flanges or adapters are removed, vi su ally inspect the o-rings. Replace them if there are any signs of damage, such as nicks or cuts. If you replace the o-rings, re-torque the flange bolts and ...
-
Emerson 00825-0100-4593 - page 6
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 6 S TE P 2: C ON SIDER H OUSING R OT ATION T o improve field access or to better view the optional LCD d isplay: 1. Loosen the housing lock nut. 2. Rotate the housing clockwise to the desired posit ion – up to 90° from its o riginal position. Over rotating will damage the ...
-
Emerson 00825-0100-4593 - page 7
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 7 S TE P 3: C ON NECT THE W IRING AND P OWER U P Use the following steps to wire the transmitter: 1. Remove the housing cover on the side marked TERMINALS on the namepla te. 2. Connect the positive lead to the “+” termin a l and the negative lead to the “–” termin ...
-
Emerson 00825-0100-4593 - page 8
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 8 S TE P 3 CONTI NUED ... Power Supply The dc power supply should provide power with less than tw o percent ripple. The total resistance load is the sum of the resistance of the signal leads and the load resistance of the controller , indicator , and related pieces. Note tha ...
-
Emerson 00825-0100-4593 - page 9
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 9 S TE P 4: C ON FIGURE THE T RANSMITTER Failure Mode Alarm Switch 1. Remove the housing cover . 2. Locate the failure mode switch (see Figure 3). 3. Move the switch to the desired alarm setting. T o set the failure mo de to high alarm, position the switch toward “HI.” ...
-
Emerson 00825-0100-4593 - page 10
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 10 S TE P 5: C AL IBRATE THE T RANSMITTER V erify T ransmitter Configuration NOTE: A check ( ✓ ) indicates the basic configuration para meters. At minimum, these parameters should be verified as part of the configuration and startup procedure. T able 1. HART Communicator F ...
-
Emerson 00825-0100-4593 - page 11
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 11 S TE P 5 CONTI NUED ... Configure LCD Displa y Figure 4. Sample 1 151 LCD Display NOTE The LCD display time-out is approximately 16 se conds. If keys ar e not pressed within this period, the indicator reverts to reading the signal. Position the Decimal Point and Select t ...
-
Emerson 00825-0100-4593 - page 12
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 12 S TE P 5 CONTI NUED ... Set the Display Equivalent to a 4 mA Sign al 1. Unscrew the retaining ring shown in Figure 4 and remove the LCD display cover . 2. Press the left button for two seconds. 3. T o decrement the display numb ers, press the le ft configuration button an ...
-
Emerson 00825-0100-4593 - page 13
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 13 S TE P 6: T RIM THE T RANSMITTE R NOTE T ransmitte rs are shipped fully calibrated per reques t or by the factory d efault of full scale (span = upper range limit). Full T rim A full trim is a two-point sensor calibrat ion where two end- point pressures are applied, and ...
-
Emerson 00825-0100-4593 - page 14
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 14 S TE P 6 CONTI NUED ... Using the T ransmitter Zero Adjustment Buttons Perform the following steps to perform a rerange using the zer o adjustment buttons (see Figure 3). 1. Apply a pressure equivalent to the lower calibra ted value on the high side of the transmitter . 2 ...
-
Emerson 00825-0100-4593 - page 15
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 15 P RODUCT C E RTIFICATI ONS Approved Manufacturi ng Locations Rosemount Inc. — Chanhassen, Minnesota, USA Fisher-Rosemount Gmb H & Co. — Wessling, Germany Emerson Process Management Asia Pacific Private Limited — Singapore Beijing Rosemount Far East Instrument C ...
-
Emerson 00825-0100-4593 - page 16
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 16 Canadian Certifications Canadian St andards Association (CSA) Approvals E6 Explosion Proof for Class I, Division 1, Gr oups C and D; Class II, Division 1, Group s E, F , and G; Class III, Division 1 Hazardous Loc ations. Suit able fo r C la ss I , Di v is i on 2, Groups A ...
-
Emerson 00825-0100-4593 - page 17
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 17 N1 A TEX T y pe N and Dust Certification Certificate Number: BAS99A TEX3293X A TEX Marking: II 3 GD Ex nL IIC T5 (-40 °C T amb 40 °C) EX nL IIC T4 (-40 °C T amb 80 °C) Dust Rating: T90 °C (T amb = -20 °C to 40 °C) Ui = 45 Vdc ma ximum IP66 Special ...
-
Emerson 00825-0100-4593 - page 18
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 18 N7 T ype N Certificate Number: Aus Ex 122X Ex n IIC T5 (T a = 80 °C) / T6 IP66 Special Conditions for safe use (x): 1. It is a condition of safe use that a nomi nal voltage of 30 V for Ex n application shall not be exceeded. 2. It is a condition of safe use that when the ...
-
Emerson 00825-0100-4593 - page 19
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 19 DoC 4593_Rev_BA.fm Page 19 Friday, August 7, 2009 3:38 PM ...
-
Emerson 00825-0100-4593 - page 20
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 20 4593_Rev_BA.fm Page 20 Friday, August 7, 2009 3:38 PM ...
-
Emerson 00825-0100-4593 - page 21
Quick Installation Guid e 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 21 4593_Rev_BA.fm Page 21 Friday, August 7, 2009 3:38 PM ...
-
Emerson 00825-0100-4593 - page 22
Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1 151 22 4593_Rev_BA.fm Page 22 Friday, August 7, 2009 3:38 PM ...
¿Tienes una pregunta acerca de Emerson 00825-0100-4593?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Emerson 00825-0100-4593, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Emerson 00825-0100-4593 probablemente compartirá una forma de solucionarlo.