-
HSM HSM FA 500.2 - page 1
HSM F A 500.2 OPERA TING INSTRUCTIONS P APER SHREDDER Combination with HSM KP 80 Keep this instruction for future use! 1.655.999.1 12 – 0702 english ...
-
HSM HSM FA 500.2 - page 2
2 0702 F A 500.2 HSM GmbH + Co. KG Bahnhofstrasse 1 15 D-88682 Salem / Germany T el.: +49 (0) 75 53 / 822-0 Fax.: +49 (0) 75 53 / 822-160 E-Mail: info@hsm-online.de www .hsm-online.de Contents 1. Proper use, warranty ................................................................................................................. 3 2. Safety instruc ...
-
HSM HSM FA 500.2 - page 3
0702 3 F A 500.2 Danger of injury Do not reach into the paper feed opening. Splinters can cause injury Wear protective goggles when de- stroying diskettes, CDs and hard credit cards. Danger of injury during intake Do not go near the paper feed open- ing with long hair , loose clothing, ties, scarves, necklaces, bracelets etc. Do not destroy any mat ...
-
HSM HSM FA 500.2 - page 4
4 0702 F A 500.2 Combination with HSM KP 80 3. Overview 1 7 4 3 2 5 1 Main switch (only solo-version) 2 Keypad 3 Emergency stop button 4 Loading tray 5 Intake conveyor , paper feed opening 6 Braking swivel castors 7 Nameplate 8 Oiler 8 6 ...
-
HSM HSM FA 500.2 - page 5
0702 5 F A 500.2 4. Dimensions Space requirements for operation and maintenance Load on rollers HSM F A 500.2 Combination-version HSM F A 500.2 Stand alone-version Combination-version Stand alone-version 2 x 180 kg 2 x 180 kg 1590 1925 max. 1410 1185 960 630 500 1155 880 500 880 1155 560 910 960 630 1000 500 1255 3500 1000 500 1255 2590 1410 1185 8 ...
-
HSM HSM FA 500.2 - page 6
6 0702 F A 500.2 5. T ransportation, installation • During transport, observe the high centre of gravity of the paper shredder! • Place the pallet with the shredder in its packaging on a smooth, level surface. • Observe the instructions for unpacking. • If you need to move the shredder through narrow doors, you can wait until it is at its ? ...
-
HSM HSM FA 500.2 - page 7
0702 7 F A 500.2 • Insert the connecting screw (5) and the clamp (6) on the end of the hose and secure the unit on the oiler . • Pour the oil into the oiler container from the two bot- tles supplied. Ready for operation Green LED Light has no function. Start button The shredder switches on. The feed belt moves in the intake direction. Stop butt ...
-
HSM HSM FA 500.2 - page 8
8 0702 F A 500.2 7. Start-up and inspecting the safety devices Check that the safety devices are working properly: • At the start of each shift • After any maintenance or repair work Do not start the machine until you have checked the safety devices and found them to be in perfect working order . If any defect arises during operation stop the m ...
-
HSM HSM FA 500.2 - page 9
0702 9 F A 500.2 Safety switch on the inspection door (only stand alone-version) Open the inspection door . The shredder must switch off immediately and the ” Safety circuit interrupted ” LED must light up. The machine will only start again once you have closed the inspection door . Safety switch on the protective fl ap (only stand alone-versi ...
-
HSM HSM FA 500.2 - page 10
10 0702 F A 500.2 8. Malfunctions Check the following before calling customer service: • Is the power plug connected? • Is the shredder switched on? • Is there a paper jam in the shredder? • Has the motor been overloaded? Paper jam Y ou have fed in too much paper . ` The red LED on the keypad blinks. ` The cutting block automatically runs i ...
-
HSM HSM FA 500.2 - page 11
0702 11 F A 500.2 Checking the chain tension (twice yearly) • Switch off the shredder . • Pull out the power plug. • Remove the left side cover . The sagging of the chain should be 9 to 14 mm. If you need to tighten the chain: • Loosen the clamping nuts (1). • Lower the motor until the sagging is 9 to 14 mm. • T ighten the clamping nuts ...
-
HSM HSM FA 500.2 - page 12
12 0702 F A 500.2 Tightening the feed belt The feed belt should not slip when loaded with material. • Switch off the shredder . • Remove the feeding table and the left and right side covers. • Loosen the hexagon nuts (1) of the tension roll on the left and right side. • Loosen the lock nuts (2) of the tensioning bolts (3). • T ighten the ...
-
HSM HSM FA 500.2 - page 13
0702 13 F A 500.2 Declaration of Conformity Machinery directive 98 / 37 / EG EMC directive 89 / 336 / EWG Low voltage directive 73 / 23 / EWG The manufacturer HSM GmbH + Co. KG, Bahnhofstrasse 1 15, D-88682 Salem declares herewith, that the paper shredder (Solo machine) HSM F A 500.2 corresponds with the above mentioned EC Machine Directive includi ...
-
HSM HSM FA 500.2 - page 14
14 0702 F A 500.2 Solo 400 V 12. Electric wiring diagrams Solo 400 V / 50 Hz Legend: =A V : Shredder +S: in switch cabinet +MA: on machine +BF: Keypad ...
-
HSM HSM FA 500.2 - page 15
0702 15 F A 500.2 Solo 400 V ...
-
HSM HSM FA 500.2 - page 16
16 0702 F A 500.2 Solo 400 V ...
-
HSM HSM FA 500.2 - page 17
0702 17 F A 500.2 Kombi 400 V Combination 400 V / 50 Hz ...
-
HSM HSM FA 500.2 - page 18
18 0702 F A 500.2 Kombi 400 V ...
-
HSM HSM FA 500.2 - page 19
0702 19 F A 500.2 Kombi 400 V ...
-
HSM HSM FA 500.2 - page 20
20 0702 F A 500.2 Kombi 400 V ...
HSM HSM FA 500.2についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHSM HSM FA 500.2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHSM HSM FA 500.2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。