English dropdown-ico

Manual Stanley Black & Decker PR41

20 pages 1.53 mb
Download

Go to site of 20

Summary
  • Stanley Black & Decker PR41 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 32472 8/2014 V er . 5 USER MANUAL Safety , Operation and Maintenance PR41 HYDRAULIC PRUNER ...

  • Stanley Black & Decker PR41 - page 2

    ...

  • Stanley Black & Decker PR41 - page 3

    PR41 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer . Please read the following warning. For the nearest authorized and certie ...

  • Stanley Black & Decker PR41 - page 4

    4 ► PR41 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker PR41 - page 5

    PR41 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs. ...

  • Stanley Black & Decker PR41 - page 6

    6 ► PR41 User Manual The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (ref. ANSI Z133.1-2000) WORKING IN PROXIMITY T O ELECTRICAL HAZARDS An inspection shall be made by a qualied arborist to determine whether an electrical hazard exists before cli ...

  • Stanley Black & Decker PR41 - page 7

    PR41 User Manual ◄ 7 T able 2 – Minimum approach distances to energized conductors for persons other than qualied line- clearance arborists and qualied line- clearance arborist trainees. Nominal V oltage kV phase-to-phase 1 Distance ft-in m 0.0 – 1.0 10–00 3.05 1.1 – 15.0 10–00 3.05 15.1 – 36.0 10–00 3.05 36.1 – 50.0 10–00 ...

  • Stanley Black & Decker PR41 - page 8

    8 ► PR41 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA TOR. SEE OTHER SIDE 1. FAILURE TO USE H ...

  • Stanley Black & Decker PR41 - page 9

    PR41 User Manual ◄ 9 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker PR41 - page 10

    10 ► PR41 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS 4-6 ...

  • Stanley Black & Decker PR41 - page 11

    PR41 User Manual ◄ 1 1 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacit ...

  • Stanley Black & Decker PR41 - page 12

    12 ► PR41 User Manual PREP ARA TION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required. After instal- lation of hoses and couplers a unit may be put to use. CHECK HYDRAULIC P ...

  • Stanley Black & Decker PR41 - page 13

    PR41 User Manual ◄ 13 LA TERAL BRANCH BRANCH T O BE CUT BLADE T OWARDS LA TERAL BRANCH WILL LEA VE EDGE FLUSH WITH LA TERAL BRANCH NO STUB LEFT Figure 2. Example of Lateral Branch Cut WARNING The following are general wood cutting procedures and techniques. Differences in the terrain, vegetation, and type of wood will make this information more o ...

  • Stanley Black & Decker PR41 - page 14

    14 ► PR41 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hydrau- lic system. • Always store the tool in a clean dry ...

  • Stanley Black & Decker PR41 - page 15

    PR41 User Manual ◄ 15 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the tool, always make sure the hydraulic power source is supplying the cor - rect hydraulic ow and pressure as listed in the table. Use a owmeter know to be accurate. Check ...

  • Stanley Black & Decker PR41 - page 16

    16 ► PR41 User Manual Capacity......................................................................................................................................2-1/4 inch/5.7 cm cut Pressure Range ................................................................................................................ 1000–2000 psi/70–140 bar Maxim ...

  • Stanley Black & Decker PR41 - page 17

    PR41 User Manual ◄ 17 PR41 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker PR41 - page 18

    18 ► PR41 User Manual ITEM P ART NO. QTY DESCRIPTION 44 28502 1 NAME T AG 45 25910 1 NOTICE STICKER 46 51 183 1 TRIGGER 47 05268 1 HEX SLOTTED NUT 03693 1 CLOSED CENTER DECAL (PR41231 ONL Y) 03972 1 FEMALE COUPLER (SUPPLIED W/ PR41 13103 ONL Y) 03973 1 MALE COUPLER (SUPPLIED W/ PR41 13103 ONL Y) 03971 1 COUPLER SET (PR41 1303 ONL Y) 32473 1 SEAL ...

  • Stanley Black & Decker PR41 - page 19

    ...

  • Stanley Black & Decker PR41 - page 20

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Manufacturer Stanley Black & Decker Category Pole Saw

Documents that we receive from a manufacturer of a Stanley Black & Decker PR41 can be divided into several groups. They are, among others:
- Stanley Black & Decker technical drawings
- PR41 manuals
- Stanley Black & Decker product data sheets
- information booklets
- or energy labels Stanley Black & Decker PR41
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stanley Black & Decker PR41.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stanley Black & Decker PR41, service manual, brief instructions and user manuals Stanley Black & Decker PR41. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stanley Black & Decker PR41.

Similar manuals

A complete manual for the device Stanley Black & Decker PR41, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stanley Black & Decker PR41 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stanley Black & Decker PR41.

A complete Stanley Black & Decker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stanley Black & Decker PR41 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stanley Black & Decker PR41, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stanley Black & Decker PR41, that we can find in the current document
3. Tips how to use the basic functions of the device Stanley Black & Decker PR41 - which should help us in our first steps of using Stanley Black & Decker PR41
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stanley Black & Decker PR41
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stanley Black & Decker PR41 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stanley Black & Decker PR41?

Use the form below

If you did not solve your problem by using a manual Stanley Black & Decker PR41, ask a question using the form below. If a user had a similar problem with Stanley Black & Decker PR41 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)