Manuel d’utilisation Faber Remote Blower

16 pages 1.24 mb
Télécharger

Aller à la page of 16

Summary
  • Faber Remote Blower - page 1

    Instruction Manual READ AND SA VE THESE INSTRUCTIONS The Installer must leave these instructions with the homeowner . The homeowner must keep these instructions for future reference and for local electrical inspectors’ use. Concept Remote Blower ...

  • Faber Remote Blower - page 2

    2 EN CONTENTS WARNING 3 CHARACTERISTICS 5 INST ALLA TION 8 USE 13 MAINTENANCE 1 4 ...

  • Faber Remote Blower - page 3

    3 EN READ THESE INSTRUCTIONS BEFORE YOU ST ART INST ALLING THIS RANGEHOOD READ AND SA VE THESE INSTRUCTIONS W ARNING: - T O REDUCE THE RISK OF A RANGE T OP GREASE FIRE : Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Always turn hood ON ...

  • Faber Remote Blower - page 4

    4 EN This appliance should be connected directly to the fused disconnect (or circuit breaker) through flexible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the appliance can be moved if servicing is ever necessary . A UL Listed, 1/2" con duit connector must be provided at each end of the power supply cable (a ...

  • Faber Remote Blower - page 5

    5 EN 1 3 4 5 10 11 12 13 G E F D C A 2 CHARACTERISTICS Components Q.ty 1 1 Hood Body , complete with: Blower, Filters, Controls 2 1 Built-in hood body case 3 1 Rear remote motor connection panel 4 1 T op air outlet flange with valve 5 1 T op air outlet plug 10 1 Light 11 4 Support arms 12 2 Bush masking plug 13 2 Arm support bush A 10 Screws 3,5 x ...

  • Faber Remote Blower - page 6

    6 EN Dimensional chart - Hood Distance from the Hob ...

  • Faber Remote Blower - page 7

    7 EN Dimensional chart - LIGHT ...

  • Faber Remote Blower - page 8

    8 EN INST ALLA TION The hood can be installed in the following ways: top air outlet, bottom air outlet, rear air outlet. Once the desired configuration has been chosen (see the diagrams below) it will be necessary to provide an opening in the wall where to house the built-in hood body case. Besides the air ducting pipes, basing on the chosen config ...

  • Faber Remote Blower - page 9

    9 EN LIGHTING UNIT INST ALLA TION SCHEME LIGHTING UNIT LOWER BORDER SHALL BE INST ALLED A T THE MINIMUM DIST ANCE OF 34 9/16 IN. ABOVE THE COOKING SURF ACE. W ith the aid of the drilling template provided mark the necessary holes and drill them. ø15/16 TO P OR BOTTOM AIR OUTLET CONFIGURA TION The hood is manufactured with the air outlet at the top ...

  • Faber Remote Blower - page 10

    10 EN REAR AIR OUTLET CONFIGURA TION • Remove the suction panel by unfastening the 8 screws around the frame. • Remove the metal grease filters. • Remove the metal profile fixed to the flange by unfastening the 5 screws. • Fit the air outlet plug into the top air outlet. • Remove the rear air outlet plug . Built-in hood body case installa ...

  • Faber Remote Blower - page 11

    11 EN Hood body installation • In case of the bottom air outlet configuration the hood body has to be turned 180°. • Remove the top cover of the terminal box by unfastening the two screws fixing it to the hood casing. • W ith the aid of pliers brake through a hole inside the terminal box providing thus for a passage of the electrical connect ...

  • Faber Remote Blower - page 12

    12 EN Lighting unit installation • Provide for passage of the electrical connection wires with the hood body . • Slide the top cover downwards, unfastening the two side screws and taking care not to scratch the tubular support members. • Insert the 4 plugs D into the earlier drilled holes. • Decide the height of the light; loosen the grub s ...

  • Faber Remote Blower - page 13

    13 EN Electrical connection ELECTRICAL SHOCK HAZARD • Disconnect power before making electrical connctions. • Connect ground wire to green ground screw in terminal box. ! W ARNING green ground screw hood wiring purple wiring red wiring hood wiring black wiring white wiring power supply conduit light wiring exterior blower wiring twist-on connec ...

  • Faber Remote Blower - page 14

    14 EN MAINTENANCE Grease filters CLEANING MET AL GREASE FIL TERS • Alarm signal reset • Switch off the lights and extractor motor . • Press button T3 for at least 3 seconds, until the leds start to flash. Cleaning the filters • Open the suction cover using the lever provided. • The filters are washable and must be cleaned when the Led S1 ...

  • Faber Remote Blower - page 15

    15 EN Electric Diagram Lighting LIGHT REPLACEMENT 20 W halogen light. • Extract the lamp from the Support. • Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes. ...

  • Faber Remote Blower - page 16

    436002499_02 - 041 103 ...

Fabricant Faber Catégorie Blower

Les documents que nous recevons du fabricant de l'appareilFaber Remote Blower peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Faber
- manuels d’utilisations Remote Blower
- fiches produit Faber
- dépliants
- ou étiquettes-énergie Faber Remote Blower
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Faber Remote Blower.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Faber Remote Blower, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Faber Remote Blower. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Faber Remote Blower.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Faber Remote Blower, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Faber Remote Blower par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Faber Remote Blower.

Le manuel d’utilisation complet Faber, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Faber Remote Blower - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Faber Remote Blower, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lFaber Remote Blower qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Faber Remote Blower - qui devraient nous aider dans les premières étapes lors de l'utilisation Faber Remote Blower
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Faber Remote Blower
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Faber Remote Blower dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Faber Remote Blower?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Faber Remote Blower, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Faber Remote Blower il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)