English dropdown-ico

Manual Pelco C2461M-A

16 pages 0.43 mb
Download

Go to site of 16

Summary
  • Pelco C2461M-A - page 1

    150 Series Camclosure ® Integrated Camera System with LowLight ™ DSS T echnology C2461M-A (7/03) ® INST ALLA TION/OPERA TION In-Ceiling Mount ...

  • Pelco C2461M-A - page 2

    2 C2461M-A (7/03) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ..................................................................................... 3 WELCOME .......................................................................................................................................... 4 INST ALL THE BACK BOX ................ ...

  • Pelco C2461M-A - page 3

    C2461M-A (7/03) 3 Heater elements could be hot! When camera power is on, use caution when adjusting the camera. CAUTION IMPORT ANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or ...

  • Pelco C2461M-A - page 4

    4 C2461M-A (7/03) WELCOME Thank you for purchasing Pelco’ s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology . Y our new ICS150 Series in-ceiling dome system includes a high- resolution, low light, color camera with auto iris and varifocal lens. The LowLight color camera has extended DSS settings to ...

  • Pelco C2461M-A - page 5

    C2461M-A (7/03) 5 INST ALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove the lower dome and place it to the side. INST ALL THE BACK BOX The installation methods for the ICS150 back box include the following: • Attach Directly to a Wall/Ceiling • Attach to a 4S De ...

  • Pelco C2461M-A - page 6

    6 C2461M-A (7/03) Attach to a 4S Deep Electrical Box Refer to Figure 2 for the following steps. The installation instructions assume that the 4S box was previously installed. 1. Attach adapter plate to the 4S box with the two 8-32 x .750-inch screws supplied. 2. Connect the video cable. 3. Connect the power wires. V oltage Red Wire Black Wire 12 VD ...

  • Pelco C2461M-A - page 7

    C2461M-A (7/03) 7 Install in a Ceiling T ile Refer to Figure 3 for the following steps. 1. Cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile for the back box. Use the adapter plate as a template. 2. Punch four screw holes in the ceiling tile. Use the four threaded screw holes in the adapter plate as a template. 3. Attach the back box to ...

  • Pelco C2461M-A - page 8

    8 C2461M-A (7/03) Figure 4. Heater Jumper and Camera Connector Locations INST ALL THE CAMERA MODULE CHECK HEA TER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not require this heater . If the unit will never be subjected to a frost temperature, you can disable the heater , saving power requirements. T ...

  • Pelco C2461M-A - page 9

    C2461M-A (7/03) 9 Wall Mounting - The camera bracket tab points out of the enclosure and the top of the camera points up towards the tab. Ceiling Mounting - The camera bracket tab points out of the enclosure and the top of the camera is pointed in the opposite direction. CAMERA BRACKET T AB AL WA YS POINTS OUT OF THE ENCLOSURE TOP OF CAMERA CAMERA ...

  • Pelco C2461M-A - page 10

    10 C2461M-A (7/03) Figure 5. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring clockwise/counterclockwise. Refer to Figure 5. 2. T ighten the zoom locking screw . 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise. 4. T ighten the focus l ...

  • Pelco C2461M-A - page 11

    C2461M-A (7/03) 11 ON OFF DIGIT AL SLOW SHUTTER (DSS) Digital slow shutter slows the picture frame rate and increases the camera sensitivity under low light conditions. Depending on the number of fields of integration the picture will develop a granular appearance and motion may show some lag, resulting in a stereoscopic effect or streaking on fast ...

  • Pelco C2461M-A - page 12

    12 C2461M-A (7/03) VERTICAL PHASE ADJUSTMENT (24 V AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate ver tical roll reverse the 24 VAC connections on one camera. If both cameras are connected to the same transformer , this should solve the ...

  • Pelco C2461M-A - page 13

    C2461M-A (7/03) 13 Figure 6. Dome and Trim Ring Installation REINST ALL THE DOME AND TRIM RING Place the trim ring and dome over the back box. If the dome has a liner , position the viewing window over the lens of the camera. T ighten the tamper -resistant screws with the supplied 1/8-inch hollow screwdriver bit. Note that the screws are installed ...

  • Pelco C2461M-A - page 14

    14 C2461M-A (7/03) SPECIFICA TIONS BACKBOX Electrical Input V oltage: 12 VDC or 24 V AC, ± 10%, auto-sensing Power Consumption: 13 watts or less Video Connector: BNC General Operating T emperature: -50 ° to 122 ° F (-46 ° to 50 ° C) De-ices to 25 ° F (-4 ° C) Pan/T ilt Adjustment: Manual; 360 ° pan; 180 ° tilt Construction: Aluminum with s ...

  • Pelco C2461M-A - page 15

    C2461M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2461M 4/03 Preliminary manual for beta testing. C2461M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved. WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repa ...

  • Pelco C2461M-A - page 16

    World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada ® ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco C2461M-A can be divided into several groups. They are, among others:
- Pelco technical drawings
- C2461M-A manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco C2461M-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco C2461M-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco C2461M-A, service manual, brief instructions and user manuals Pelco C2461M-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco C2461M-A.

Similar manuals

A complete manual for the device Pelco C2461M-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco C2461M-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco C2461M-A.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco C2461M-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco C2461M-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco C2461M-A, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco C2461M-A - which should help us in our first steps of using Pelco C2461M-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco C2461M-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco C2461M-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco C2461M-A?

Use the form below

If you did not solve your problem by using a manual Pelco C2461M-A, ask a question using the form below. If a user had a similar problem with Pelco C2461M-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)